/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.2-RELEASE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9320325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0003SDM1 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Jun 7 14:18:06 2023 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 95) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 086 006 - 128094528 3 Spin_Up_Time PO---- 099 098 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 9808 5 Reallocated_Sector_Ct PO--CK 096 096 036 - 92 7 Seek_Error_Rate POSR-- 085 060 030 - 4669498421 9 Power_On_Hours -O--CK 071 071 000 - 25836 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 091 091 020 - 9563 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 2215 188 Command_Timeout -O--CK 100 097 000 - 179 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 061 047 045 - 39 (Min/Max 38/41) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 852 192 Power-Off_Retract_Count -O--CK 100 100 000 - 1595 193 Load_Cycle_Count -O--CK 001 001 000 - 229868 194 Temperature_Celsius -O---K 039 053 000 - 39 (0 8 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 066 052 000 - 128094528 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 2412 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2412 [11] occurred at disk power-on lifetime: 23455 hours (977 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 b5 00 52 11 be 00 00 Error: UNC at LBA = 0xb5005211be = 777394459070 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 b5 00 52 11 b8 40 00 00:06:19.742 READ FPDMA QUEUED 61 00 00 00 08 00 91 00 4f 12 f8 40 00 00:06:19.742 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:06:19.742 FLUSH CACHE EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:06:19.741 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:06:19.740 IDENTIFY DEVICE Error 2411 [10] occurred at disk power-on lifetime: 23455 hours (977 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 b5 00 52 11 be 00 00 Error: UNC at LBA = 0xb5005211be = 777394459070 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 b5 00 52 11 b8 40 00 00:06:17.319 READ FPDMA QUEUED 61 00 00 00 c8 00 91 00 4f 12 30 40 00 00:06:17.319 WRITE FPDMA QUEUED 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:06:17.318 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:06:17.316 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:06:17.284 SET FEATURES [Set transfer mode] Error 2410 [9] occurred at disk power-on lifetime: 23455 hours (977 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 b5 00 52 11 be 00 00 Error: UNC at LBA = 0xb5005211be = 777394459070 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 b5 00 52 11 b8 40 00 00:06:14.737 READ FPDMA QUEUED 60 00 00 00 08 00 b5 00 52 11 b0 40 00 00:06:14.737 READ FPDMA QUEUED 60 00 00 00 08 00 b5 00 52 11 a8 40 00 00:06:14.737 READ FPDMA QUEUED 60 00 00 00 08 00 b5 00 52 11 a0 40 00 00:06:14.736 READ FPDMA QUEUED 60 00 00 00 08 00 b5 00 52 11 98 40 00 00:06:14.736 READ FPDMA QUEUED Error 2409 [8] occurred at disk power-on lifetime: 23455 hours (977 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 b5 00 52 11 be 00 00 Error: UNC at LBA = 0xb5005211be = 777394459070 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 b5 00 53 11 68 40 00 00:06:12.132 READ FPDMA QUEUED 60 00 00 01 00 00 b5 00 52 11 68 40 00 00:06:12.130 READ FPDMA QUEUED 60 00 00 01 00 00 b5 00 51 11 68 40 00 00:06:12.129 READ FPDMA QUEUED 60 00 00 01 00 00 b5 00 50 11 68 40 00 00:06:12.128 READ FPDMA QUEUED 60 00 00 01 00 00 b5 00 4f 11 68 40 00 00:06:12.128 READ FPDMA QUEUED Error 2408 [7] occurred at disk power-on lifetime: 23454 hours (977 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 ba 00 fd 11 a8 00 00 Error: UNC at LBA = 0xba00fd11a8 = 798880502184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 ba 00 fd 11 a8 40 00 01:11:53.509 READ FPDMA QUEUED 61 00 00 00 08 00 90 00 72 12 18 40 00 01:11:53.509 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 01:11:53.509 FLUSH CACHE EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:11:53.508 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:11:53.506 IDENTIFY DEVICE Error 2407 [6] occurred at disk power-on lifetime: 23454 hours (977 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 ba 00 fd 11 a8 00 00 Error: UNC at LBA = 0xba00fd11a8 = 798880502184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 ba 00 fd 11 a8 40 00 01:11:51.088 READ FPDMA QUEUED 61 00 00 00 f8 00 90 00 71 12 20 40 00 01:11:51.088 WRITE FPDMA QUEUED 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:11:51.087 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:11:51.086 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:11:51.085 SET FEATURES [Set transfer mode] Error 2406 [5] occurred at disk power-on lifetime: 23454 hours (977 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 ba 00 fd 11 a8 00 00 Error: UNC at LBA = 0xba00fd11a8 = 798880502184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 ba 00 fd 11 a8 40 00 01:11:48.599 READ FPDMA QUEUED 60 00 00 00 08 00 01 00 1b 01 b8 40 00 01:11:46.940 READ FPDMA QUEUED 61 00 00 00 20 00 10 00 17 22 08 40 00 01:11:46.924 WRITE FPDMA QUEUED 60 00 00 00 40 00 6b 00 02 00 10 40 00 01:11:46.922 READ FPDMA QUEUED 60 00 00 00 18 00 6b 00 01 00 f0 40 00 01:11:46.922 READ FPDMA QUEUED Error 2405 [4] occurred at disk power-on lifetime: 23454 hours (977 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 ba 00 fd 11 a8 00 00 Error: UNC at LBA = 0xba00fd11a8 = 798880502184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 ba 00 fd 11 a8 40 00 01:10:36.059 READ FPDMA QUEUED 60 00 00 01 00 00 c1 00 15 03 e0 40 00 01:10:36.053 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 01:10:36.030 FLUSH CACHE EXT 60 00 00 00 58 00 c1 00 15 03 88 40 00 01:10:36.009 READ FPDMA QUEUED 61 00 00 00 08 00 90 00 67 12 c0 40 00 01:10:36.009 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 38/41 Celsius Lifetime Min/Max Temperature: 8/54 Celsius Under/Over Temperature Limit Count: 0/94 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (119) Index Estimated Time Temperature Celsius 120 2023-06-07 12:11 39 ******************** 121 2023-06-07 12:12 40 ********************* ... ..( 6 skipped). .. ********************* 0 2023-06-07 12:19 40 ********************* 1 2023-06-07 12:20 39 ******************** ... ..( 15 skipped). .. ******************** 17 2023-06-07 12:36 39 ******************** 18 2023-06-07 12:37 40 ********************* 19 2023-06-07 12:38 39 ******************** ... ..( 2 skipped). .. ******************** 22 2023-06-07 12:41 39 ******************** 23 2023-06-07 12:42 ? - 24 2023-06-07 12:43 39 ******************** 25 2023-06-07 12:44 ? - 26 2023-06-07 12:45 38 ******************* 27 2023-06-07 12:46 38 ******************* 28 2023-06-07 12:47 38 ******************* 29 2023-06-07 12:48 39 ******************** 30 2023-06-07 12:49 39 ******************** 31 2023-06-07 12:50 39 ******************** 32 2023-06-07 12:51 40 ********************* ... ..( 4 skipped). .. ********************* 37 2023-06-07 12:56 40 ********************* 38 2023-06-07 12:57 41 ********************** ... ..( 7 skipped). .. ********************** 46 2023-06-07 13:05 41 ********************** 47 2023-06-07 13:06 40 ********************* 48 2023-06-07 13:07 40 ********************* 49 2023-06-07 13:08 40 ********************* 50 2023-06-07 13:09 39 ******************** ... ..( 18 skipped). .. ******************** 69 2023-06-07 13:28 39 ******************** 70 2023-06-07 13:29 38 ******************* ... ..( 27 skipped). .. ******************* 98 2023-06-07 13:57 38 ******************* 99 2023-06-07 13:58 39 ******************** ... ..( 19 skipped). .. ******************** 119 2023-06-07 14:18 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 16 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS