/dev/ada0 smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 840 EVO 120GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EXT0BB0Q User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 29 07:45:53 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Unexpected SCT status 0x0001 (action_code=4, function_code=2) Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4200) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 70) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 080 080 000 - 100355 12 Power_Cycle_Count -O--CK 099 099 000 - 46 177 Wear_Leveling_Count PO--C- 094 094 000 - 69 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 076 050 000 - 24 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 1 235 POR_Recovery_Count -O--C- 099 099 000 - 22 241 Total_LBAs_Written -O--CK 099 099 000 - 28362116562 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 16 Device vendor specific log 0xce GPL,SL VS 16 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/351584 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 128 (7) Index Estimated Time Temperature Celsius 8 2020-10-28 10:30 24 ***** ... ..( 2 skipped). .. ***** 11 2020-10-28 11:00 24 ***** 12 2020-10-28 11:10 25 ****** ... ..( 21 skipped). .. ****** 34 2020-10-28 14:50 25 ****** 35 2020-10-28 15:00 26 ******* ... ..( 45 skipped). .. ******* 81 2020-10-28 22:40 26 ******* 82 2020-10-28 22:50 25 ****** ... ..( 12 skipped). .. ****** 95 2020-10-29 01:00 25 ****** 96 2020-10-29 01:10 24 ***** ... ..( 27 skipped). .. ***** 124 2020-10-29 05:50 24 ***** 125 2020-10-29 06:00 23 **** 126 2020-10-29 06:10 23 **** 127 2020-10-29 06:20 23 **** 0 2020-10-29 06:30 24 ***** ... ..( 6 skipped). .. ***** 7 2020-10-29 07:40 24 ***** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 39 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 39 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/ada1 smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron MX500 SSDs Device Model: CT250MX500SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M3CR023 User Capacity: 250,059,350,016 bytes [250 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 29 07:45:53 2020 GMT ==> WARNING: This firmware returns bogus raw values in attribute 197 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 512 12 Power_Cycle_Count -O--CK 100 100 000 - 3 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Ave_Block-Erase_Count -O--CK 100 100 000 - 12 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 1 180 Unused_Reserve_NAND_Blk PO--CK 000 000 000 - 27 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 065 054 000 - 35 (Min/Max 0/46) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Bogus_Current_Pend_Sect -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 202 Percent_Lifetime_Remain ----CK 100 100 001 - 0 206 Write_Error_Rate -OSR-- 100 100 000 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 1377930222 247 Host_Program_Page_Count -O--CK 100 100 000 - 24377345 248 FTL_Program_Page_Count -O--CK 100 100 000 - 39135767 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 64 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Completed [00% left] (0-65535) Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 26/41 Celsius Lifetime Min/Max Temperature: 0/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: 0/100 Celsius Temperature History Size (Index): 128 (29) Index Estimated Time Temperature Celsius 30 2020-10-29 05:38 33 ************** 31 2020-10-29 05:39 31 ************ 32 2020-10-29 05:40 31 ************ 33 2020-10-29 05:41 33 ************** 34 2020-10-29 05:42 31 ************ 35 2020-10-29 05:43 33 ************** 36 2020-10-29 05:44 33 ************** 37 2020-10-29 05:45 33 ************** 38 2020-10-29 05:46 31 ************ 39 2020-10-29 05:47 33 ************** 40 2020-10-29 05:48 33 ************** 41 2020-10-29 05:49 33 ************** 42 2020-10-29 05:50 31 ************ 43 2020-10-29 05:51 33 ************** ... ..( 6 skipped). .. ************** 50 2020-10-29 05:58 33 ************** 51 2020-10-29 05:59 31 ************ 52 2020-10-29 06:00 31 ************ 53 2020-10-29 06:01 33 ************** 54 2020-10-29 06:02 31 ************ 55 2020-10-29 06:03 33 ************** 56 2020-10-29 06:04 33 ************** 57 2020-10-29 06:05 31 ************ 58 2020-10-29 06:06 31 ************ 59 2020-10-29 06:07 31 ************ 60 2020-10-29 06:08 33 ************** 61 2020-10-29 06:09 33 ************** 62 2020-10-29 06:10 31 ************ 63 2020-10-29 06:11 33 ************** ... ..( 2 skipped). .. ************** 66 2020-10-29 06:14 33 ************** 67 2020-10-29 06:15 31 ************ 68 2020-10-29 06:16 31 ************ 69 2020-10-29 06:17 31 ************ 70 2020-10-29 06:18 33 ************** 71 2020-10-29 06:19 31 ************ 72 2020-10-29 06:20 33 ************** 73 2020-10-29 06:21 31 ************ 74 2020-10-29 06:22 31 ************ 75 2020-10-29 06:23 31 ************ 76 2020-10-29 06:24 33 ************** 77 2020-10-29 06:25 31 ************ ... ..( 2 skipped). .. ************ 80 2020-10-29 06:28 31 ************ 81 2020-10-29 06:29 33 ************** 82 2020-10-29 06:30 31 ************ 83 2020-10-29 06:31 33 ************** 84 2020-10-29 06:32 31 ************ 85 2020-10-29 06:33 33 ************** 86 2020-10-29 06:34 33 ************** 87 2020-10-29 06:35 31 ************ 88 2020-10-29 06:36 33 ************** ... ..( 4 skipped). .. ************** 93 2020-10-29 06:41 33 ************** 94 2020-10-29 06:42 31 ************ ... ..( 2 skipped). .. ************ 97 2020-10-29 06:45 31 ************ 98 2020-10-29 06:46 33 ************** ... ..( 2 skipped). .. ************** 101 2020-10-29 06:49 33 ************** 102 2020-10-29 06:50 31 ************ 103 2020-10-29 06:51 33 ************** 104 2020-10-29 06:52 31 ************ 105 2020-10-29 06:53 33 ************** 106 2020-10-29 06:54 33 ************** 107 2020-10-29 06:55 31 ************ 108 2020-10-29 06:56 33 ************** 109 2020-10-29 06:57 33 ************** 110 2020-10-29 06:58 31 ************ 111 2020-10-29 06:59 33 ************** 112 2020-10-29 07:00 33 ************** 113 2020-10-29 07:01 31 ************ 114 2020-10-29 07:02 33 ************** 115 2020-10-29 07:03 31 ************ 116 2020-10-29 07:04 31 ************ 117 2020-10-29 07:05 33 ************** 118 2020-10-29 07:06 33 ************** 119 2020-10-29 07:07 35 **************** 120 2020-10-29 07:08 33 ************** 121 2020-10-29 07:09 33 ************** 122 2020-10-29 07:10 31 ************ 123 2020-10-29 07:11 33 ************** ... ..( 3 skipped). .. ************** 127 2020-10-29 07:15 33 ************** 0 2020-10-29 07:16 35 **************** 1 2020-10-29 07:17 33 ************** 2 2020-10-29 07:18 33 ************** 3 2020-10-29 07:19 33 ************** 4 2020-10-29 07:20 35 **************** 5 2020-10-29 07:21 33 ************** ... ..( 13 skipped). .. ************** 19 2020-10-29 07:35 33 ************** 20 2020-10-29 07:36 31 ************ 21 2020-10-29 07:37 33 ************** 22 2020-10-29 07:38 35 **************** 23 2020-10-29 07:39 33 ************** 24 2020-10-29 07:40 35 **************** 25 2020-10-29 07:41 33 ************** 26 2020-10-29 07:42 33 ************** 27 2020-10-29 07:43 35 **************** 28 2020-10-29 07:44 33 ************** 29 2020-10-29 07:45 33 ************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3 --- Lifetime Power-On Resets 0x01 0x010 4 512 --- Power-on Hours 0x01 0x018 6 1377930222 --- Logical Sectors Written 0x01 0x020 6 17836086 --- Number of Write Commands 0x01 0x028 6 806217314 --- Logical Sectors Read 0x01 0x030 6 29423728 --- Number of Read Commands 0x01 0x038 6 4294967296 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 34 --- Average Short Term Temperature 0x05 0x018 1 34 --- Average Long Term Temperature 0x05 0x020 1 46 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 40 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 40 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 110 --- Number of Hardware Resets 0x06 0x010 4 18 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 40 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/ada2 smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD60EFRX-68L0BN1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 29 07:45:53 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3164) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 685) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 206 197 021 - 8691 4 Start_Stop_Count -O--CK 100 100 000 - 44 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 098 098 000 - 1742 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 22 192 Power-Off_Retract_Count -O--CK 200 200 000 - 17 193 Load_Cycle_Count -O--CK 200 200 000 - 378 194 Temperature_Celsius -O---K 118 105 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 54 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 4 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 01 19 a5 01 30 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 00:22:44.660 FLUSH CACHE EXT 25 00 00 00 21 00 00 00 00 08 00 e0 00 00:22:32.106 READ DMA EXT 25 00 00 00 80 00 02 ba a0 ee a0 e0 00 00:22:32.104 READ DMA EXT 25 00 00 00 80 00 02 ba a0 ee 20 e0 00 00:22:32.104 READ DMA EXT 25 00 00 00 80 00 02 ba a0 ec a0 e0 00 00:22:32.101 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 00 00 01 19 a5 01 00 e0 00 Error: IDNF 256 sectors at LBA = 0x119a50100 = 4725211392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 01 00 00 01 19 a4 fd 00 e0 00 00:16:05.220 WRITE DMA EXT 35 00 00 01 00 00 01 19 a4 fc 00 e0 00 00:16:05.219 WRITE DMA EXT 35 00 00 01 00 00 01 19 a4 fb 00 e0 00 00:16:05.219 WRITE DMA EXT 35 00 00 01 00 00 01 19 a4 fa 00 e0 00 00:16:05.218 WRITE DMA EXT 35 00 00 01 00 00 01 19 a4 f9 00 e0 00 00:16:05.217 WRITE DMA EXT Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 01 17 f8 58 70 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 00:13:51.227 FLUSH CACHE EXT 25 00 00 00 21 00 00 00 00 08 00 e0 00 00:13:38.492 READ DMA EXT 25 00 00 00 80 00 02 ba a0 ee a0 e0 00 00:13:38.490 READ DMA EXT 25 00 00 00 80 00 02 ba a0 ee 20 e0 00 00:13:38.490 READ DMA EXT 25 00 00 00 80 00 02 ba a0 ec a0 e0 00 00:13:38.487 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 00 00 01 17 f8 57 80 e0 00 Error: IDNF 256 sectors at LBA = 0x117f85780 = 4697118592 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 01 00 00 01 17 f8 57 80 e0 00 00:07:11.803 WRITE DMA EXT 35 00 00 01 00 00 01 17 f8 56 80 e0 00 00:07:11.802 WRITE DMA EXT 35 00 00 01 00 00 01 17 f8 55 80 e0 00 00:07:11.801 WRITE DMA EXT 35 00 00 01 00 00 01 17 f8 54 80 e0 00 00:07:11.800 WRITE DMA EXT 35 00 00 01 00 00 01 17 f8 53 80 e0 00 00:07:11.800 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 33/38 Celsius Lifetime Min/Max Temperature: 22/45 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (323) Index Estimated Time Temperature Celsius 324 2020-10-28 23:48 34 *************** ... ..( 48 skipped). .. *************** 373 2020-10-29 00:37 34 *************** 374 2020-10-29 00:38 36 ***************** ... ..( 26 skipped). .. ***************** 401 2020-10-29 01:05 36 ***************** 402 2020-10-29 01:06 35 **************** ... ..(175 skipped). .. **************** 100 2020-10-29 04:02 35 **************** 101 2020-10-29 04:03 36 ***************** ... ..( 13 skipped). .. ***************** 115 2020-10-29 04:17 36 ***************** 116 2020-10-29 04:18 35 **************** ... ..( 62 skipped). .. **************** 179 2020-10-29 05:21 35 **************** 180 2020-10-29 05:22 36 ***************** ... ..( 38 skipped). .. ***************** 219 2020-10-29 06:01 36 ***************** 220 2020-10-29 06:02 35 **************** ... ..( 52 skipped). .. **************** 273 2020-10-29 06:55 35 **************** 274 2020-10-29 06:56 34 *************** ... ..( 48 skipped). .. *************** 323 2020-10-29 07:45 34 *************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 22 --- Lifetime Power-On Resets 0x01 0x010 4 1742 --- Power-on Hours 0x01 0x018 6 20756993330 --- Logical Sectors Written 0x01 0x020 6 106708446 --- Number of Write Commands 0x01 0x028 6 9703311995 --- Logical Sectors Read 0x01 0x030 6 76447549 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 1664 --- Spindle Motor Power-on Hours 0x03 0x010 4 180 --- Head Flying Hours 0x03 0x018 4 396 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 2 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 65537 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 35 --- Average Short Term Temperature 0x05 0x018 1 35 --- Average Long Term Temperature 0x05 0x020 1 45 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 40 --- Highest Average Short Term Temperature 0x05 0x038 1 25 --- Lowest Average Short Term Temperature 0x05 0x040 1 35 --- Highest Average Long Term Temperature 0x05 0x048 1 35 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 216 --- Number of Hardware Resets 0x06 0x010 4 164 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 39 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 40 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2231692 Vendor specific /dev/ada3 smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-60M2NA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 29 07:45:54 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11400) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 118) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 21 3 Spin_Up_Time POS--K 176 170 021 - 2191 4 Start_Stop_Count -O--CK 100 100 000 - 545 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 097 097 000 - 2413 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 545 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 089 000 - 21 188 Command_Timeout -O--CK 100 099 000 - 4 190 Airflow_Temperature_Cel -O---K 067 053 040 - 33 (Min/Max 32/37) 192 Power-Off_Retract_Count -O--CK 200 200 000 - 5 193 Load_Cycle_Count -O--CK 200 200 000 - 539 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0d GPL,SL R/O 8 LPS Mis-alignment log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 302 Device vendor specific log 0xb6 SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 21 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 21 [20] occurred at disk power-on lifetime: 603 hours (25 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 03 96 af 99 e0 00 Error: UNC 256 sectors at LBA = 0x0396af99 = 60207001 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 03 96 af 99 e0 00 01:56:36.458 READ DMA EXT 35 00 00 00 08 00 00 00 66 0f 20 e0 00 01:56:33.207 WRITE DMA EXT ea 00 00 00 00 66 0f b8 00 00 00 e0 00 01:56:33.142 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 66 0f b0 e0 00 01:56:33.142 WRITE DMA EXT 35 00 00 00 08 00 00 00 8a 50 a0 e0 00 01:56:33.035 WRITE DMA EXT Error 20 [19] occurred at disk power-on lifetime: 603 hours (25 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 96 af 99 e0 00 Error: UNC 1 sectors at LBA = 0x0396af99 = 60207001 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 96 af 99 e0 00 01:56:28.473 READ DMA EXT 35 00 00 00 60 00 00 3a 38 31 00 e0 00 01:56:28.459 WRITE DMA EXT 25 00 00 00 60 00 00 00 67 70 00 e0 00 01:56:28.458 READ DMA EXT 25 00 00 00 01 00 00 03 96 af 98 e0 00 01:56:24.009 READ DMA EXT 35 00 00 00 08 00 00 00 0b 68 18 e0 00 01:56:22.538 WRITE DMA EXT Error 19 [18] occurred at disk power-on lifetime: 603 hours (25 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 96 af 98 e0 00 Error: UNC 1 sectors at LBA = 0x0396af98 = 60207000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 96 af 98 e0 00 01:56:24.009 READ DMA EXT 35 00 00 00 08 00 00 00 0b 68 18 e0 00 01:56:22.538 WRITE DMA EXT 35 00 00 00 20 00 00 3a 38 30 e0 e0 00 01:56:22.538 WRITE DMA EXT 25 00 00 00 20 00 00 00 0b 68 00 e0 00 01:56:22.532 READ DMA EXT 35 00 00 00 08 00 00 04 cf 91 b8 e0 00 01:56:22.531 WRITE DMA EXT Error 18 [17] occurred at disk power-on lifetime: 602 hours (25 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 96 af 98 e0 00 Error: UNC 1 sectors at LBA = 0x0396af98 = 60207000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 96 af 98 e0 00 01:49:57.114 READ DMA EXT 25 00 00 00 01 00 00 03 96 af 97 e0 00 01:49:57.114 READ DMA EXT 25 00 00 00 01 00 00 03 96 af 96 e0 00 01:49:57.113 READ DMA EXT 25 00 00 00 01 00 00 03 96 af 95 e0 00 01:49:57.113 READ DMA EXT 25 00 00 00 01 00 00 03 96 af 94 e0 00 01:49:57.113 READ DMA EXT Error 17 [16] occurred at disk power-on lifetime: 602 hours (25 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 03 96 af 18 e0 00 Error: UNC 256 sectors at LBA = 0x0396af18 = 60206872 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 03 96 af 18 e0 00 01:49:52.452 READ DMA EXT 25 00 00 01 00 00 00 03 96 ae 18 e0 00 01:49:52.451 READ DMA EXT 25 00 00 00 08 00 00 03 96 ae 10 e0 00 01:49:52.450 READ DMA EXT 25 00 00 01 00 00 00 03 96 ad 10 e0 00 01:49:52.449 READ DMA EXT 25 00 00 01 00 00 00 03 96 ac 10 e0 00 01:49:52.449 READ DMA EXT Error 16 [15] occurred at disk power-on lifetime: 602 hours (25 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 96 af 98 e0 00 Error: UNC 1 sectors at LBA = 0x0396af98 = 60207000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 96 af 98 e0 00 01:05:49.697 READ DMA EXT 35 00 00 00 08 00 00 00 66 0f 28 e0 00 01:05:49.422 WRITE DMA EXT ea 00 00 00 00 66 0f b8 00 00 00 e0 00 01:05:49.388 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 66 0f b0 e0 00 01:05:49.388 WRITE DMA EXT 35 00 00 00 60 00 00 00 66 b3 f8 e0 00 01:05:49.343 WRITE DMA EXT Error 15 [14] occurred at disk power-on lifetime: 602 hours (25 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 96 af 98 e0 00 Error: UNC 1 sectors at LBA = 0x0396af98 = 60207000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 96 af 98 e0 00 01:05:39.679 READ DMA EXT 25 00 00 00 28 00 00 06 8d 85 0a e0 00 01:05:39.665 READ DMA EXT 35 00 00 00 08 00 00 00 66 0f 20 e0 00 01:05:36.831 WRITE DMA EXT ea 00 00 00 00 66 0f b8 00 00 00 e0 00 01:05:36.804 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 66 0f b0 e0 00 01:05:36.804 WRITE DMA EXT Error 14 [13] occurred at disk power-on lifetime: 602 hours (25 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 03 96 af 98 e0 00 Error: UNC 1 sectors at LBA = 0x0396af98 = 60207000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 03 96 af 98 e0 00 01:05:16.651 READ DMA EXT 25 00 00 00 40 00 00 06 a7 56 22 e0 00 01:05:16.629 READ DMA EXT 25 00 00 00 40 00 00 3a 62 f4 a2 e0 00 01:05:16.627 READ DMA EXT 25 00 00 00 40 00 00 3a 63 22 ba e0 00 01:05:16.619 READ DMA EXT 25 00 00 00 40 00 00 3a 63 23 8a e0 00 01:05:16.608 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 32/37 Celsius Lifetime Min/Max Temperature: 12/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (19) Index Estimated Time Temperature Celsius 20 2020-10-29 05:38 33 ************** ... ..(126 skipped). .. ************** 19 2020-10-29 07:45 33 ************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 39 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 40 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2231787 Vendor specific