/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: JMicron/Maxiotek based SSDs Device Model: ADATA SP600 Serial Number: -- LU WWN Device Id: 5 707c18 ... Firmware Version: 2.9 User Capacity: 32,017,047,552 bytes [32.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: < 1.8 inches TRIM Command: Available Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Nov 23 22:22:22 2023 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 32) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Unknown_JMF_Attribute POS--- 100 100 050 - 0 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 7 Unknown_JMF_Attribute PO-R-- 100 100 050 - 0 8 Unknown_JMF_Attribute P-S--- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 43235 10 Unknown_JMF_Attribute PO--C- 100 100 050 - 0 12 Power_Cycle_Count -O--C- 100 100 000 - 473 167 Unknown_JMF_Attribute -O---K 100 100 000 - 0 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 148 169 Unknown_JMF_Attribute PO--C- 100 100 010 - 4295163906 170 Bad_Block_Count PO--C- 100 100 010 - 0 0 0 173 Erase_Count -O--C- 001 001 000 - 7067 7736 7181 175 Bad_Cluster_Table_Count PO--C- 100 100 010 - 0 192 Unexpect_Power_Loss_Ct -O--C- 100 100 000 - 190 194 Temperature_Celsius -O---K 064 064 030 - 36 (Min/Max 29/40) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 240 Unknown_JMF_Attribute PO--C- 100 100 050 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 266 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 266 [9] occurred at disk power-on lifetime: 42647 hours (1776 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b7 6d 60 40 00 Error: UNC at LBA = 0x02b76d60 = 45575520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 58 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 50 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 48 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 40 40 00 01:38:52.600 READ DMA EXT Error 265 [8] occurred at disk power-on lifetime: 42647 hours (1776 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b7 6c a0 40 00 Error: UNC at LBA = 0x02b76ca0 = 45575328 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 da 01 00 00 00 02 b7 6c a0 40 00 01:38:51.500 READ DMA EXT 25 00 da 01 00 00 00 02 b7 6b a0 40 00 01:38:51.500 READ DMA EXT 25 00 da 01 00 00 00 02 b7 6a a0 40 00 01:38:51.500 READ DMA EXT 25 00 da 01 00 00 00 02 b7 69 a0 40 00 01:38:49.600 READ DMA EXT 25 00 da 01 00 00 00 02 b7 68 a0 40 00 01:38:49.600 READ DMA EXT Error 264 [7] occurred at disk power-on lifetime: 42647 hours (1776 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b7 6d 60 40 00 Error: UNC at LBA = 0x02b76d60 = 45575520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 58 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 50 40 00 01:38:52.600 READ DMA EXT Error 263 [6] occurred at disk power-on lifetime: 42647 hours (1776 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b7 6d 60 40 00 Error: UNC at LBA = 0x02b76d60 = 45575520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 58 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 50 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 48 40 00 01:38:52.600 READ DMA EXT Error 262 [5] occurred at disk power-on lifetime: 42647 hours (1776 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b7 6d 60 40 00 Error: UNC at LBA = 0x02b76d60 = 45575520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 58 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 50 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 48 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 40 40 00 01:38:52.600 READ DMA EXT Error 261 [4] occurred at disk power-on lifetime: 42647 hours (1776 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b7 6c a0 40 00 Error: UNC at LBA = 0x02b76ca0 = 45575328 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 da 01 00 00 00 02 b7 6c a0 40 00 01:38:51.500 READ DMA EXT 25 00 da 01 00 00 00 02 b7 6b a0 40 00 01:38:51.500 READ DMA EXT 25 00 da 01 00 00 00 02 b7 6a a0 40 00 01:38:51.500 READ DMA EXT 25 00 da 01 00 00 00 02 b7 69 a0 40 00 01:38:49.600 READ DMA EXT 25 00 da 01 00 00 00 02 b7 68 a0 40 00 01:38:49.600 READ DMA EXT Error 260 [3] occurred at disk power-on lifetime: 42647 hours (1776 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b7 6d 60 40 00 Error: UNC at LBA = 0x02b76d60 = 45575520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 58 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 50 40 00 01:38:52.600 READ DMA EXT Error 259 [2] occurred at disk power-on lifetime: 42647 hours (1776 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 b7 6d 60 40 00 Error: UNC at LBA = 0x02b76d60 = 45575520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 60 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 58 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 50 40 00 01:38:52.600 READ DMA EXT 25 00 da 00 08 00 00 02 b7 6d 48 40 00 01:38:52.600 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: --/ 0 Celsius Lifetime Min/Max Temperature: --/ 0 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -127/127 Celsius Min/Max Temperature Limit: -127/127 Celsius Temperature History Size (Index): 478 (55) Index Estimated Time Temperature Celsius 56 2023-11-23 14:25 37 ****************** 57 2023-11-23 14:26 38 ******************* ... ..(111 skipped). .. ******************* 169 2023-11-23 16:18 38 ******************* 170 2023-11-23 16:19 37 ****************** ... ..( 4 skipped). .. ****************** 175 2023-11-23 16:24 37 ****************** 176 2023-11-23 16:25 38 ******************* 177 2023-11-23 16:26 37 ****************** ... ..( 74 skipped). .. ****************** 252 2023-11-23 17:41 37 ****************** 253 2023-11-23 17:42 38 ******************* 254 2023-11-23 17:43 38 ******************* 255 2023-11-23 17:44 38 ******************* 256 2023-11-23 17:45 37 ****************** 257 2023-11-23 17:46 38 ******************* ... ..( 2 skipped). .. ******************* 260 2023-11-23 17:49 38 ******************* 261 2023-11-23 17:50 37 ****************** ... ..( 5 skipped). .. ****************** 267 2023-11-23 17:56 37 ****************** 268 2023-11-23 17:57 38 ******************* ... ..( 5 skipped). .. ******************* 274 2023-11-23 18:03 38 ******************* 275 2023-11-23 18:04 37 ****************** ... ..( 3 skipped). .. ****************** 279 2023-11-23 18:08 37 ****************** 280 2023-11-23 18:09 38 ******************* ... ..( 31 skipped). .. ******************* 312 2023-11-23 18:41 38 ******************* 313 2023-11-23 18:42 39 ******************** 314 2023-11-23 18:43 39 ******************** 315 2023-11-23 18:44 38 ******************* 316 2023-11-23 18:45 38 ******************* 317 2023-11-23 18:46 38 ******************* 318 2023-11-23 18:47 39 ******************** 319 2023-11-23 18:48 39 ******************** 320 2023-11-23 18:49 39 ******************** 321 2023-11-23 18:50 38 ******************* 322 2023-11-23 18:51 39 ******************** ... ..( 13 skipped). .. ******************** 336 2023-11-23 19:05 39 ******************** 337 2023-11-23 19:06 38 ******************* 338 2023-11-23 19:07 38 ******************* 339 2023-11-23 19:08 38 ******************* 340 2023-11-23 19:09 39 ******************** ... ..( 30 skipped). .. ******************** 371 2023-11-23 19:40 39 ******************** 372 2023-11-23 19:41 38 ******************* ... ..( 2 skipped). .. ******************* 375 2023-11-23 19:44 38 ******************* 376 2023-11-23 19:45 39 ******************** ... ..( 5 skipped). .. ******************** 382 2023-11-23 19:51 39 ******************** 383 2023-11-23 19:52 38 ******************* ... ..( 6 skipped). .. ******************* 390 2023-11-23 19:59 38 ******************* 391 2023-11-23 20:00 39 ******************** ... ..( 8 skipped). .. ******************** 400 2023-11-23 20:09 39 ******************** 401 2023-11-23 20:10 38 ******************* ... ..( 2 skipped). .. ******************* 404 2023-11-23 20:13 38 ******************* 405 2023-11-23 20:14 39 ******************** ... ..( 7 skipped). .. ******************** 413 2023-11-23 20:22 39 ******************** 414 2023-11-23 20:23 38 ******************* 415 2023-11-23 20:24 38 ******************* 416 2023-11-23 20:25 39 ******************** ... ..( 16 skipped). .. ******************** 433 2023-11-23 20:42 39 ******************** 434 2023-11-23 20:43 38 ******************* ... ..( 3 skipped). .. ******************* 438 2023-11-23 20:47 38 ******************* 439 2023-11-23 20:48 39 ******************** ... ..( 26 skipped). .. ******************** 466 2023-11-23 21:15 39 ******************** 467 2023-11-23 21:16 38 ******************* ... ..( 4 skipped). .. ******************* 472 2023-11-23 21:21 38 ******************* 473 2023-11-23 21:22 37 ****************** 474 2023-11-23 21:23 37 ****************** 475 2023-11-23 21:24 37 ****************** 476 2023-11-23 21:25 ? - 477 2023-11-23 21:26 31 ************ 0 2023-11-23 21:27 32 ************* 1 2023-11-23 21:28 33 ************** 2 2023-11-23 21:29 33 ************** 3 2023-11-23 21:30 34 *************** 4 2023-11-23 21:31 34 *************** 5 2023-11-23 21:32 34 *************** 6 2023-11-23 21:33 35 **************** ... ..( 4 skipped). .. **************** 11 2023-11-23 21:38 35 **************** 12 2023-11-23 21:39 36 ***************** 13 2023-11-23 21:40 35 **************** 14 2023-11-23 21:41 36 ***************** ... ..( 22 skipped). .. ***************** 37 2023-11-23 22:04 36 ***************** 38 2023-11-23 22:05 37 ****************** 39 2023-11-23 22:06 36 ***************** ... ..( 2 skipped). .. ***************** 42 2023-11-23 22:09 36 ***************** 43 2023-11-23 22:10 37 ****************** 44 2023-11-23 22:11 36 ***************** ... ..( 10 skipped). .. ***************** 55 2023-11-23 22:22 36 ***************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 473 --- Lifetime Power-On Resets 0x01 0x018 6 403744860821 --- Logical Sectors Written 0x01 0x020 6 2155132365 --- Number of Write Commands 0x01 0x028 6 925873652 --- Logical Sectors Read 0x01 0x030 6 12839544 --- Number of Read Commands 0x01 0x038 6 155646000000 --- Date and Time TimeStamp 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 255 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 148 Command failed due to ICRC error 0x0003 2 2 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 32 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC