/dev/sd0c smartctl 7.2 2020-12-30 r5155 [OpenBSD 7.0 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA MK1629GSGF Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: PT000D User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Mar 12 14:06:46 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 112) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 109) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 128 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 094 050 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1409 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 29 9 Power_On_Hours 0x0032 079 079 000 Old_age Always - 521731 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 7580 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 194 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 418 193 Load_Cycle_Count 0x0032 091 091 000 Old_age Always - 97964 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 39 (Min/Max 11/65) 199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 97517238 200 Multi_Zone_Error_Rate 0x0032 100 100 000 Old_age Always - 156308611 240 Head_Flying_Hours 0x0032 082 082 000 Old_age Always - 452832 241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 12053550871 242 Total_LBAs_Read 0x0032 100 100 000 Old_age Always - 30662825980 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 271 SMART Error Log Version: 1 ATA Error Count: 50185 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 50185 occurred at disk power-on lifetime: 8327 hours (346 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 0a c8 de b7 69 Error: UNC at LBA = 0x09b7dec8 = 163045064 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 10 01 df b7 40 00 00:31:29.878 READ FPDMA QUEUED 60 00 08 01 de b7 40 00 00:31:29.878 READ FPDMA QUEUED ef 02 00 00 00 00 00 00 00:31:29.708 SET FEATURES [Enable write cache] aa aa aa aa aa aa aa ff 00:31:29.498 [RESERVED] 60 00 10 01 df b7 40 00 00:31:25.478 READ FPDMA QUEUED Error 50184 occurred at disk power-on lifetime: 8327 hours (346 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 0a c8 de b7 69 Error: UNC at LBA = 0x09b7dec8 = 163045064 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 10 01 df b7 40 00 00:31:25.478 READ FPDMA QUEUED 60 00 08 01 de b7 40 00 00:31:25.478 READ FPDMA QUEUED ef 02 00 00 00 00 00 00 00:31:25.308 SET FEATURES [Enable write cache] aa aa aa aa aa aa aa ff 00:31:25.098 [RESERVED] 60 00 10 01 df b7 40 00 00:31:21.067 READ FPDMA QUEUED Error 50183 occurred at disk power-on lifetime: 8327 hours (346 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 0a c8 de b7 69 Error: UNC at LBA = 0x09b7dec8 = 163045064 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 10 01 df b7 40 00 00:31:21.067 READ FPDMA QUEUED 60 00 08 01 de b7 40 00 00:31:21.067 READ FPDMA QUEUED ef 02 00 00 00 00 00 00 00:31:20.894 SET FEATURES [Enable write cache] aa aa aa aa aa aa aa ff 00:31:20.687 [RESERVED] 60 00 10 01 df b7 40 00 00:31:16.656 READ FPDMA QUEUED Error 50182 occurred at disk power-on lifetime: 8327 hours (346 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 0a c8 de b7 69 Error: UNC at LBA = 0x09b7dec8 = 163045064 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 10 01 df b7 40 00 00:31:16.656 READ FPDMA QUEUED 60 00 08 01 de b7 40 00 00:31:16.656 READ FPDMA QUEUED ef 02 00 00 00 00 00 00 00:31:16.494 SET FEATURES [Enable write cache] aa aa aa aa aa aa aa ff 00:31:16.276 [RESERVED] 60 00 10 01 df b7 40 00 00:31:12.256 READ FPDMA QUEUED Error 50181 occurred at disk power-on lifetime: 8327 hours (346 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 0a c8 de b7 69 Error: UNC at LBA = 0x09b7dec8 = 163045064 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 10 01 df b7 40 00 00:31:12.256 READ FPDMA QUEUED 60 00 08 01 de b7 40 00 00:31:12.256 READ FPDMA QUEUED ef 02 00 00 00 00 00 00 00:31:12.095 SET FEATURES [Enable write cache] aa aa aa aa aa aa aa ff 00:31:11.876 [RESERVED] 60 00 10 01 df b7 40 00 00:31:07.956 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 00% 2558 74098799 # 2 Extended offline Aborted by host 10% 2553 - # 3 Short offline Completed without error 00% 2550 - # 4 Short offline Completed without error 00% 2550 - # 5 Short offline Completed: read failure 00% 2084 39941344 # 6 Short offline Completed: read failure 00% 1336 377777 # 7 Short offline Aborted by host 90% 395 - # 8 Short offline Aborted by host 90% 395 - # 9 Short offline Completed without error 00% 209 - #10 Short offline Aborted by host 90% 3 - #11 Extended offline Aborted by host 80% 0 - #12 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. /dev/sd1c smartctl 7.2 2020-12-30 r5155 [OpenBSD 7.0 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: OPENBSD Product: SR CRYPTO Revision: 006 User Capacity: 7,842,996,224 bytes [7.84 GB] Logical block size: 512 bytes >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.