/dev/sd0 smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.7 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Silicon Motion based SSDs Device Model: ADATA SU630 Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: XD0R6308 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Sep 23 16:37:21 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1) seconds. Offline data collection capabilities: (0x59) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 100 050 Pre-fail Always - 0 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 6529 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 136 160 Uncorrectable_Error_Cnt 0x0032 100 100 050 Old_age Always - 0 161 Valid_Spare_Block_Cnt 0x0032 100 100 050 Old_age Always - 100 163 Initial_Bad_Block_Count 0x0032 100 100 000 Old_age Always - 25 164 Total_Erase_Count 0x0032 100 100 000 Old_age Always - 19511 165 Max_Erase_Count 0x0032 100 100 000 Old_age Always - 82 166 Min_Erase_Count 0x0032 100 100 000 Old_age Always - 6 167 Average_Erase_Count 0x0032 100 100 000 Old_age Always - 36 148 Total_SLC_Erase_Ct 0x0032 100 100 000 Old_age Always - 58533 149 Max_SLC_Erase_Ct 0x0032 100 100 000 Old_age Always - 248 150 Min_SLC_Erase_Ct 0x0032 100 100 000 Old_age Always - 20 151 Average_SLC_Erase_Ct 0x0032 100 100 000 Old_age Always - 109 159 DRAM_1_Bit_Error_Count 0x0032 100 100 000 Old_age Always - 0 168 Max_Erase_Count_of_Spec 0x0032 100 100 000 Old_age Always - 248 169 Remaining_Lifetime_Perc 0x0032 100 100 000 Old_age Always - 99 177 Wear_Leveling_Count 0x0032 100 100 000 Old_age Always - 200 181 Program_Fail_Cnt_Total 0x0032 100 100 000 Old_age Always - 0 182 Erase_Fail_Count_Total 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 71 194 Temperature_Celsius 0x0032 100 100 000 Old_age Always - 29 195 Hardware_ECC_Recovered 0x0032 100 100 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0 232 Available_Reservd_Space 0x0032 100 100 000 Old_age Always - 100 241 Host_Writes_32MiB 0x0032 100 100 000 Old_age Always - 194197 242 Host_Reads_32MiB 0x0032 100 100 000 Old_age Always - 215887 245 TLC_Writes_32MiB 0x0032 100 100 000 Old_age Always - 267009 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. The above only provides legacy SMART information - try 'smartctl -x' for more