/dev/sd0 smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.6 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: PNY CS900 1TB SSD Serial Number: -- LU WWN Device Id: 5 f8db4c ... Firmware Version: CS9006B5 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Mar 18 09:00:31 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 2076 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 263 168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0 170 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 290 173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 131090 192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 156 194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33) 218 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0 231 Unknown_SSD_Attribute 0x0013 100 100 000 Pre-fail Always - 99 241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 1716 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. The above only provides legacy SMART information - try 'smartctl -x' for more /dev/sd1 smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.6 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Geonix Gold 256GB Serial Number: -- Firmware Version: 666 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Mar 18 09:00:31 2025 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0032 100 100 050 Old_age Always - 0 5 Reallocated_Sector_Ct 0x0032 100 100 050 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 050 Old_age Always - 753 12 Power_Cycle_Count 0x0032 100 100 050 Old_age Always - 444 160 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 0 161 Unknown_Attribute 0x0033 100 100 050 Pre-fail Always - 100 163 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 15 164 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 33324 165 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 27 166 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 4 167 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 11 168 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 5050 169 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 100 175 Program_Fail_Count_Chip 0x0032 100 100 050 Old_age Always - 0 176 Erase_Fail_Count_Chip 0x0032 100 100 050 Old_age Always - 0 177 Wear_Leveling_Count 0x0032 100 100 050 Old_age Always - 0 178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 050 Old_age Always - 0 181 Program_Fail_Cnt_Total 0x0032 100 100 050 Old_age Always - 0 182 Erase_Fail_Count_Total 0x0032 100 100 050 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always - 366 194 Temperature_Celsius 0x0022 100 100 050 Old_age Always - 40 195 Hardware_ECC_Recovered 0x0032 100 100 050 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 100 100 050 Old_age Always - 0 197 Current_Pending_Sector 0x0032 100 100 050 Old_age Always - 0 198 Offline_Uncorrectable 0x0032 100 100 050 Old_age Always - 0 199 UDMA_CRC_Error_Count 0x0032 100 100 050 Old_age Always - 4 232 Available_Reservd_Space 0x0032 100 100 050 Old_age Always - 100 241 Total_LBAs_Written 0x0030 100 100 050 Old_age Offline - 26282 242 Total_LBAs_Read 0x0030 100 100 050 Old_age Offline - 7649 245 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 14766 SMART Error Log Version: 1 ATA Error Count: 4 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 0 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d0 01 00 4f c2 00 00 00:00:00.000 SMART READ DATA b0 d1 01 01 4f c2 00 00 00:00:00.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] b0 da 00 00 4f c2 00 00 00:00:00.000 SMART RETURN STATUS b0 d5 01 00 4f c2 00 00 00:00:00.000 SMART READ LOG b0 d5 01 01 4f c2 00 00 00:00:00.000 SMART READ LOG SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported The above only provides legacy SMART information - try 'smartctl -x' for more /dev/sd2 smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.6 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: OPENBSD Product: SR CRYPTO Revision: 006 User Capacity: 256,060,211,200 bytes [256 GB] Logical block size: 512 bytes >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.