/dev/ada0 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.3-RELEASE-p1 amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.4 Device Model: ST9500420AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0002SDM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.5/5706 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Jul 30 17:55:36 2025 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 111) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 116 099 006 - 111459826 3 Spin_Up_Time PO---- 100 098 085 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4321 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 1 7 Seek_Error_Rate POSR-- 078 060 030 - 74132977863 9 Power_On_Hours -O--CK 057 057 000 - 38063 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 098 037 020 - 2343 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 015 015 000 - 85 188 Command_Timeout -O--CK 100 099 000 - 4295032858 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 067 046 045 - 33 (Min/Max 26/36) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 16 192 Power-Off_Retract_Count -O--CK 100 100 000 - 13 193 Load_Cycle_Count -O--CK 001 001 000 - 805397 194 Temperature_Celsius -O---K 033 054 000 - 33 (0 14 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 044 031 000 - 111459826 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 314 240 Head_Flying_Hours ------ 100 253 000 - 36208 (24 115 0) 241 Total_LBAs_Written ------ 100 253 000 - 3053683233 242 Total_LBAs_Read ------ 100 253 000 - 1067775417 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 62 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 62 [1] occurred at disk power-on lifetime: 18223 hours (759 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 13 ab 00 1c 12 00 00 Error: UNC at LBA = 0x13ab001c12 = 84473289746 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:40.788 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:37.999 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:35.276 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:32.537 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:29.838 READ DMA EXT Error 61 [0] occurred at disk power-on lifetime: 18223 hours (759 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 13 ab 00 1c 12 00 00 Error: UNC at LBA = 0x13ab001c12 = 84473289746 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:37.999 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:35.276 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:32.537 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:29.838 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 11 40 00 00:08:29.836 READ DMA EXT Error 60 [19] occurred at disk power-on lifetime: 18223 hours (759 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 13 ab 00 1c 12 00 00 Error: UNC at LBA = 0x13ab001c12 = 84473289746 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:35.276 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:32.537 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:29.838 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 11 40 00 00:08:29.836 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 10 40 00 00:08:29.835 READ DMA EXT Error 59 [18] occurred at disk power-on lifetime: 18223 hours (759 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 13 ab 00 1c 12 00 00 Error: UNC at LBA = 0x13ab001c12 = 84473289746 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 13 ab 00 1c 12 40 00 00:08:29.838 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 11 40 00 00:08:29.836 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 10 40 00 00:08:29.835 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 0f 40 00 00:08:29.835 READ DMA EXT 25 00 00 00 01 00 13 ab 00 1c 0e 40 00 00:08:29.835 READ DMA EXT Error 58 [17] occurred at disk power-on lifetime: 18223 hours (759 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 13 ab 00 1c 12 00 00 Error: UNC at LBA = 0x13ab001c12 = 84473289746 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:26.984 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:24.179 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:21.448 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:18.642 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:15.947 READ DMA EXT Error 57 [16] occurred at disk power-on lifetime: 18223 hours (759 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 13 ab 00 1c 12 00 00 Error: UNC at LBA = 0x13ab001c12 = 84473289746 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:24.179 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:21.448 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:18.642 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:15.947 READ DMA EXT 25 00 00 00 40 00 13 aa 00 1c a8 40 00 00:08:15.927 READ DMA EXT Error 56 [15] occurred at disk power-on lifetime: 18223 hours (759 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 13 ab 00 1c 12 00 00 Error: UNC at LBA = 0x13ab001c12 = 84473289746 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:21.448 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:18.642 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:15.947 READ DMA EXT 25 00 00 00 40 00 13 aa 00 1c a8 40 00 00:08:15.927 READ DMA EXT 25 00 00 00 80 00 13 35 00 09 a8 40 00 00:08:15.920 READ DMA EXT Error 55 [14] occurred at disk power-on lifetime: 18223 hours (759 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 13 ab 00 1c 12 00 00 Error: UNC at LBA = 0x13ab001c12 = 84473289746 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:18.642 READ DMA EXT 25 00 00 00 80 00 13 aa 00 1c e8 40 00 00:08:15.947 READ DMA EXT 25 00 00 00 40 00 13 aa 00 1c a8 40 00 00:08:15.927 READ DMA EXT 25 00 00 00 80 00 13 35 00 09 a8 40 00 00:08:15.920 READ DMA EXT 25 00 00 00 80 00 13 35 00 09 28 40 00 00:08:15.909 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 9422 - # 2 Short offline Completed without error 00% 9414 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 26/36 Celsius Lifetime Min/Max Temperature: 14/54 Celsius Specified Max Operating Temperature: 31 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (57) Index Estimated Time Temperature Celsius 58 2025-07-30 15:48 36 ***************** 59 2025-07-30 15:49 35 **************** ... ..( 2 skipped). .. **************** 62 2025-07-30 15:52 35 **************** 63 2025-07-30 15:53 34 *************** 64 2025-07-30 15:54 34 *************** 65 2025-07-30 15:55 34 *************** 66 2025-07-30 15:56 33 ************** ... ..( 7 skipped). .. ************** 74 2025-07-30 16:04 33 ************** 75 2025-07-30 16:05 32 ************* ... ..( 42 skipped). .. ************* 118 2025-07-30 16:48 32 ************* 119 2025-07-30 16:49 33 ************** ... ..( 15 skipped). .. ************** 7 2025-07-30 17:05 33 ************** 8 2025-07-30 17:06 32 ************* ... ..( 48 skipped). .. ************* 57 2025-07-30 17:55 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 20 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS