/dev/da0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SAMSUNG Product: MZILT3T8HALS0D3 Revision: DSF8 Compliance: SPC-5 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5002538b101e37b0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:48 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current temperature = 20 Lifetime maximum temperature = 42 Lifetime minimum temperature = 15 Maximum temperature since power on = 27 Minimum temperature since power on = 18 Manufactured in week 05 of year 2020 Accumulated start-stop cycles: 17 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 121187.463 0 write: 0 0 0 0 0 97808.710 0 verify: 0 0 0 0 0 3.274 0 Non-medium error count: 69 Pending defect count:0 Pending Defects SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 96 2 - [- - -] # 2 Background short Completed 96 1 - [- - -] Long (extended) Self-test duration: 3600 seconds [60.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 26184:52 [1571092 minutes] Number of background scans performed: 38, scan progress: 82.74% Number of background medium scans performed: 38 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5002538b101e37b2 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 0 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 4130051 Received SSP frame error count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5002538b101e37b3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 /dev/da1 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SAMSUNG Product: MZILT3T8HALS0D3 Revision: DSF8 Compliance: SPC-5 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5002538b101e36f0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:48 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current temperature = 20 Lifetime maximum temperature = 41 Lifetime minimum temperature = 15 Maximum temperature since power on = 27 Minimum temperature since power on = 18 Manufactured in week 05 of year 2020 Accumulated start-stop cycles: 17 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 119855.802 0 write: 0 0 0 0 0 97837.181 0 verify: 0 0 0 0 0 3.069 0 Non-medium error count: 69 Pending defect count:0 Pending Defects SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 96 2 - [- - -] # 2 Background short Completed 96 1 - [- - -] Long (extended) Self-test duration: 3600 seconds [60.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 26185:01 [1571101 minutes] Number of background scans performed: 38, scan progress: 83.04% Number of background medium scans performed: 38 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5002538b101e36f2 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 1 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 3976364 Received SSP frame error count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5002538b101e36f3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 /dev/da10 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL7 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ce94d2f7 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:48 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 25 C Drive Trip Temperature: 60 C Manufactured in week 06 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 167 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 22457 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1574181800 Blocks received from initiator = 3635282624 Blocks read from cache and sent to initiator = 392556365 Number of read and write commands whose size <= segment size = 80076854 Number of read and write commands whose size > segment size = 1653421 Vendor (Seagate/Hitachi) factory information number of hours powered up = 26187.60 number of minutes until next internal SMART test = 11 Seagate FARM log supported [try: -l farm] Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 105741.050 0 write: 0 0 1 1 1 51043.425 0 verify: 0 0 0 0 0 46.525 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [12.6 hours] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 26187:36 [1571256 minutes] Number of background scans performed: 182, scan progress: 0.00% Number of background medium scans performed: 182 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c500ce94d2f5 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 16 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ce94d2f6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/da11 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL7 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ce860923 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:49 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 25 C Drive Trip Temperature: 60 C Manufactured in week 06 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 171 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 22462 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1566048488 Blocks received from initiator = 3649055864 Blocks read from cache and sent to initiator = 431753326 Number of read and write commands whose size <= segment size = 80696667 Number of read and write commands whose size > segment size = 1683422 Vendor (Seagate/Hitachi) factory information number of hours powered up = 26186.82 number of minutes until next internal SMART test = 13 Seagate FARM log supported [try: -l farm] Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 105736.140 0 write: 0 0 0 0 0 51051.492 0 verify: 0 0 0 0 0 47.206 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [12.6 hours] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 26186:49 [1571209 minutes] Number of background scans performed: 182, scan progress: 0.00% Number of background medium scans performed: 182 # when lba(hex) [sk,asc,ascq] reassign_status 1 15280:15 0000000151703b78 [1,18,4] Recovered via rewrite in-place Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c500ce860921 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 17 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ce860922 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/da2 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SAMSUNG Product: MZILT3T8HALS0D3 Revision: DSF8 Compliance: SPC-5 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5002538b101e37c0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:50 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current temperature = 21 Lifetime maximum temperature = 39 Lifetime minimum temperature = 15 Maximum temperature since power on = 28 Minimum temperature since power on = 19 Manufactured in week 05 of year 2020 Accumulated start-stop cycles: 17 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 120854.176 0 write: 0 0 0 0 0 97783.825 0 verify: 0 0 0 0 0 3.103 0 Non-medium error count: 69 Pending defect count:0 Pending Defects SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 96 2 - [- - -] # 2 Background short Completed 96 1 - [- - -] Long (extended) Self-test duration: 3600 seconds [60.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 26184:41 [1571081 minutes] Number of background scans performed: 38, scan progress: 82.82% Number of background medium scans performed: 38 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5002538b101e37c2 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 2 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 3969368 Received SSP frame error count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5002538b101e37c3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 /dev/da3 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SAMSUNG Product: MZILT3T8HALS0D3 Revision: DSF8 Compliance: SPC-5 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5002538b101e3750 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:50 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current temperature = 19 Lifetime maximum temperature = 38 Lifetime minimum temperature = 14 Maximum temperature since power on = 27 Minimum temperature since power on = 17 Manufactured in week 05 of year 2020 Accumulated start-stop cycles: 17 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 120911.131 0 write: 0 0 0 0 0 97806.795 0 verify: 0 0 0 0 0 3.103 0 Non-medium error count: 69 Pending defect count:0 Pending Defects SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 96 2 - [- - -] # 2 Background short Completed 96 1 - [- - -] Long (extended) Self-test duration: 3600 seconds [60.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 26185:00 [1571100 minutes] Number of background scans performed: 38, scan progress: 83.18% Number of background medium scans performed: 38 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5002538b101e3752 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 3 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 4015616 Received SSP frame error count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5002538b101e3753 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 /dev/da4 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SAMSUNG Product: MZILT3T8HBLS0D3 Revision: DSA3 Compliance: SPC-5 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5002538b11137f60 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:50 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 0% Current temperature = 20 Lifetime maximum temperature = 45 Lifetime minimum temperature = 18 Maximum temperature since power on = 27 Minimum temperature since power on = 18 Manufactured in week 02 of year 2021 Accumulated start-stop cycles: 19 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 75368.072 0 write: 0 0 0 0 0 71818.162 0 verify: 0 0 0 0 0 0.002 0 Non-medium error count: 9063 Pending defect count:0 Pending Defects SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 96 3 - [- - -] # 2 Background short Completed 96 3 - [- - -] Long (extended) Self-test duration: 3600 seconds [60.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 16296:14 [977774 minutes] Number of background scans performed: 23, scan progress: 34.87% Number of background medium scans performed: 23 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: loss of dword synchronization reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5002538b11137f62 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 4 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 3564599 Received SSP frame error count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5002538b11137f63 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 /dev/da5 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SAMSUNG Product: MZILT3T8HALS0D3 Revision: DSF8 Compliance: SPC-5 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5002538b101e3690 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:50 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 1% Current temperature = 21 Lifetime maximum temperature = 42 Lifetime minimum temperature = 16 Maximum temperature since power on = 27 Minimum temperature since power on = 19 Manufactured in week 05 of year 2020 Accumulated start-stop cycles: 17 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 120614.693 0 write: 0 0 0 0 0 97783.825 0 verify: 0 0 0 0 0 3.103 0 Non-medium error count: 69 Pending defect count:0 Pending Defects SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed 96 2 - [- - -] # 2 Background short Completed 96 1 - [- - -] Long (extended) Self-test duration: 3600 seconds [60.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 26185:00 [1571100 minutes] Number of background scans performed: 38, scan progress: 82.98% Number of background medium scans performed: 38 Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5002538b101e3692 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 5 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 4116567 Received SSP frame error count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5002538b101e3693 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 /dev/da6 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Dell Certified Intel S4x00/D3-S4x10 Series SSDs Device Model: SSDSC2KG480G8R Serial Number: -- LU WWN Device Id: 5 5cd2e4 ... Add. Product Id: DELL(tm) Firmware Version: XCV1DL67 User Capacity: 480,103,981,056 bytes [480 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Mar 25 08:42:50 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 72) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 60) minutes. Conveyance self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -OSR-- 130 130 039 - 1371466214 5 Reallocated_Sector_Ct PO--CK 100 100 001 - 0 9 Power_On_Hours -O--CK 100 100 000 - 25951 12 Power_Cycle_Count -O--CK 100 100 000 - 17 13 Read_Soft_Error_Rate -OSRC- 080 080 000 - 281472053209574 170 Available_Reservd_Space PO--CK 100 100 010 - 0 173 Unknown_Attribute -O--C- 100 100 000 - 19 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 16 175 Program_Fail_Count_Chip -O--C- 100 100 010 - 18 179 Used_Rsvd_Blk_Cnt_Tot PO--CK 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot -O--CK 100 100 000 - 6129 181 Program_Fail_Cnt_Total -O-RCK 100 100 000 - 0 182 Erase_Fail_Count_Total -O-RCK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 000 - 19 195 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 201 Power_Loss_Cap_Test PO--CK 100 100 010 - 2459 (21 65535) 202 End_of_Life POS--K 100 100 000 - 0 233 Total_LBAs_Written -O--CK 100 100 000 - 145960 234 Thermal_Throttle_Status -O--CK 100 100 000 - 0/0 235 Unknown_Attribute PO-R-- 100 100 000 - 145960 241 Total_LBAs_Written -O--CK 100 100 000 - 145960 242 Total_LBAs_Read -O--CK 100 100 000 - 35591 245 Percent_Life_Remaining -O--CK 100 100 000 - 100 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x25 GPL R/O 512 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x99-0x9a GPL,SL R/W 1 Host vendor specific log 0xb8 SL VS 1 Device vendor specific log 0xb9 SL VS 8 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xc8 GPL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 1 - # 2 Short offline Completed without error 00% 1 - Read SMART Selective Self-test Log failed: SAT command failed SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 17/25 Celsius Lifetime Min/Max Temperature: 10/31 Celsius Specified Max Operating Temperature: 73 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/73 Celsius Min/Max Temperature Limit: 0/73 Celsius Temperature History Size (Index): 478 (251) Index Estimated Time Temperature Celsius 252 2024-03-25 00:45 20 * ... ..( 17 skipped). .. * 270 2024-03-25 01:03 20 * 271 2024-03-25 01:04 21 ** ... ..( 10 skipped). .. ** 282 2024-03-25 01:15 21 ** 283 2024-03-25 01:16 20 * 284 2024-03-25 01:17 20 * 285 2024-03-25 01:18 21 ** 286 2024-03-25 01:19 20 * ... ..( 6 skipped). .. * 293 2024-03-25 01:26 20 * 294 2024-03-25 01:27 21 ** 295 2024-03-25 01:28 21 ** 296 2024-03-25 01:29 20 * ... ..(102 skipped). .. * 399 2024-03-25 03:12 20 * 400 2024-03-25 03:13 21 ** ... ..( 9 skipped). .. ** 410 2024-03-25 03:23 21 ** 411 2024-03-25 03:24 20 * ... ..(128 skipped). .. * 62 2024-03-25 05:33 20 * 63 2024-03-25 05:34 19 - ... ..( 18 skipped). .. - 82 2024-03-25 05:53 19 - 83 2024-03-25 05:54 20 * ... ..( 5 skipped). .. * 89 2024-03-25 06:00 20 * 90 2024-03-25 06:01 19 - ... ..( 2 skipped). .. - 93 2024-03-25 06:04 19 - 94 2024-03-25 06:05 20 * ... ..( 31 skipped). .. * 126 2024-03-25 06:37 20 * 127 2024-03-25 06:38 19 - ... ..( 15 skipped). .. - 143 2024-03-25 06:54 19 - 144 2024-03-25 06:55 20 * ... ..( 69 skipped). .. * 214 2024-03-25 08:05 20 * 215 2024-03-25 08:06 21 ** 216 2024-03-25 08:07 20 * ... ..( 30 skipped). .. * 247 2024-03-25 08:38 20 * 248 2024-03-25 08:39 19 - ... ..( 2 skipped). .. - 251 2024-03-25 08:42 19 - SCT Error Recovery Control: Read: 80 (8.0 seconds) Write: 80 (8.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 17 --- Lifetime Power-On Resets 0x01 0x018 6 9565648025 --- Logical Sectors Written 0x01 0x020 6 321860447 --- Number of Write Commands 0x01 0x028 6 2332552324 --- Logical Sectors Read 0x01 0x030 6 45996828 --- Number of Read Commands 0x01 0x038 6 3232241452 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 19 --- Current Temperature 0x05 0x010 1 19 --- Average Short Term Temperature 0x05 0x018 1 19 --- Average Long Term Temperature 0x05 0x020 1 31 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 21 --- Highest Average Short Term Temperature 0x05 0x038 1 18 --- Lowest Average Short Term Temperature 0x05 0x040 1 20 --- Highest Average Long Term Temperature 0x05 0x048 1 18 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 73 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 0 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x000a 4 1 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/da7 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Dell Certified Intel S4x00/D3-S4x10 Series SSDs Device Model: SSDSC2KG480G8R Serial Number: -- LU WWN Device Id: 5 5cd2e4 ... Add. Product Id: DELL(tm) Firmware Version: XCV1DL67 User Capacity: 480,103,981,056 bytes [480 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Mar 25 08:42:51 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 72) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 60) minutes. Conveyance self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -OSR-- 130 130 039 - 1357851258 5 Reallocated_Sector_Ct PO--CK 100 100 001 - 0 9 Power_On_Hours -O--CK 100 100 000 - 25952 12 Power_Cycle_Count -O--CK 100 100 000 - 17 13 Read_Soft_Error_Rate -OSRC- 083 080 000 - 281472039594618 170 Available_Reservd_Space PO--CK 100 100 010 - 0 173 Unknown_Attribute -O--C- 100 100 000 - 19 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 16 175 Program_Fail_Count_Chip -O--C- 100 100 010 - 18 179 Used_Rsvd_Blk_Cnt_Tot PO--CK 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot -O--CK 100 100 000 - 6131 181 Program_Fail_Cnt_Total -O-RCK 100 100 000 - 0 182 Erase_Fail_Count_Total -O-RCK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 000 - 19 195 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 201 Power_Loss_Cap_Test PO--CK 100 100 010 - 2526 (21 65535) 202 End_of_Life POS--K 100 100 000 - 0 233 Total_LBAs_Written -O--CK 100 100 000 - 145919 234 Thermal_Throttle_Status -O--CK 100 100 000 - 0/0 235 Unknown_Attribute PO-R-- 100 100 000 - 145919 241 Total_LBAs_Written -O--CK 100 100 000 - 145919 242 Total_LBAs_Read -O--CK 100 100 000 - 35304 245 Percent_Life_Remaining -O--CK 100 100 000 - 100 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x25 GPL R/O 512 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x99-0x9a GPL,SL R/W 1 Host vendor specific log 0xb8 SL VS 1 Device vendor specific log 0xb9 SL VS 8 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xc8 GPL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 1 - # 2 Short offline Completed without error 00% 1 - Read SMART Selective Self-test Log failed: SAT command failed SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 15/24 Celsius Lifetime Min/Max Temperature: 10/30 Celsius Specified Max Operating Temperature: 73 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/73 Celsius Min/Max Temperature Limit: 0/73 Celsius Temperature History Size (Index): 478 (256) Index Estimated Time Temperature Celsius 257 2024-03-25 00:45 19 - ... ..( 44 skipped). .. - 302 2024-03-25 01:30 19 - 303 2024-03-25 01:31 20 * 304 2024-03-25 01:32 18 - 305 2024-03-25 01:33 19 - ... ..( 11 skipped). .. - 317 2024-03-25 01:45 19 - 318 2024-03-25 01:46 20 * 319 2024-03-25 01:47 19 - ... ..( 8 skipped). .. - 328 2024-03-25 01:56 19 - 329 2024-03-25 01:57 18 - 330 2024-03-25 01:58 19 - ... ..( 28 skipped). .. - 359 2024-03-25 02:27 19 - 360 2024-03-25 02:28 18 - 361 2024-03-25 02:29 19 - ... ..( 43 skipped). .. - 405 2024-03-25 03:13 19 - 406 2024-03-25 03:14 18 - 407 2024-03-25 03:15 19 - ... ..( 20 skipped). .. - 428 2024-03-25 03:36 19 - 429 2024-03-25 03:37 18 - 430 2024-03-25 03:38 19 - ... ..( 3 skipped). .. - 434 2024-03-25 03:42 19 - 435 2024-03-25 03:43 20 * 436 2024-03-25 03:44 19 - ... ..( 57 skipped). .. - 16 2024-03-25 04:42 19 - 17 2024-03-25 04:43 18 - 18 2024-03-25 04:44 19 - 19 2024-03-25 04:45 19 - 20 2024-03-25 04:46 18 - 21 2024-03-25 04:47 19 - ... ..( 13 skipped). .. - 35 2024-03-25 05:01 19 - 36 2024-03-25 05:02 18 - 37 2024-03-25 05:03 19 - 38 2024-03-25 05:04 18 - 39 2024-03-25 05:05 19 - 40 2024-03-25 05:06 18 - 41 2024-03-25 05:07 19 - 42 2024-03-25 05:08 18 - 43 2024-03-25 05:09 19 - 44 2024-03-25 05:10 19 - 45 2024-03-25 05:11 18 - 46 2024-03-25 05:12 19 - ... ..( 5 skipped). .. - 52 2024-03-25 05:18 19 - 53 2024-03-25 05:19 18 - ... ..( 3 skipped). .. - 57 2024-03-25 05:23 18 - 58 2024-03-25 05:24 19 - 59 2024-03-25 05:25 18 - 60 2024-03-25 05:26 18 - 61 2024-03-25 05:27 19 - 62 2024-03-25 05:28 18 - 63 2024-03-25 05:29 19 - 64 2024-03-25 05:30 18 - 65 2024-03-25 05:31 19 - 66 2024-03-25 05:32 18 - ... ..( 3 skipped). .. - 70 2024-03-25 05:36 18 - 71 2024-03-25 05:37 19 - 72 2024-03-25 05:38 18 - 73 2024-03-25 05:39 18 - 74 2024-03-25 05:40 18 - 75 2024-03-25 05:41 19 - 76 2024-03-25 05:42 18 - 77 2024-03-25 05:43 18 - 78 2024-03-25 05:44 18 - 79 2024-03-25 05:45 19 - 80 2024-03-25 05:46 18 - 81 2024-03-25 05:47 18 - 82 2024-03-25 05:48 18 - 83 2024-03-25 05:49 19 - 84 2024-03-25 05:50 18 - ... ..( 20 skipped). .. - 105 2024-03-25 06:11 18 - 106 2024-03-25 06:12 19 - 107 2024-03-25 06:13 18 - 108 2024-03-25 06:14 19 - 109 2024-03-25 06:15 19 - 110 2024-03-25 06:16 19 - 111 2024-03-25 06:17 18 - ... ..( 2 skipped). .. - 114 2024-03-25 06:20 18 - 115 2024-03-25 06:21 19 - 116 2024-03-25 06:22 19 - 117 2024-03-25 06:23 18 - ... ..( 22 skipped). .. - 140 2024-03-25 06:46 18 - 141 2024-03-25 06:47 19 - 142 2024-03-25 06:48 18 - ... ..( 6 skipped). .. - 149 2024-03-25 06:55 18 - 150 2024-03-25 06:56 19 - 151 2024-03-25 06:57 19 - 152 2024-03-25 06:58 18 - 153 2024-03-25 06:59 19 - ... ..( 4 skipped). .. - 158 2024-03-25 07:04 19 - 159 2024-03-25 07:05 18 - 160 2024-03-25 07:06 19 - 161 2024-03-25 07:07 19 - 162 2024-03-25 07:08 18 - 163 2024-03-25 07:09 19 - 164 2024-03-25 07:10 19 - 165 2024-03-25 07:11 18 - 166 2024-03-25 07:12 19 - ... ..( 7 skipped). .. - 174 2024-03-25 07:20 19 - 175 2024-03-25 07:21 18 - 176 2024-03-25 07:22 19 - ... ..( 19 skipped). .. - 196 2024-03-25 07:42 19 - 197 2024-03-25 07:43 18 - 198 2024-03-25 07:44 19 - 199 2024-03-25 07:45 18 - 200 2024-03-25 07:46 18 - 201 2024-03-25 07:47 19 - ... ..( 17 skipped). .. - 219 2024-03-25 08:05 19 - 220 2024-03-25 08:06 18 - 221 2024-03-25 08:07 19 - 222 2024-03-25 08:08 19 - 223 2024-03-25 08:09 19 - 224 2024-03-25 08:10 18 - 225 2024-03-25 08:11 19 - 226 2024-03-25 08:12 19 - 227 2024-03-25 08:13 19 - 228 2024-03-25 08:14 18 - 229 2024-03-25 08:15 19 - 230 2024-03-25 08:16 18 - 231 2024-03-25 08:17 18 - 232 2024-03-25 08:18 19 - 233 2024-03-25 08:19 18 - ... ..( 2 skipped). .. - 236 2024-03-25 08:22 18 - 237 2024-03-25 08:23 19 - 238 2024-03-25 08:24 19 - 239 2024-03-25 08:25 18 - ... ..( 2 skipped). .. - 242 2024-03-25 08:28 18 - 243 2024-03-25 08:29 19 - 244 2024-03-25 08:30 18 - 245 2024-03-25 08:31 19 - 246 2024-03-25 08:32 18 - ... ..( 2 skipped). .. - 249 2024-03-25 08:35 18 - 250 2024-03-25 08:36 19 - 251 2024-03-25 08:37 18 - 252 2024-03-25 08:38 18 - 253 2024-03-25 08:39 19 - 254 2024-03-25 08:40 18 - 255 2024-03-25 08:41 18 - 256 2024-03-25 08:42 18 - SCT Error Recovery Control: Read: 80 (8.0 seconds) Write: 80 (8.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 17 --- Lifetime Power-On Resets 0x01 0x018 6 9562994836 --- Logical Sectors Written 0x01 0x020 6 320716067 --- Number of Write Commands 0x01 0x028 6 2313706216 --- Logical Sectors Read 0x01 0x030 6 43943098 --- Number of Read Commands 0x01 0x038 6 3233085166 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 19 --- Current Temperature 0x05 0x010 1 18 --- Average Short Term Temperature 0x05 0x018 1 18 --- Average Long Term Temperature 0x05 0x020 1 29 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 20 --- Highest Average Short Term Temperature 0x05 0x038 1 16 --- Lowest Average Short Term Temperature 0x05 0x040 1 18 --- Highest Average Long Term Temperature 0x05 0x048 1 16 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 73 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 0 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x000a 4 1 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/da8 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL7 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ce78e70b Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:51 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 25 C Drive Trip Temperature: 60 C Manufactured in week 06 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 171 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 22542 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1602391576 Blocks received from initiator = 3744774992 Blocks read from cache and sent to initiator = 434214555 Number of read and write commands whose size <= segment size = 80495458 Number of read and write commands whose size > segment size = 1680539 Vendor (Seagate/Hitachi) factory information number of hours powered up = 26186.85 number of minutes until next internal SMART test = 10 Seagate FARM log supported [try: -l farm] Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 8 0 8 8 105756.910 0 write: 0 0 1 1 1 51102.036 0 verify: 0 0 0 0 0 45.334 0 Non-medium error count: 2 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [12.6 hours] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 26186:51 [1571211 minutes] Number of background scans performed: 182, scan progress: 0.00% Number of background medium scans performed: 182 # when lba(hex) [sk,asc,ascq] reassign_status 1 9172:53 0000000255a72298 [1,18,4] Recovered via rewrite in-place Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c500ce78e709 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 14 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ce78e70a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/da9 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST8000NM014A Revision: CSL7 Compliance: SPC-5 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500ce87310b Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Mar 25 08:42:52 2024 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 25 C Drive Trip Temperature: 60 C Manufactured in week 06 of year 2020 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 172 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 22591 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1690066632 Blocks received from initiator = 3733710400 Blocks read from cache and sent to initiator = 437444999 Number of read and write commands whose size <= segment size = 80295031 Number of read and write commands whose size > segment size = 1682245 Vendor (Seagate/Hitachi) factory information number of hours powered up = 26187.12 number of minutes until next internal SMART test = 2 Seagate FARM log supported [try: -l farm] Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 2 0 2 2 105799.008 0 write: 0 0 2 2 2 51096.165 0 verify: 0 0 0 0 0 48.827 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 80 3 - [- - -] # 2 Background short Completed - 1 - [- - -] Long (extended) Self-test duration: 45480 seconds [12.6 hours] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 26187:07 [1571227 minutes] Number of background scans performed: 182, scan progress: 0.00% Number of background medium scans performed: 182 # when lba(hex) [sk,asc,ascq] reassign_status 1 8807:37 0000000230315858 [1,18,4] Recovered via rewrite in-place Device does not support General statistics and performance logging Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c500ce873109 attached SAS address = 0x500056b343b1f2ff attached phy identifier = 15 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500ce87310a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0