/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p3 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Marvell based SanDisk SSDs Device Model: SanDisk SSD PLUS 120GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UE4500RL User Capacity: 120,040,980,480 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Nov 22 14:56:47 2022 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 28067 12 Power_Cycle_Count -O--CK 100 100 000 - 106 165 Total_Write/Erase_Count -O--CK 100 100 000 - 5015 166 Min_W/E_Cycle -O--CK 100 100 --- - 34 167 Min_Bad_Block/Die -O--CK 100 100 --- - 0 168 Maximum_Erase_Cycle -O--CK 100 100 --- - 63 169 Total_Bad_Block -O--CK 100 100 --- - 119 170 Unknown_Marvell_Attr -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Avg_Write/Erase_Count -O--CK 100 100 000 - 34 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 72 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 075 047 000 - 25 (Min/Max 12/47) 199 SATA_CRC_Error -O--CK 100 100 --- - 0 230 Perc_Write/Erase_Count -O--CK 100 100 000 - 3616 1616 3616 232 Perc_Avail_Resrvd_Space PO--CK 100 100 005 - 100 233 Total_NAND_Writes_GiB -O--CK 100 100 --- - 4049 234 Perc_Write/Erase_Ct_BC -O--CK 100 100 000 - 27901 241 Total_Writes_GiB ----CK 100 100 000 - 11427 242 Total_Reads_GiB ----CK 100 100 000 - 2312 244 Thermal_Throttle -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 106 --- Lifetime Power-On Resets 0x01 0x010 4 28067 --- Power-on Hours 0x01 0x018 6 23966020450 --- Logical Sectors Written 0x01 0x028 6 4849081871 --- Logical Sectors Read 0x01 0x038 6 28067 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 25 --- Current Temperature 0x05 0x010 1 24 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 46 --- Highest Temperature 0x05 0x028 1 18 --- Lowest Temperature 0x05 0x030 1 44 --- Highest Average Short Term Temperature 0x05 0x038 1 44 --- Lowest Average Short Term Temperature 0x05 0x040 1 29 --- Highest Average Long Term Temperature 0x05 0x048 1 29 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 6 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 34 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 35 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/ada1 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p3 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F3 Device Model: SAMSUNG HD502HJ Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AJ10001 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Nov 22 14:56:47 2022 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4620) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 77) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 19115 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 083 069 025 - 5270 4 Start_Stop_Count -O--CK 100 100 000 - 780 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 86075 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 789 191 G-Sense_Error_Rate -O---K 100 100 000 - 13 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 056 000 - 22 (Min/Max 15/44) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 184 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 100 100 000 - 796 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 48 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 48 [7] occurred at disk power-on lifetime: 24211 hours (1008 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 29 0a 9b b7 e0 00 Error: UNC 8 sectors at LBA = 0x290a9bb7 = 688561079 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 29 0a 9b b7 e0 0a 02:23:59.233 READ DMA EXT 35 00 00 00 10 00 00 24 0a 60 a7 e0 0a 02:23:59.233 WRITE DMA EXT 35 00 00 00 18 00 00 24 0a 60 47 e0 0a 02:23:59.233 WRITE DMA EXT 35 00 00 00 10 00 00 24 0a 60 27 e0 0a 02:23:59.233 WRITE DMA EXT 35 00 00 00 08 00 00 24 0a 5f d7 e0 0a 02:23:59.233 WRITE DMA EXT Error 47 [6] occurred at disk power-on lifetime: 24211 hours (1008 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 29 0a 9b b7 e0 00 Error: UNC 8 sectors at LBA = 0x290a9bb7 = 688561079 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 29 0a 9b b7 e0 0a 02:23:59.232 READ DMA EXT 25 00 00 00 08 00 00 29 0a 9c 47 e0 0a 02:23:59.232 READ DMA EXT 25 00 00 00 08 00 00 29 0a 9a ef e0 0a 02:23:59.232 READ DMA EXT 25 00 00 00 08 00 00 29 0a 9d 07 e0 0a 02:23:59.232 READ DMA EXT 25 00 00 00 08 00 00 29 0a 9b df e0 0a 02:23:59.232 READ DMA EXT Error 46 [5] occurred at disk power-on lifetime: 24211 hours (1008 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 29 0a 94 ca e0 00 Error: UNC 5 sectors at LBA = 0x290a94ca = 688559306 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 29 0a 94 c7 e0 0a 02:23:58.739 READ DMA EXT 35 00 00 00 08 00 00 22 0a 7d 8f e0 0a 02:23:58.739 WRITE DMA EXT 35 00 00 00 08 00 00 22 0a 7d 77 e0 0a 02:23:58.739 WRITE DMA EXT 35 00 00 00 08 00 00 22 0a 7d 67 e0 0a 02:23:58.739 WRITE DMA EXT 35 00 00 00 08 00 00 22 0a 7c f7 e0 0a 02:23:58.739 WRITE DMA EXT Error 45 [4] occurred at disk power-on lifetime: 24211 hours (1008 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 29 0a 94 ca e0 00 Error: UNC 5 sectors at LBA = 0x290a94ca = 688559306 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 29 0a 94 c7 e0 0a 02:23:58.737 READ DMA EXT 35 00 00 00 08 00 00 22 0a 79 8f e0 0a 02:23:58.737 WRITE DMA EXT 25 00 00 00 08 00 00 29 0a 96 af e0 0a 02:23:58.737 READ DMA EXT 25 00 00 00 08 00 00 29 0a 91 0f e0 0a 02:23:58.737 READ DMA EXT 25 00 00 00 08 00 00 29 0a 91 c7 e0 0a 02:23:58.737 READ DMA EXT Error 44 [3] occurred at disk power-on lifetime: 24211 hours (1008 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 03 00 00 29 0a 94 64 e0 00 Error: UNC 3 sectors at LBA = 0x290a9464 = 688559204 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 29 0a 94 5f e0 0a 02:23:58.724 READ DMA EXT 35 00 00 00 08 00 00 20 c9 8f e7 e0 0a 02:23:58.724 WRITE DMA EXT 35 00 00 00 08 00 00 20 c9 8f 67 e0 0a 02:23:58.724 WRITE DMA EXT ea 00 00 00 00 00 00 1d 0e a7 b6 e0 0a 02:23:58.724 FLUSH CACHE EXT 35 00 00 00 08 00 00 1d 0e a7 af e0 0a 02:23:58.724 WRITE DMA EXT Error 43 [2] occurred at disk power-on lifetime: 24211 hours (1008 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 03 00 00 29 0a 94 64 e0 00 Error: UNC 3 sectors at LBA = 0x290a9464 = 688559204 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 29 0a 94 5f e0 0a 02:23:58.722 READ DMA EXT 25 00 00 00 08 00 00 29 0a 94 9f e0 0a 02:23:58.722 READ DMA EXT 25 00 00 00 08 00 00 29 0a 90 f7 e0 0a 02:23:58.722 READ DMA EXT 25 00 00 00 08 00 00 29 0a 92 f7 e0 0a 02:23:58.722 READ DMA EXT 25 00 00 00 08 00 00 29 0a 91 6f e0 0a 02:23:58.722 READ DMA EXT Error 42 [1] occurred at disk power-on lifetime: 24211 hours (1008 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 29 8a 9d ea e0 00 Error: UNC 5 sectors at LBA = 0x298a9dea = 696950250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 29 8a 9d e7 e0 0a 02:23:58.563 READ DMA EXT 25 00 00 00 08 00 00 29 8a 9d 0f e0 0a 02:23:58.563 READ DMA EXT 25 00 00 00 08 00 00 29 8a 9e f7 e0 0a 02:23:58.563 READ DMA EXT 25 00 00 00 08 00 00 23 0a a4 1f e0 0a 02:23:58.563 READ DMA EXT 25 00 00 00 08 00 00 29 8a 9b b7 e0 0a 02:23:58.563 READ DMA EXT Error 41 [0] occurred at disk power-on lifetime: 23859 hours (994 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 29 0a 94 ca e0 00 Error: UNC 5 sectors at LBA = 0x290a94ca = 688559306 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 29 0a 94 c7 e0 0a 02:02:52.182 READ DMA EXT ea 00 00 00 00 00 00 1d 0e 02 56 e0 0a 02:02:52.181 FLUSH CACHE EXT 35 00 00 00 08 00 00 1d 0e 02 4f e0 0a 02:02:52.181 WRITE DMA EXT ea 00 00 00 00 00 00 1d 0e 02 4e e0 0a 02:02:52.181 FLUSH CACHE EXT 35 00 00 00 78 00 00 1d 0e 01 d7 e0 0a 02:02:52.181 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 17/43 Celsius Lifetime Min/Max Temperature: 17/61 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (12) Index Estimated Time Temperature Celsius 13 2022-11-22 04:20 22 *** 14 2022-11-22 04:25 22 *** 15 2022-11-22 04:30 21 ** ... ..( 72 skipped). .. ** 88 2022-11-22 10:35 21 ** 89 2022-11-22 10:40 22 *** 90 2022-11-22 10:45 21 ** ... ..( 2 skipped). .. ** 93 2022-11-22 11:00 21 ** 94 2022-11-22 11:05 22 *** ... ..( 36 skipped). .. *** 3 2022-11-22 14:10 22 *** 4 2022-11-22 14:15 21 ** 5 2022-11-22 14:20 22 *** 6 2022-11-22 14:25 21 ** 7 2022-11-22 14:30 22 *** ... ..( 4 skipped). .. *** 12 2022-11-22 14:55 22 *** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 34 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 33 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific