/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: PNY CS900 250GB SSD Serial Number: -- LU WWN Device Id: 5 f8db4c ... Firmware Version: CS900KB3 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Feb 3 22:06:29 2022 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 5141 12 Power_Cycle_Count -O--C- 100 100 000 - 2344 168 Unknown_Attribute -O--C- 100 100 000 - 0 170 Unknown_Attribute PO---- 086 086 010 - 34 173 Unknown_Attribute -O--C- 100 100 000 - 2752581 192 Power-Off_Retract_Count -O--C- 100 100 000 - 225 194 Temperature_Celsius PO---K 067 067 000 - 33 (Min/Max 33/33) 218 Unknown_Attribute PO-R-- 100 100 050 - 6399 231 Unknown_SSD_Attribute PO--C- 100 100 000 - 95 241 Total_LBAs_Written -O--C- 100 100 000 - 3483 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 304 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 304 [47] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 02 00 00 00 00 66 e8 08 40 00 Error: ICRC, ABRT 512 sectors at LBA = 0x0066e808 = 6744072 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 02 00 00 00 00 66 e8 08 40 00 00:00:00.000 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable read look-ahead] ef 00 03 00 46 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Set transfer mode] Error 303 [46] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 80 00 00 00 c6 40 b8 40 00 Error: ICRC, ABRT 384 sectors at LBA = 0x00c640b8 = 12992696 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 80 00 00 00 c6 40 b8 40 00 00:00:00.000 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable read look-ahead] ef 00 03 00 46 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Set transfer mode] Error 302 [45] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 80 00 00 00 c6 40 b8 40 00 Error: ICRC, ABRT 384 sectors at LBA = 0x00c640b8 = 12992696 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 80 00 00 00 c6 40 b8 40 00 00:00:00.000 READ DMA EXT 25 00 00 02 00 00 00 00 c6 3e b8 40 00 00:00:00.000 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable read look-ahead] Error 301 [44] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 00 e6 17 78 40 00 Error: ICRC, ABRT 256 sectors at LBA = 0x00e61778 = 15079288 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 00 e6 17 78 40 00 00:00:00.000 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:00:00.000 READ LOG EXT 60 01 00 00 b8 00 00 00 e6 17 78 40 00 00:00:00.000 READ FPDMA QUEUED 60 01 00 00 b0 00 00 00 e6 15 d8 40 00 00:00:00.000 READ FPDMA QUEUED 60 00 08 00 a8 00 00 00 e5 8f 98 40 00 00:00:00.000 READ FPDMA QUEUED Error 300 [43] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 05 00 00 00 01 12 4b b8 40 00 Error: ICRC, ABRT 1280 sectors at LBA = 0x01124bb8 = 17976248 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 05 00 00 00 01 12 4b b8 40 00 00:00:00.000 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable read look-ahead] ef 00 03 00 46 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Set transfer mode] Error 299 [42] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 58 00 00 00 ef 30 00 40 00 Error: ICRC, ABRT 88 sectors at LBA = 0x00ef3000 = 15675392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 58 00 00 00 ef 30 00 40 00 00:00:00.000 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable read look-ahead] ef 00 03 00 46 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Set transfer mode] Error 298 [41] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 08 00 00 00 01 04 95 28 40 00 Error: ICRC, ABRT 2048 sectors at LBA = 0x01049528 = 17077544 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 01 04 95 28 40 00 00:00:00.000 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable read look-ahead] ef 00 03 00 46 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Set transfer mode] Error 297 [40] occurred at disk power-on lifetime: 27 hours (1 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 04 00 00 00 00 df 77 c8 40 00 Error: ICRC, ABRT 1024 sectors at LBA = 0x00df77c8 = 14645192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 00 00 00 00 df 77 c8 40 00 00:00:00.000 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Enable read look-ahead] ef 00 03 00 46 00 00 00 00 00 00 00 00 00:00:00.000 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2344 --- Lifetime Power-On Resets 0x01 0x010 4 5141 --- Power-on Hours 0x01 0x018 6 7306232583 --- Logical Sectors Written 0x01 0x028 6 4654860624 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 6399 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 4 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 18 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 12 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/ada1 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.B Device Model: Hitachi HDT721010SLA360 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: ST6OA31B User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Feb 3 22:06:29 2022 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14090) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 235) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 65536 2 Throughput_Performance P-S--- 131 131 054 - 118 3 Spin_Up_Time POS--- 140 140 024 - 395 (Average 426) 4 Start_Stop_Count -O--C- 097 097 000 - 14571 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 1 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 125 125 020 - 33 9 Power_On_Hours -O--C- 094 094 000 - 43294 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3090 192 Power-Off_Retract_Count -O--CK 087 087 000 - 15787 193 Load_Cycle_Count -O--C- 087 087 000 - 15787 194 Temperature_Celsius -O---- 146 146 000 - 41 (Min/Max 14/58) 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 27/43 Celsius Lifetime Min/Max Temperature: 14/58 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (7) Index Estimated Time Temperature Celsius 8 2022-02-03 19:59 42 *********************** ... ..( 5 skipped). .. *********************** 14 2022-02-03 20:05 42 *********************** 15 2022-02-03 20:06 41 ********************** ... ..(119 skipped). .. ********************** 7 2022-02-03 22:06 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 13 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/ada2 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-08M2NA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Feb 3 22:06:30 2022 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10740) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 112) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 5 3 Spin_Up_Time POS--K 175 170 021 - 2225 4 Start_Stop_Count -O--CK 092 092 000 - 8001 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 075 075 000 - 18961 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4787 192 Power-Off_Retract_Count -O--CK 198 198 000 - 2058 193 Load_Cycle_Count -O--CK 198 198 000 - 6114 194 Temperature_Celsius -O---K 108 101 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [4] occurred at disk power-on lifetime: 13467 hours (561 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 c7 ce 28 40 00 Error: UNC at LBA = 0x19c7ce28 = 432524840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 98 00 00 19 c7 ce 28 40 08 00:00:52.481 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 00:00:52.481 READ LOG EXT 60 00 40 00 88 00 00 19 c7 ce 28 40 08 00:00:48.952 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 00:00:48.951 READ LOG EXT 60 00 40 00 78 00 00 19 c7 ce 28 40 08 00:00:45.422 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 13467 hours (561 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 c7 ce 28 40 00 Error: UNC at LBA = 0x19c7ce28 = 432524840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 88 00 00 19 c7 ce 28 40 08 00:00:48.952 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 00:00:48.951 READ LOG EXT 60 00 40 00 78 00 00 19 c7 ce 28 40 08 00:00:45.422 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 00:00:45.422 READ LOG EXT 60 00 40 00 68 00 00 19 c7 ce 28 40 08 00:00:41.901 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 13467 hours (561 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 c7 ce 28 40 00 Error: UNC at LBA = 0x19c7ce28 = 432524840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 78 00 00 19 c7 ce 28 40 08 00:00:45.422 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 00:00:45.422 READ LOG EXT 60 00 40 00 68 00 00 19 c7 ce 28 40 08 00:00:41.901 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 00:00:41.901 READ LOG EXT 60 00 40 00 58 00 00 19 c7 ce 28 40 08 00:00:38.380 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 13467 hours (561 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 c7 ce 28 40 00 Error: UNC at LBA = 0x19c7ce28 = 432524840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 68 00 00 19 c7 ce 28 40 08 00:00:41.901 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 00:00:41.901 READ LOG EXT 60 00 40 00 58 00 00 19 c7 ce 28 40 08 00:00:38.380 READ FPDMA QUEUED 60 00 40 00 50 00 00 05 86 ff 68 40 08 00:00:38.361 READ FPDMA QUEUED 60 00 40 00 48 00 00 04 13 39 28 40 08 00:00:38.361 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 13467 hours (561 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 c7 ce 28 40 00 Error: UNC at LBA = 0x19c7ce28 = 432524840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 58 00 00 19 c7 ce 28 40 08 00:00:38.380 READ FPDMA QUEUED 60 00 40 00 50 00 00 05 86 ff 68 40 08 00:00:38.361 READ FPDMA QUEUED 60 00 40 00 48 00 00 04 13 39 28 40 08 00:00:38.361 READ FPDMA QUEUED 60 00 40 00 40 00 00 4f 95 e2 68 40 08 00:00:38.360 READ FPDMA QUEUED 60 00 40 00 38 00 00 4f 95 df 28 40 08 00:00:38.360 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Vendor (0x50) Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 26/35 Celsius Lifetime Min/Max Temperature: 18/42 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (236) Index Estimated Time Temperature Celsius 237 2022-02-03 14:09 34 *************** ... ..( 55 skipped). .. *************** 293 2022-02-03 15:05 34 *************** 294 2022-02-03 15:06 35 **************** ... ..(313 skipped). .. **************** 130 2022-02-03 20:20 35 **************** 131 2022-02-03 20:21 33 ************** ... ..( 9 skipped). .. ************** 141 2022-02-03 20:31 33 ************** 142 2022-02-03 20:32 34 *************** ... ..( 93 skipped). .. *************** 236 2022-02-03 22:06 34 *************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 48191 Vendor specific /dev/ada3 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST1000DM003-1CH162 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC44 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Feb 3 22:06:30 2022 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 575) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 105) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 099 006 - 80049992 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 095 095 020 - 5271 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 082 060 030 - 196455984 9 Power_On_Hours -O--CK 077 077 000 - 20447 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4343 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 099 000 - 0 0 6 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 062 049 045 - 38 (0 18 38 26 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 3464 193 Load_Cycle_Count -O--CK 056 056 000 - 88336 194 Temperature_Celsius -O---K 038 051 000 - 38 (128 0 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 11711h+55m+18.161s 241 Total_LBAs_Written ------ 100 253 000 - 32576191861 242 Total_LBAs_Read ------ 100 253 000 - 31390405777 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 26/26 Celsius Lifetime Min/Max Temperature: 18/51 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS