/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-CURRENT amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SSD 120GB Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: 1.00 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 17 11:18:22 2021 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 099 099 050 - 23 5 Reallocated_Sector_Ct ------ 100 100 000 - 2 9 Power_On_Hours -O--CK 100 100 000 - 5006 12 Power_Cycle_Count ------ 100 100 000 - 1036 160 Unknown_Attribute ------ 100 100 000 - 1 161 Unknown_Attribute ------ 100 100 000 - 0 163 Unknown_Attribute ------ 100 100 000 - 0 165 Unknown_Attribute ------ 100 100 000 - 138 166 Unknown_Attribute ------ 100 100 000 - 80 167 Unknown_Attribute ------ 100 100 000 - 133 192 Power-Off_Retract_Count ------ 100 100 000 - 77 194 Temperature_Celsius ------ 100 100 000 - 40 195 Hardware_ECC_Recovered ------ 100 100 000 - 6600 196 Reallocated_Event_Count ------ 100 100 000 - 0 199 UDMA_CRC_Error_Count ------ 100 100 000 - 0 241 Total_LBAs_Written ------ 100 100 000 - 316561 242 Total_LBAs_Read ------ 100 100 000 - 360574 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 10 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [9] occurred at disk power-on lifetime: 3 hours (0 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT Error 9 [8] occurred at disk power-on lifetime: 12 hours (0 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT Error 8 [7] occurred at disk power-on lifetime: 12 hours (0 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT Error 7 [6] occurred at disk power-on lifetime: 12 hours (0 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT Error 6 [5] occurred at disk power-on lifetime: 4 hours (0 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT Error 5 [4] occurred at disk power-on lifetime: 4 hours (0 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT Error 4 [3] occurred at disk power-on lifetime: 4 hours (0 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT Error 3 [2] occurred at disk power-on lifetime: 3 hours (0 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 60 00 08 00 78 00 00 03 89 01 f0 40 08 00:00:00.000 READ FPDMA QUEUED 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:00:00.000 DATA SET MANAGEMENT 61 00 10 00 a0 00 00 03 8b 64 08 40 08 00:00:00.000 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4919 - # 2 Short offline Completed without error 00% 4906 - # 3 Short offline Completed without error 00% 2967 - # 4 Short offline Completed without error 00% 2548 - # 5 Short offline Completed without error 00% 2534 - # 6 Short offline Completed without error 00% 2520 - # 7 Short offline Completed without error 00% 1428 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1036 --- Lifetime Power-On Resets 0x01 0x010 4 5006 --- Power-on Hours 0x01 0x018 6 20746196526 --- Logical Sectors Written 0x01 0x028 6 23630632388 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 23 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 40 --- Current Temperature 0x05 0x020 1 40 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 16745 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 4 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 11 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/ada1 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-CURRENT amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-75WN4A1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 13057113 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 17 11:18:22 2021 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 115) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 173 173 021 - 2308 4 Start_Stop_Count -O--CK 100 100 000 - 336 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 098 098 000 - 1797 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 336 192 Power-Off_Retract_Count -O--CK 200 200 000 - 8 193 Load_Cycle_Count -O--CK 185 185 000 - 45062 194 Temperature_Celsius -O---K 104 097 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 240 Head_Flying_Hours -O--CK 098 098 000 - 1552 241 Total_LBAs_Written -O--CK 200 200 000 - 14059109351 242 Total_LBAs_Read -O--CK 200 200 000 - 10329679496 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 48 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1710 - # 2 Short offline Completed without error 00% 1697 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 27/41 Celsius Lifetime Min/Max Temperature: 23/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (421) Index Estimated Time Temperature Celsius 422 2021-02-17 03:21 39 ******************** ... ..( 48 skipped). .. ******************** 471 2021-02-17 04:10 39 ******************** 472 2021-02-17 04:11 40 ********************* ... ..( 20 skipped). .. ********************* 15 2021-02-17 04:32 40 ********************* 16 2021-02-17 04:33 41 ********************** ... ..( 47 skipped). .. ********************** 64 2021-02-17 05:21 41 ********************** 65 2021-02-17 05:22 40 ********************* ... ..( 9 skipped). .. ********************* 75 2021-02-17 05:32 40 ********************* 76 2021-02-17 05:33 39 ******************** ... ..( 11 skipped). .. ******************** 88 2021-02-17 05:45 39 ******************** 89 2021-02-17 05:46 ? - 90 2021-02-17 05:47 33 ************** 91 2021-02-17 05:48 33 ************** 92 2021-02-17 05:49 33 ************** 93 2021-02-17 05:50 34 *************** 94 2021-02-17 05:51 34 *************** 95 2021-02-17 05:52 35 **************** 96 2021-02-17 05:53 35 **************** 97 2021-02-17 05:54 35 **************** 98 2021-02-17 05:55 36 ***************** ... ..( 2 skipped). .. ***************** 101 2021-02-17 05:58 36 ***************** 102 2021-02-17 05:59 37 ****************** 103 2021-02-17 06:00 37 ****************** 104 2021-02-17 06:01 37 ****************** 105 2021-02-17 06:02 38 ******************* ... ..( 13 skipped). .. ******************* 119 2021-02-17 06:16 38 ******************* 120 2021-02-17 06:17 39 ******************** ... ..( 9 skipped). .. ******************** 130 2021-02-17 06:27 39 ******************** 131 2021-02-17 06:28 40 ********************* ... ..( 32 skipped). .. ********************* 164 2021-02-17 07:01 40 ********************* 165 2021-02-17 07:02 41 ********************** ... ..( 13 skipped). .. ********************** 179 2021-02-17 07:16 41 ********************** 180 2021-02-17 07:17 40 ********************* ... ..( 56 skipped). .. ********************* 237 2021-02-17 08:14 40 ********************* 238 2021-02-17 08:15 ? - 239 2021-02-17 08:16 27 ******** 240 2021-02-17 08:17 27 ******** 241 2021-02-17 08:18 27 ******** 242 2021-02-17 08:19 28 ********* 243 2021-02-17 08:20 28 ********* 244 2021-02-17 08:21 29 ********** 245 2021-02-17 08:22 30 *********** 246 2021-02-17 08:23 30 *********** 247 2021-02-17 08:24 31 ************ 248 2021-02-17 08:25 31 ************ 249 2021-02-17 08:26 32 ************* 250 2021-02-17 08:27 32 ************* 251 2021-02-17 08:28 32 ************* 252 2021-02-17 08:29 33 ************** 253 2021-02-17 08:30 34 *************** 254 2021-02-17 08:31 34 *************** 255 2021-02-17 08:32 35 **************** ... ..( 3 skipped). .. **************** 259 2021-02-17 08:36 35 **************** 260 2021-02-17 08:37 36 ***************** ... ..( 4 skipped). .. ***************** 265 2021-02-17 08:42 36 ***************** 266 2021-02-17 08:43 37 ****************** ... ..( 4 skipped). .. ****************** 271 2021-02-17 08:48 37 ****************** 272 2021-02-17 08:49 38 ******************* ... ..( 26 skipped). .. ******************* 299 2021-02-17 09:16 38 ******************* 300 2021-02-17 09:17 39 ******************** ... ..( 29 skipped). .. ******************** 330 2021-02-17 09:47 39 ******************** 331 2021-02-17 09:48 40 ********************* ... ..( 56 skipped). .. ********************* 388 2021-02-17 10:45 40 ********************* 389 2021-02-17 10:46 41 ********************** 390 2021-02-17 10:47 41 ********************** 391 2021-02-17 10:48 40 ********************* ... ..( 15 skipped). .. ********************* 407 2021-02-17 11:04 40 ********************* 408 2021-02-17 11:05 41 ********************** ... ..( 2 skipped). .. ********************** 411 2021-02-17 11:08 41 ********************** 412 2021-02-17 11:09 40 ********************* ... ..( 7 skipped). .. ********************* 420 2021-02-17 11:17 40 ********************* 421 2021-02-17 11:18 39 ******************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 14077 Vendor specific