/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE-p5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.B Device Model: Hitachi HDT721010SLA360 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: ST6OA31B User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Jan 29 18:44:10 2025 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14090) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 235) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 100 100 054 - 0 3 Spin_Up_Time POS--- 143 143 024 - 475 (Average 329) 4 Start_Stop_Count -O--C- 099 099 000 - 5457 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 099 099 000 - 8724 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 5420 192 Power-Off_Retract_Count -O--CK 096 096 000 - 5490 193 Load_Cycle_Count -O--C- 096 096 000 - 5490 194 Temperature_Celsius -O---- 240 240 000 - 25 (Min/Max 16/64) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 6 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [1] occurred at disk power-on lifetime: 5369 hours (223 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 24 00 00 02 24 4a ad e2 00 Error: UNC 36 sectors at LBA = 0x02244aad = 35932845 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 7f 00 00 02 24 4a 52 e0 00 00:00:43.200 READ DMA EXT 25 00 00 00 7f 00 00 02 24 49 d3 e0 00 00:00:43.200 READ DMA EXT 25 00 00 00 7f 00 00 02 24 49 54 e0 00 00:00:43.200 READ DMA EXT 25 00 00 00 7f 00 00 02 24 48 d5 e0 00 00:00:43.200 READ DMA EXT 25 00 00 00 7f 00 00 02 24 48 56 e0 00 00:00:43.200 READ DMA EXT Error 5 [0] occurred at disk power-on lifetime: 5369 hours (223 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 24 00 00 02 24 4a ad e2 00 Error: UNC 36 sectors at LBA = 0x02244aad = 35932845 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 7f 00 00 02 24 4a 52 e0 00 00:00:33.900 READ DMA EXT 25 00 00 00 7f 00 00 02 24 49 d3 e0 00 00:00:33.900 READ DMA EXT 25 00 00 00 7f 00 00 02 24 49 54 e0 00 00:00:33.900 READ DMA EXT 25 00 00 00 7f 00 00 02 24 48 d5 e0 00 00:00:33.900 READ DMA EXT 25 00 00 00 7f 00 00 02 24 48 56 e0 00 00:00:33.900 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 5369 hours (223 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 24 00 00 02 24 4a ad e2 00 Error: UNC 36 sectors at LBA = 0x02244aad = 35932845 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 7f 00 00 02 24 4a 52 e0 00 00:00:24.500 READ DMA EXT 25 00 00 00 7f 00 00 02 24 49 d3 e0 00 00:00:24.500 READ DMA EXT 25 00 00 00 7f 00 00 02 24 49 54 e0 00 00:00:24.500 READ DMA EXT 25 00 00 00 7f 00 00 02 24 48 d5 e0 00 00:00:24.500 READ DMA EXT 25 00 00 00 7f 00 00 02 24 48 56 e0 00 00:00:24.500 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 5369 hours (223 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 24 00 00 02 24 4a ad e2 00 Error: UNC 36 sectors at LBA = 0x02244aad = 35932845 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 7f 00 00 02 24 4a 52 e0 00 00:00:37.800 READ DMA EXT 25 00 00 00 7f 00 00 02 24 49 d3 e0 00 00:00:37.800 READ DMA EXT 25 00 00 00 7f 00 00 02 24 49 54 e0 00 00:00:37.800 READ DMA EXT 25 00 00 00 7f 00 00 02 24 48 d5 e0 00 00:00:37.800 READ DMA EXT 25 00 00 00 7f 00 00 02 24 48 56 e0 00 00:00:37.800 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 23/25 Celsius Lifetime Min/Max Temperature: 16/64 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (22) Index Estimated Time Temperature Celsius 23 2025-01-29 16:37 31 ************ 24 2025-01-29 16:38 32 ************* 25 2025-01-29 16:39 ? - 26 2025-01-29 16:40 20 * 27 2025-01-29 16:41 21 ** 28 2025-01-29 16:42 22 *** 29 2025-01-29 16:43 23 **** 30 2025-01-29 16:44 23 **** 31 2025-01-29 16:45 24 ***** 32 2025-01-29 16:46 25 ****** 33 2025-01-29 16:47 25 ****** 34 2025-01-29 16:48 26 ******* 35 2025-01-29 16:49 27 ******** 36 2025-01-29 16:50 27 ******** 37 2025-01-29 16:51 ? - 38 2025-01-29 16:52 22 *** 39 2025-01-29 16:53 23 **** 40 2025-01-29 16:54 24 ***** 41 2025-01-29 16:55 25 ****** 42 2025-01-29 16:56 25 ****** 43 2025-01-29 16:57 26 ******* 44 2025-01-29 16:58 27 ******** 45 2025-01-29 16:59 27 ******** 46 2025-01-29 17:00 28 ********* 47 2025-01-29 17:01 29 ********** 48 2025-01-29 17:02 29 ********** 49 2025-01-29 17:03 30 *********** 50 2025-01-29 17:04 31 ************ 51 2025-01-29 17:05 31 ************ 52 2025-01-29 17:06 32 ************* 53 2025-01-29 17:07 32 ************* 54 2025-01-29 17:08 33 ************** 55 2025-01-29 17:09 34 *************** 56 2025-01-29 17:10 34 *************** 57 2025-01-29 17:11 35 **************** 58 2025-01-29 17:12 35 **************** 59 2025-01-29 17:13 35 **************** 60 2025-01-29 17:14 36 ***************** 61 2025-01-29 17:15 36 ***************** 62 2025-01-29 17:16 36 ***************** 63 2025-01-29 17:17 37 ****************** 64 2025-01-29 17:18 37 ****************** 65 2025-01-29 17:19 37 ****************** 66 2025-01-29 17:20 38 ******************* 67 2025-01-29 17:21 38 ******************* 68 2025-01-29 17:22 39 ******************** 69 2025-01-29 17:23 39 ******************** 70 2025-01-29 17:24 39 ******************** 71 2025-01-29 17:25 40 ********************* ... ..( 2 skipped). .. ********************* 74 2025-01-29 17:28 40 ********************* 75 2025-01-29 17:29 41 ********************** ... ..( 3 skipped). .. ********************** 79 2025-01-29 17:33 41 ********************** 80 2025-01-29 17:34 42 *********************** ... ..( 3 skipped). .. *********************** 84 2025-01-29 17:38 42 *********************** 85 2025-01-29 17:39 43 ************************ ... ..( 4 skipped). .. ************************ 90 2025-01-29 17:44 43 ************************ 91 2025-01-29 17:45 44 ************************* ... ..( 5 skipped). .. ************************* 97 2025-01-29 17:51 44 ************************* 98 2025-01-29 17:52 45 ************************** ... ..( 2 skipped). .. ************************** 101 2025-01-29 17:55 45 ************************** 102 2025-01-29 17:56 46 *************************** ... ..( 10 skipped). .. *************************** 113 2025-01-29 18:07 46 *************************** 114 2025-01-29 18:08 47 **************************** ... ..( 10 skipped). .. **************************** 125 2025-01-29 18:19 47 **************************** 126 2025-01-29 18:20 48 ***************************** ... ..( 8 skipped). .. ***************************** 7 2025-01-29 18:29 48 ***************************** 8 2025-01-29 18:30 49 ****************************** 9 2025-01-29 18:31 48 ***************************** 10 2025-01-29 18:32 48 ***************************** 11 2025-01-29 18:33 49 ****************************** ... ..( 6 skipped). .. ****************************** 18 2025-01-29 18:40 49 ****************************** 19 2025-01-29 18:41 ? - 20 2025-01-29 18:42 23 **** 21 2025-01-29 18:43 24 ***** 22 2025-01-29 18:44 25 ****** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS