/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Mobile (SMR) Device Model: WDC WD10SPZX-75Z10T2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 03.01A03 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Jun 27 10:05:14 2024 IST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3720) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 251) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 195 188 021 - 1250 4 Start_Stop_Count -O--CK 088 088 000 - 12549 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 081 081 000 - 14387 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4632 191 G-Sense_Error_Rate -O--CK 001 001 000 - 8858 192 Power-Off_Retract_Count -O--CK 200 200 000 - 654 193 Load_Cycle_Count -O--CK 173 173 000 - 82563 194 Temperature_Celsius -O---K 112 094 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 2 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 240 Head_Flying_Hours -O--CK 087 087 000 - 9550 241 Total_LBAs_Written -O--CK 200 200 000 - 61069346886 242 Total_LBAs_Read -O--CK 200 200 000 - 79766661300 254 Free_Fall_Sensor -O--CK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 74 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 14215 - # 2 Short offline Completed without error 00% 13733 - # 3 Short offline Interrupted (host reset) 80% 10636 - # 4 Short offline Interrupted (host reset) 90% 10636 - # 5 Short offline Interrupted (host reset) 90% 10635 - # 6 Short offline Interrupted (host reset) 90% 10635 - # 7 Short offline Interrupted (host reset) 90% 10632 - # 8 Short offline Interrupted (host reset) 90% 10498 - # 9 Short offline Aborted by host 90% 10421 - #10 Short offline Aborted by host 90% 10258 - #11 Short offline Aborted by host 90% 10258 - #12 Short offline Aborted by host 90% 10258 - #13 Short offline Interrupted (host reset) 90% 10215 - #14 Short offline Aborted by host 90% 10214 - #15 Short offline Aborted by host 90% 10076 - #16 Short offline Interrupted (host reset) 90% 9874 - #17 Short offline Aborted by host 90% 9567 - #18 Short offline Aborted by host 90% 9183 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 30/32 Celsius Lifetime Min/Max Temperature: 20/49 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (71) Index Estimated Time Temperature Celsius 72 2024-06-27 07:58 30 *********** ... ..( 52 skipped). .. *********** 125 2024-06-27 08:51 30 *********** 126 2024-06-27 08:52 ? - 127 2024-06-27 08:53 30 *********** 0 2024-06-27 08:54 ? - 1 2024-06-27 08:55 30 *********** 2 2024-06-27 08:56 ? - 3 2024-06-27 08:57 30 *********** 4 2024-06-27 08:58 ? - 5 2024-06-27 08:59 30 *********** 6 2024-06-27 09:00 31 ************ ... ..( 8 skipped). .. ************ 15 2024-06-27 09:09 31 ************ 16 2024-06-27 09:10 32 ************* ... ..( 8 skipped). .. ************* 25 2024-06-27 09:19 32 ************* 26 2024-06-27 09:20 31 ************ ... ..( 6 skipped). .. ************ 33 2024-06-27 09:27 31 ************ 34 2024-06-27 09:28 30 *********** ... ..( 22 skipped). .. *********** 57 2024-06-27 09:51 30 *********** 58 2024-06-27 09:52 31 ************ 59 2024-06-27 09:53 31 ************ 60 2024-06-27 09:54 31 ************ 61 2024-06-27 09:55 ? - 62 2024-06-27 09:56 31 ************ ... ..( 8 skipped). .. ************ 71 2024-06-27 10:05 31 ************ SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 14 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 4054 Vendor specific /dev/da0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST1000LM024 HN-M101MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR10001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Jun 27 10:05:14 2024 IST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: (13260) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 221) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 98 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 086 081 025 - 4458 4 Start_Stop_Count -O--CK 095 095 000 - 5572 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 3257 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 74 12 Power_Cycle_Count -O--CK 099 099 000 - 1691 191 G-Sense_Error_Rate -O---K 100 100 000 - 106 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 061 037 000 - 39 (Min/Max 21/63) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 3762 223 Load_Retry_Count -O--CK 100 100 000 - 74 225 Load_Cycle_Count -O--CK 095 095 000 - 59387 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 91 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 91 [2] occurred at disk power-on lifetime: 2252 hours (93 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 71 00 00 00 00 b8 70 40 00 Error: UNC 113 sectors at LBA = 0x0000b870 = 47216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 71 00 00 00 00 b8 70 40 00 00:00:00.143 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.140 READ DMA EXT e5 00 00 00 00 00 00 00 00 00 00 00 00 00:00:00.139 CHECK POWER MODE 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.069 READ DMA EXT 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.067 READ DMA EXT Error 90 [1] occurred at disk power-on lifetime: 2252 hours (93 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 b8 70 40 00 Error: UNC 1 sectors at LBA = 0x0000b870 = 47216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.140 READ DMA EXT e5 00 00 00 00 00 00 00 00 00 00 00 00 00:00:00.139 CHECK POWER MODE 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.069 READ DMA EXT 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.067 READ DMA EXT 25 00 00 00 70 00 00 00 00 b8 71 40 00 00:00:00.065 READ DMA EXT Error 89 [0] occurred at disk power-on lifetime: 2252 hours (93 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 b8 70 40 00 Error: UNC 1 sectors at LBA = 0x0000b870 = 47216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.069 READ DMA EXT 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.067 READ DMA EXT 25 00 00 00 70 00 00 00 00 b8 71 40 00 00:00:00.065 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.061 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.049 READ DMA EXT Error 88 [7] occurred at disk power-on lifetime: 2252 hours (93 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 6f 00 00 00 00 b8 72 40 00 Error: UNC 111 sectors at LBA = 0x0000b872 = 47218 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.067 READ DMA EXT 25 00 00 00 70 00 00 00 00 b8 71 40 00 00:00:00.065 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.061 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.049 READ DMA EXT 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.045 READ DMA EXT Error 87 [6] occurred at disk power-on lifetime: 2252 hours (93 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 00 b8 71 40 00 Error: UNC 112 sectors at LBA = 0x0000b871 = 47217 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 70 00 00 00 00 b8 71 40 00 00:00:00.065 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.061 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.049 READ DMA EXT 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.045 READ DMA EXT 25 00 00 00 70 00 00 00 00 b8 71 40 00 00:00:00.043 READ DMA EXT Error 86 [5] occurred at disk power-on lifetime: 2252 hours (93 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 b8 70 40 00 Error: UNC 1 sectors at LBA = 0x0000b870 = 47216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.061 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.049 READ DMA EXT 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.045 READ DMA EXT 25 00 00 00 70 00 00 00 00 b8 71 40 00 00:00:00.043 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.040 READ DMA EXT Error 85 [4] occurred at disk power-on lifetime: 2252 hours (93 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 b8 70 40 00 Error: UNC 1 sectors at LBA = 0x0000b870 = 47216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.049 READ DMA EXT 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.045 READ DMA EXT 25 00 00 00 70 00 00 00 00 b8 71 40 00 00:00:00.043 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.040 READ DMA EXT 25 00 00 00 71 00 00 00 00 b8 70 40 00 00:00:00.036 READ DMA EXT Error 84 [3] occurred at disk power-on lifetime: 2252 hours (93 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 6f 00 00 00 00 b8 72 40 00 Error: UNC 111 sectors at LBA = 0x0000b872 = 47218 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 6f 00 00 00 00 b8 72 40 00 00:00:00.045 READ DMA EXT 25 00 00 00 70 00 00 00 00 b8 71 40 00 00:00:00.043 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.040 READ DMA EXT 25 00 00 00 71 00 00 00 00 b8 70 40 00 00:00:00.036 READ DMA EXT 25 00 00 00 01 00 00 00 00 b8 70 40 00 00:00:00.033 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 60% 94 - # 2 Short offline Completed without error 00% 92 - # 3 Short offline Completed without error 00% 88 - # 4 Short offline Completed without error 00% 87 - # 5 Short offline Completed without error 00% 83 - # 6 Short offline Completed without error 00% 82 - # 7 Short offline Completed without error 00% 80 - # 8 Short offline Completed without error 00% 80 - # 9 Short offline Completed without error 00% 78 - #10 Short offline Completed without error 00% 76 - #11 Short offline Interrupted (host reset) 50% 76 - #12 Short offline Completed without error 00% 75 - #13 Short offline Completed without error 00% 69 - #14 Short offline Completed without error 00% 67 - #15 Short offline Completed without error 00% 65 - #16 Short offline Completed without error 00% 63 - #17 Short offline Completed without error 00% 58 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Aborted_by_host [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 28/39 Celsius Lifetime Min/Max Temperature: 21/64 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (126) Index Estimated Time Temperature Celsius 127 2024-06-26 23:30 39 ******************** 0 2024-06-26 23:35 35 **************** 1 2024-06-26 23:40 37 ****************** 2 2024-06-26 23:45 38 ******************* 3 2024-06-26 23:50 37 ****************** 4 2024-06-26 23:55 36 ***************** 5 2024-06-27 00:00 38 ******************* 6 2024-06-27 00:05 38 ******************* 7 2024-06-27 00:10 39 ******************** 8 2024-06-27 00:15 40 ********************* 9 2024-06-27 00:20 41 ********************** 10 2024-06-27 00:25 42 *********************** 11 2024-06-27 00:30 44 ************************* ... ..( 2 skipped). .. ************************* 14 2024-06-27 00:45 44 ************************* 15 2024-06-27 00:50 45 ************************** 16 2024-06-27 00:55 46 *************************** 17 2024-06-27 01:00 47 **************************** 18 2024-06-27 01:05 43 ************************ 19 2024-06-27 01:10 39 ******************** 20 2024-06-27 01:15 38 ******************* 21 2024-06-27 01:20 32 ************* 22 2024-06-27 01:25 36 ***************** 23 2024-06-27 01:30 39 ******************** 24 2024-06-27 01:35 40 ********************* 25 2024-06-27 01:40 42 *********************** 26 2024-06-27 01:45 43 ************************ 27 2024-06-27 01:50 43 ************************ 28 2024-06-27 01:55 44 ************************* 29 2024-06-27 02:00 44 ************************* 30 2024-06-27 02:05 43 ************************ 31 2024-06-27 02:10 44 ************************* 32 2024-06-27 02:15 32 ************* 33 2024-06-27 02:20 37 ****************** 34 2024-06-27 02:25 40 ********************* 35 2024-06-27 02:30 44 ************************* 36 2024-06-27 02:35 46 *************************** 37 2024-06-27 02:40 33 ************** 38 2024-06-27 02:45 36 ***************** 39 2024-06-27 02:50 38 ******************* 40 2024-06-27 02:55 40 ********************* 41 2024-06-27 03:00 41 ********************** 42 2024-06-27 03:05 42 *********************** 43 2024-06-27 03:10 42 *********************** 44 2024-06-27 03:15 43 ************************ ... ..( 2 skipped). .. ************************ 47 2024-06-27 03:30 43 ************************ 48 2024-06-27 03:35 42 *********************** 49 2024-06-27 03:40 41 ********************** 50 2024-06-27 03:45 41 ********************** 51 2024-06-27 03:50 42 *********************** 52 2024-06-27 03:55 42 *********************** 53 2024-06-27 04:00 43 ************************ 54 2024-06-27 04:05 44 ************************* 55 2024-06-27 04:10 43 ************************ 56 2024-06-27 04:15 44 ************************* 57 2024-06-27 04:20 44 ************************* 58 2024-06-27 04:25 45 ************************** 59 2024-06-27 04:30 42 *********************** 60 2024-06-27 04:35 43 ************************ 61 2024-06-27 04:40 43 ************************ 62 2024-06-27 04:45 44 ************************* 63 2024-06-27 04:50 45 ************************** 64 2024-06-27 04:55 33 ************** 65 2024-06-27 05:00 34 *************** ... ..( 2 skipped). .. *************** 68 2024-06-27 05:15 34 *************** 69 2024-06-27 05:20 35 **************** ... ..( 2 skipped). .. **************** 72 2024-06-27 05:35 35 **************** 73 2024-06-27 05:40 34 *************** 74 2024-06-27 05:45 34 *************** 75 2024-06-27 05:50 35 **************** ... ..( 4 skipped). .. **************** 80 2024-06-27 06:15 35 **************** 81 2024-06-27 06:20 34 *************** 82 2024-06-27 06:25 34 *************** 83 2024-06-27 06:30 34 *************** 84 2024-06-27 06:35 35 **************** 85 2024-06-27 06:40 35 **************** 86 2024-06-27 06:45 34 *************** 87 2024-06-27 06:50 35 **************** ... ..( 10 skipped). .. **************** 98 2024-06-27 07:45 35 **************** 99 2024-06-27 07:50 30 *********** 100 2024-06-27 07:55 33 ************** 101 2024-06-27 08:00 34 *************** 102 2024-06-27 08:05 35 **************** 103 2024-06-27 08:10 36 ***************** 104 2024-06-27 08:15 36 ***************** 105 2024-06-27 08:20 37 ****************** 106 2024-06-27 08:25 38 ******************* 107 2024-06-27 08:30 37 ****************** 108 2024-06-27 08:35 37 ****************** 109 2024-06-27 08:40 38 ******************* 110 2024-06-27 08:45 34 *************** 111 2024-06-27 08:50 36 ***************** 112 2024-06-27 08:55 37 ****************** 113 2024-06-27 09:00 38 ******************* 114 2024-06-27 09:05 39 ******************** 115 2024-06-27 09:10 30 *********** 116 2024-06-27 09:15 32 ************* 117 2024-06-27 09:20 33 ************** 118 2024-06-27 09:25 34 *************** 119 2024-06-27 09:30 36 ***************** 120 2024-06-27 09:35 37 ****************** 121 2024-06-27 09:40 37 ****************** 122 2024-06-27 09:45 38 ******************* 123 2024-06-27 09:50 39 ******************** 124 2024-06-27 09:55 39 ******************** 125 2024-06-27 10:00 38 ******************* 126 2024-06-27 10:05 39 ******************** SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 1 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific