/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p3 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD20EFRX-68EUZN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 22 08:25:26 2021 MST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 266) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 176 173 021 - 4200 4 Start_Stop_Count -O--CK 100 100 000 - 293 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 028 028 000 - 52613 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 293 192 Power-Off_Retract_Count -O--CK 200 200 000 - 194 193 Load_Cycle_Count -O--CK 199 199 000 - 4515 194 Temperature_Celsius -O---K 117 102 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 52471 - # 2 Extended offline Completed without error 00% 52303 - # 3 Extended offline Completed without error 00% 52135 - # 4 Extended offline Completed without error 00% 51969 - # 5 Extended offline Completed without error 00% 51798 - # 6 Extended offline Completed without error 00% 51633 - # 7 Extended offline Completed without error 00% 51463 - # 8 Extended offline Interrupted (host reset) 10% 51299 - # 9 Extended offline Completed without error 00% 51128 - #10 Extended offline Completed without error 00% 50962 - #11 Extended offline Completed without error 00% 50792 - #12 Extended offline Completed without error 00% 50624 - #13 Extended offline Interrupted (host reset) 10% 50454 - #14 Extended offline Completed without error 00% 50289 - #15 Extended offline Completed without error 00% 50122 - #16 Extended offline Completed without error 00% 49955 - #17 Extended offline Completed without error 00% 49785 - #18 Extended offline Completed without error 00% 49620 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 26/36 Celsius Lifetime Min/Max Temperature: 21/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (182) Index Estimated Time Temperature Celsius 183 2021-02-22 00:28 30 *********** ... ..( 55 skipped). .. *********** 239 2021-02-22 01:24 30 *********** 240 2021-02-22 01:25 29 ********** ... ..(107 skipped). .. ********** 348 2021-02-22 03:13 29 ********** 349 2021-02-22 03:14 30 *********** ... ..( 4 skipped). .. *********** 354 2021-02-22 03:19 30 *********** 355 2021-02-22 03:20 31 ************ ... ..( 39 skipped). .. ************ 395 2021-02-22 04:00 31 ************ 396 2021-02-22 04:01 32 ************* 397 2021-02-22 04:02 32 ************* 398 2021-02-22 04:03 32 ************* 399 2021-02-22 04:04 31 ************ ... ..( 11 skipped). .. ************ 411 2021-02-22 04:16 31 ************ 412 2021-02-22 04:17 30 *********** ... ..( 28 skipped). .. *********** 441 2021-02-22 04:46 30 *********** 442 2021-02-22 04:47 29 ********** 443 2021-02-22 04:48 29 ********** 444 2021-02-22 04:49 29 ********** 445 2021-02-22 04:50 30 *********** ... ..( 18 skipped). .. *********** 464 2021-02-22 05:09 30 *********** 465 2021-02-22 05:10 29 ********** ... ..( 46 skipped). .. ********** 34 2021-02-22 05:57 29 ********** 35 2021-02-22 05:58 28 ********* ... ..( 43 skipped). .. ********* 79 2021-02-22 06:42 28 ********* 80 2021-02-22 06:43 29 ********** ... ..( 6 skipped). .. ********** 87 2021-02-22 06:50 29 ********** 88 2021-02-22 06:51 30 *********** ... ..( 8 skipped). .. *********** 97 2021-02-22 07:00 30 *********** 98 2021-02-22 07:01 29 ********** ... ..( 9 skipped). .. ********** 108 2021-02-22 07:11 29 ********** 109 2021-02-22 07:12 30 *********** ... ..( 2 skipped). .. *********** 112 2021-02-22 07:15 30 *********** 113 2021-02-22 07:16 29 ********** 114 2021-02-22 07:17 30 *********** ... ..( 49 skipped). .. *********** 164 2021-02-22 08:07 30 *********** 165 2021-02-22 08:08 29 ********** ... ..( 11 skipped). .. ********** 177 2021-02-22 08:20 29 ********** 178 2021-02-22 08:21 30 *********** ... ..( 3 skipped). .. *********** 182 2021-02-22 08:25 30 *********** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 11 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 12 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 4204020 Vendor specific /dev/ada1 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p3 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD20EFRX-68EUZN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 22 08:25:26 2021 MST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x05) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25980) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 263) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 176 173 021 - 4200 4 Start_Stop_Count -O--CK 100 100 000 - 357 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 023 023 000 - 56813 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 357 192 Power-Off_Retract_Count -O--CK 200 200 000 - 252 193 Load_Cycle_Count -O--CK 198 198 000 - 6790 194 Temperature_Celsius -O---K 112 100 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 56672 - # 2 Extended offline Completed without error 00% 56503 - # 3 Extended offline Completed without error 00% 56335 - # 4 Extended offline Completed without error 00% 56169 - # 5 Extended offline Completed without error 00% 55999 - # 6 Extended offline Completed without error 00% 55833 - # 7 Extended offline Completed without error 00% 55664 - # 8 Extended offline Interrupted (host reset) 10% 55499 - # 9 Extended offline Completed without error 00% 55328 - #10 Extended offline Completed without error 00% 55163 - #11 Extended offline Completed without error 00% 54993 - #12 Extended offline Completed without error 00% 54825 - #13 Extended offline Interrupted (host reset) 10% 54654 - #14 Extended offline Completed without error 00% 54490 - #15 Extended offline Completed without error 00% 54323 - #16 Extended offline Completed without error 00% 54156 - #17 Extended offline Completed without error 00% 53986 - #18 Extended offline Completed without error 00% 53821 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 29/41 Celsius Lifetime Min/Max Temperature: 18/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (136) Index Estimated Time Temperature Celsius 137 2021-02-22 00:28 34 *************** ... ..( 10 skipped). .. *************** 148 2021-02-22 00:39 34 *************** 149 2021-02-22 00:40 33 ************** ... ..( 13 skipped). .. ************** 163 2021-02-22 00:54 33 ************** 164 2021-02-22 00:55 32 ************* ... ..( 67 skipped). .. ************* 232 2021-02-22 02:03 32 ************* 233 2021-02-22 02:04 33 ************** ... ..( 6 skipped). .. ************** 240 2021-02-22 02:11 33 ************** 241 2021-02-22 02:12 34 *************** ... ..( 50 skipped). .. *************** 292 2021-02-22 03:03 34 *************** 293 2021-02-22 03:04 35 **************** ... ..( 14 skipped). .. **************** 308 2021-02-22 03:19 35 **************** 309 2021-02-22 03:20 34 *************** ... ..( 28 skipped). .. *************** 338 2021-02-22 03:49 34 *************** 339 2021-02-22 03:50 35 **************** ... ..( 6 skipped). .. **************** 346 2021-02-22 03:57 35 **************** 347 2021-02-22 03:58 34 *************** ... ..( 51 skipped). .. *************** 399 2021-02-22 04:50 34 *************** 400 2021-02-22 04:51 33 ************** ... ..(101 skipped). .. ************** 24 2021-02-22 06:33 33 ************** 25 2021-02-22 06:34 34 *************** ... ..( 3 skipped). .. *************** 29 2021-02-22 06:38 34 *************** 30 2021-02-22 06:39 35 **************** ... ..( 5 skipped). .. **************** 36 2021-02-22 06:45 35 **************** 37 2021-02-22 06:46 36 ***************** ... ..( 10 skipped). .. ***************** 48 2021-02-22 06:57 36 ***************** 49 2021-02-22 06:58 37 ****************** ... ..( 26 skipped). .. ****************** 76 2021-02-22 07:25 37 ****************** 77 2021-02-22 07:26 36 ***************** ... ..( 11 skipped). .. ***************** 89 2021-02-22 07:38 36 ***************** 90 2021-02-22 07:39 35 **************** ... ..( 8 skipped). .. **************** 99 2021-02-22 07:48 35 **************** 100 2021-02-22 07:49 34 *************** ... ..( 35 skipped). .. *************** 136 2021-02-22 08:25 34 *************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 4204025 Vendor specific /dev/ada2 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p3 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD20EFRX-68EUZN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 22 08:25:26 2021 MST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x05) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26580) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 268) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 51 3 Spin_Up_Time POS--K 178 175 021 - 4066 4 Start_Stop_Count -O--CK 100 100 000 - 293 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 028 028 000 - 52613 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 293 192 Power-Off_Retract_Count -O--CK 200 200 000 - 196 193 Load_Cycle_Count -O--CK 199 199 000 - 4520 194 Temperature_Celsius -O---K 113 101 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 25 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 25 [0] occurred at disk power-on lifetime: 34178 hours (1424 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 c9 36 f0 40 00 Error: WP at LBA = 0x00c936f0 = 13186800 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 00 00 00 53 d4 4c 38 40 08 11d+15:27:24.200 WRITE FPDMA QUEUED 60 01 00 00 f8 00 00 00 c9 44 30 40 08 11d+15:27:24.200 READ FPDMA QUEUED 60 01 00 00 f0 00 00 00 c9 43 30 40 08 11d+15:27:24.200 READ FPDMA QUEUED 60 01 00 00 e8 00 00 00 c9 42 30 40 08 11d+15:27:24.200 READ FPDMA QUEUED 60 01 00 00 e0 00 00 00 c9 41 30 40 08 11d+15:27:24.200 READ FPDMA QUEUED Error 24 [23] occurred at disk power-on lifetime: 34178 hours (1424 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 c9 36 f0 40 00 Error: WP at LBA = 0x00c936f0 = 13186800 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 78 00 00 53 d4 4c 38 40 08 11d+15:27:20.691 WRITE FPDMA QUEUED 60 01 00 00 70 00 00 00 c9 44 30 40 08 11d+15:27:20.691 READ FPDMA QUEUED 60 01 00 00 68 00 00 00 c9 43 30 40 08 11d+15:27:20.691 READ FPDMA QUEUED 60 01 00 00 60 00 00 00 c9 42 30 40 08 11d+15:27:20.691 READ FPDMA QUEUED 60 01 00 00 58 00 00 00 c9 41 30 40 08 11d+15:27:20.691 READ FPDMA QUEUED Error 23 [22] occurred at disk power-on lifetime: 34178 hours (1424 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 c9 36 f0 40 00 Error: WP at LBA = 0x00c936f0 = 13186800 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 f0 00 00 53 d4 4c 38 40 08 11d+15:27:17.192 WRITE FPDMA QUEUED 60 01 00 00 e8 00 00 00 c9 44 30 40 08 11d+15:27:17.192 READ FPDMA QUEUED 60 01 00 00 e0 00 00 00 c9 43 30 40 08 11d+15:27:17.192 READ FPDMA QUEUED 60 01 00 00 d8 00 00 00 c9 42 30 40 08 11d+15:27:17.192 READ FPDMA QUEUED 60 01 00 00 d0 00 00 00 c9 41 30 40 08 11d+15:27:17.192 READ FPDMA QUEUED Error 22 [21] occurred at disk power-on lifetime: 34178 hours (1424 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 c9 36 f0 40 00 Error: WP at LBA = 0x00c936f0 = 13186800 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 68 00 00 53 d4 4c 38 40 08 11d+15:27:13.695 WRITE FPDMA QUEUED 60 01 00 00 60 00 00 00 c9 44 30 40 08 11d+15:27:13.695 READ FPDMA QUEUED 60 01 00 00 58 00 00 00 c9 43 30 40 08 11d+15:27:13.695 READ FPDMA QUEUED 60 01 00 00 50 00 00 00 c9 42 30 40 08 11d+15:27:13.695 READ FPDMA QUEUED 60 01 00 00 48 00 00 00 c9 41 30 40 08 11d+15:27:13.695 READ FPDMA QUEUED Error 21 [20] occurred at disk power-on lifetime: 34178 hours (1424 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 c9 36 f0 40 00 Error: UNC at LBA = 0x00c936f0 = 13186800 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 c0 00 00 00 c9 40 30 40 08 11d+15:27:10.221 READ FPDMA QUEUED 60 01 00 00 b8 00 00 00 c9 3f 30 40 08 11d+15:27:10.221 READ FPDMA QUEUED 60 01 00 00 b0 00 00 00 c9 3e 30 40 08 11d+15:27:10.221 READ FPDMA QUEUED 60 01 00 00 a8 00 00 00 c9 3d 30 40 08 11d+15:27:10.221 READ FPDMA QUEUED 60 01 00 00 a0 00 00 00 c9 3c 30 40 08 11d+15:27:10.213 READ FPDMA QUEUED Error 20 [19] occurred at disk power-on lifetime: 30115 hours (1254 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d8 47 2b 38 40 00 Error: UNC at LBA = 0xd8472b38 = 3628542776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 d8 00 00 d8 47 2a 60 40 08 04:01:34.430 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 04:01:34.429 READ LOG EXT 60 01 00 00 c8 00 00 d8 47 2a 60 40 08 04:01:30.900 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 04:01:30.900 READ LOG EXT 60 01 00 00 b8 00 00 d8 47 2a 60 40 08 04:01:27.370 READ FPDMA QUEUED Error 19 [18] occurred at disk power-on lifetime: 30115 hours (1254 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d8 47 2b 38 40 00 Error: UNC at LBA = 0xd8472b38 = 3628542776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 c8 00 00 d8 47 2a 60 40 08 04:01:30.900 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 04:01:30.900 READ LOG EXT 60 01 00 00 b8 00 00 d8 47 2a 60 40 08 04:01:27.370 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 04:01:27.370 READ LOG EXT 61 00 08 00 a8 00 00 d6 48 2e 30 40 08 04:01:23.830 WRITE FPDMA QUEUED Error 18 [17] occurred at disk power-on lifetime: 30115 hours (1254 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d8 47 2b 38 40 00 Error: UNC at LBA = 0xd8472b38 = 3628542776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 b8 00 00 d8 47 2a 60 40 08 04:01:27.370 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 04:01:27.370 READ LOG EXT 61 00 08 00 a8 00 00 d6 48 2e 30 40 08 04:01:23.830 WRITE FPDMA QUEUED 61 00 80 00 a0 00 00 d6 47 dd b0 40 08 04:01:23.830 WRITE FPDMA QUEUED 61 00 a0 00 98 00 00 d6 48 37 50 40 08 04:01:23.829 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 52473 - # 2 Extended offline Completed without error 00% 52304 - # 3 Extended offline Completed without error 00% 52137 - # 4 Extended offline Completed without error 00% 51970 - # 5 Extended offline Completed without error 00% 51801 - # 6 Extended offline Completed without error 00% 51634 - # 7 Extended offline Completed without error 00% 51465 - # 8 Extended offline Interrupted (host reset) 10% 51299 - # 9 Extended offline Completed without error 00% 51130 - #10 Extended offline Completed without error 00% 50964 - #11 Extended offline Completed without error 00% 50796 - #12 Extended offline Completed without error 00% 50626 - #13 Extended offline Interrupted (host reset) 50% 50453 - #14 Extended offline Completed without error 00% 50290 - #15 Extended offline Completed without error 00% 50123 - #16 Extended offline Completed without error 00% 49957 - #17 Extended offline Completed without error 00% 49787 - #18 Extended offline Completed without error 00% 49622 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 29/40 Celsius Lifetime Min/Max Temperature: 22/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (142) Index Estimated Time Temperature Celsius 143 2021-02-22 00:28 34 *************** ... ..( 39 skipped). .. *************** 183 2021-02-22 01:08 34 *************** 184 2021-02-22 01:09 33 ************** ... ..(124 skipped). .. ************** 309 2021-02-22 03:14 33 ************** 310 2021-02-22 03:15 34 *************** ... ..( 3 skipped). .. *************** 314 2021-02-22 03:19 34 *************** 315 2021-02-22 03:20 35 **************** ... ..( 6 skipped). .. **************** 322 2021-02-22 03:27 35 **************** 323 2021-02-22 03:28 36 ***************** ... ..( 46 skipped). .. ***************** 370 2021-02-22 04:15 36 ***************** 371 2021-02-22 04:16 35 **************** ... ..( 5 skipped). .. **************** 377 2021-02-22 04:22 35 **************** 378 2021-02-22 04:23 34 *************** ... ..( 48 skipped). .. *************** 427 2021-02-22 05:12 34 *************** 428 2021-02-22 05:13 33 ************** ... ..( 12 skipped). .. ************** 441 2021-02-22 05:26 33 ************** 442 2021-02-22 05:27 32 ************* ... ..( 75 skipped). .. ************* 40 2021-02-22 06:43 32 ************* 41 2021-02-22 06:44 33 ************** ... ..( 5 skipped). .. ************** 47 2021-02-22 06:50 33 ************** 48 2021-02-22 06:51 34 *************** ... ..( 8 skipped). .. *************** 57 2021-02-22 07:00 34 *************** 58 2021-02-22 07:01 33 ************** ... ..( 8 skipped). .. ************** 67 2021-02-22 07:10 33 ************** 68 2021-02-22 07:11 34 *************** ... ..( 73 skipped). .. *************** 142 2021-02-22 08:25 34 *************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 4204012 Vendor specific /dev/da0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p3 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Laptop HDD Device Model: ST500LT012-1DG142 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0002LVM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 22 08:25:27 2021 MST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 100) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 115 099 034 - 87047720 3 Spin_Up_Time PO---- 100 099 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 366 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 073 060 030 - 25074212 9 Power_On_Hours -O--CK 094 094 000 - 5424 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 361 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 074 045 045 Past 26 (Min/Max 25/27) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 15 192 Power-Off_Retract_Count -O--CK 100 100 000 - 84 193 Load_Cycle_Count -O--CK 100 100 000 - 1706 194 Temperature_Celsius -O---K 026 055 000 - 26 (0 17 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbd-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 18 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 25/26 Celsius Lifetime Min/Max Temperature: 17/55 Celsius Under/Over Temperature Limit Count: 0/2 Vendor specific: 00 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 11 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (38) Index Estimated Time Temperature Celsius 39 2021-02-21 08:58 44 ************************* ... ..( 19 skipped). .. ************************* 59 2021-02-21 12:38 44 ************************* 60 2021-02-21 12:49 43 ************************ 61 2021-02-21 13:00 43 ************************ 62 2021-02-21 13:11 44 ************************* ... ..( 2 skipped). .. ************************* 65 2021-02-21 13:44 44 ************************* 66 2021-02-21 13:55 43 ************************ 67 2021-02-21 14:06 43 ************************ 68 2021-02-21 14:17 43 ************************ 69 2021-02-21 14:28 44 ************************* 70 2021-02-21 14:39 43 ************************ 71 2021-02-21 14:50 43 ************************ 72 2021-02-21 15:01 44 ************************* 73 2021-02-21 15:12 44 ************************* 74 2021-02-21 15:23 44 ************************* 75 2021-02-21 15:34 ? - 76 2021-02-21 15:45 36 ***************** 77 2021-02-21 15:56 40 ********************* 78 2021-02-21 16:07 ? - 79 2021-02-21 16:18 42 *********************** 80 2021-02-21 16:29 ? - 81 2021-02-21 16:40 41 ********************** 82 2021-02-21 16:51 ? - 83 2021-02-21 17:02 43 ************************ 84 2021-02-21 17:13 ? - 85 2021-02-21 17:24 23 **** 86 2021-02-21 17:35 32 ************* 87 2021-02-21 17:46 35 **************** 88 2021-02-21 17:57 36 ***************** 89 2021-02-21 18:08 36 ***************** 90 2021-02-21 18:19 37 ****************** ... ..( 18 skipped). .. ****************** 109 2021-02-21 21:48 37 ****************** 110 2021-02-21 21:59 36 ***************** ... ..( 25 skipped). .. ***************** 8 2021-02-22 02:45 36 ***************** 9 2021-02-22 02:56 35 **************** ... ..( 20 skipped). .. **************** 30 2021-02-22 06:47 35 **************** 31 2021-02-22 06:58 34 *************** 32 2021-02-22 07:09 35 **************** 33 2021-02-22 07:20 34 *************** 34 2021-02-22 07:31 ? - 35 2021-02-22 07:42 26 ******* 36 2021-02-22 07:53 ? - 37 2021-02-22 08:04 26 ******* 38 2021-02-22 08:15 25 ****** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS