/dev/ada0 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.2-RELEASE amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue / Red / Green SSDs Device Model: WDC WDS240G2G0A-00JH30 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UF220400 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.5/5706 ATA Version is: ACS-3, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 22 16:15:05 2025 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 41) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 5 9 Power_On_Hours -O--CK 100 100 000 - 3638 12 Power_Cycle_Count -O--CK 100 100 000 - 2496 165 Block_Erase_Count -O--CK 100 100 000 - 1880 166 Minimum_PE_Cycles_TLC -O--CK 100 100 --- - 26 167 Max_Bad_Blocks_per_Die -O--CK 100 100 --- - 15 168 Maximum_PE_Cycles_TLC -O--CK 100 100 --- - 41 169 Total_Bad_Blocks -O--CK 100 100 --- - 106 170 Grown_Bad_Blocks -O--CK 100 100 --- - 5 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 000 - 26 174 Unexpected_Power_Loss -O--CK 100 100 000 - 1123 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 059 061 000 - 41 (Min/Max 7/61) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x052505140525 232 Available_Reservd_Space PO--CK 100 100 005 - 98 233 NAND_GB_Written_TLC -O--CK 100 100 --- - 6544 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 14985 241 Host_Writes_GiB ----CK 100 100 000 - 5694 242 Host_Reads_GiB ----CK 100 100 000 - 5757 244 Temp_Throttle_Status -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa4 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 4 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2496 --- Lifetime Power-On Resets 0x01 0x010 4 3638 --- Power-on Hours 0x01 0x018 6 11941461129 --- Logical Sectors Written 0x01 0x028 6 12073707658 --- Logical Sectors Read 0x01 0x038 6 3638 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 61 --- Highest Temperature 0x05 0x028 1 21 --- Lowest Temperature 0x05 0x030 1 47 --- Highest Average Short Term Temperature 0x05 0x038 1 47 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 5 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 27 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/da0 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.2-RELEASE amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: HGST Travelstar 7K1000 Device Model: HGST HTS721010A9E630 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JB0OA3U0 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.5/5706 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 22 16:15:05 2025 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 171) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 253 253 033 - 0 4 Start_Stop_Count -O--C- 099 099 000 - 2091 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 066 066 000 - 15298 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1732 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 098 098 000 - 458 193 Load_Cycle_Count -O--C- 084 084 000 - 160991 194 Temperature_Celsius -O---- 157 157 000 - 38 (Min/Max 3/53) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 619 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 622 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 622 [1] occurred at disk power-on lifetime: 15284 hours (636 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 28 00 00 23 9f f5 e8 03 00 Error: ICRC, ABRT at LBA = 0x239ff5e8 = 597685736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 88 00 30 00 00 23 9f f5 88 40 00 00:06:31.102 WRITE FPDMA QUEUED 61 00 30 00 30 00 00 23 9f f5 50 40 00 00:06:31.102 WRITE FPDMA QUEUED 61 00 58 00 30 00 00 23 9f f4 f0 40 00 00:06:31.101 WRITE FPDMA QUEUED 61 00 08 00 30 00 00 23 9f f4 e0 40 00 00:06:31.101 WRITE FPDMA QUEUED 61 00 40 00 30 00 00 23 9f f3 78 40 00 00:06:31.101 WRITE FPDMA QUEUED Error 621 [0] occurred at disk power-on lifetime: 15284 hours (636 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 18 00 00 23 9f f0 00 03 00 Error: ICRC, ABRT at LBA = 0x239ff000 = 597684224 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 88 00 10 00 00 23 9f ef 90 40 00 00:02:23.753 WRITE FPDMA QUEUED 61 00 18 00 08 00 00 23 9f ef 70 40 00 00:02:23.753 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 23 9f ee 90 40 00 00:02:23.749 WRITE FPDMA QUEUED 61 00 10 00 08 00 00 23 9f ef 30 40 00 00:02:23.749 WRITE FPDMA QUEUED 61 00 10 00 08 00 00 23 9f ef 18 40 00 00:02:23.749 WRITE FPDMA QUEUED Error 620 [3] occurred at disk power-on lifetime: 15284 hours (636 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 28 00 00 25 db a2 c8 05 00 Error: ICRC, ABRT at LBA = 0x25dba2c8 = 635151048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 08 00 00 28 b9 20 00 40 00 00:01:51.679 READ FPDMA QUEUED 60 00 08 00 00 00 00 28 7b 78 b8 40 00 00:01:51.678 READ FPDMA QUEUED 60 00 08 00 68 00 00 27 9c 0e 40 40 00 00:01:51.678 READ FPDMA QUEUED 61 00 68 00 60 00 00 25 db a2 88 40 00 00:01:51.678 WRITE FPDMA QUEUED 61 00 18 00 58 00 00 23 9f e0 98 40 00 00:01:51.678 WRITE FPDMA QUEUED Error 619 [2] occurred at disk power-on lifetime: 15284 hours (636 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 23 9f e0 a8 03 00 Error: ICRC, ABRT at LBA = 0x239fe0a8 = 597680296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 50 00 58 00 00 23 9f e2 88 40 00 00:01:17.204 WRITE FPDMA QUEUED 61 00 40 00 50 00 00 23 9f e2 40 40 00 00:01:17.204 WRITE FPDMA QUEUED 61 00 08 00 48 00 00 23 9f e2 20 40 00 00:01:17.204 WRITE FPDMA QUEUED 61 00 20 00 40 00 00 23 9f e1 f8 40 00 00:01:17.204 WRITE FPDMA QUEUED 61 00 98 00 38 00 00 23 9f e1 58 40 00 00:01:17.204 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 25/39 Celsius Lifetime Min/Max Temperature: 3/53 Celsius Specified Max Operating Temperature: 25 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (59) Index Estimated Time Temperature Celsius 60 2025-06-22 14:08 40 ********************* 61 2025-06-22 14:09 40 ********************* 62 2025-06-22 14:10 39 ******************** 63 2025-06-22 14:11 39 ******************** 64 2025-06-22 14:12 38 ******************* 65 2025-06-22 14:13 ? - 66 2025-06-22 14:14 25 ****** 67 2025-06-22 14:15 26 ******* 68 2025-06-22 14:16 28 ********* 69 2025-06-22 14:17 29 ********** 70 2025-06-22 14:18 30 *********** 71 2025-06-22 14:19 30 *********** 72 2025-06-22 14:20 31 ************ 73 2025-06-22 14:21 31 ************ 74 2025-06-22 14:22 32 ************* ... ..( 2 skipped). .. ************* 77 2025-06-22 14:25 32 ************* 78 2025-06-22 14:26 33 ************** ... ..( 2 skipped). .. ************** 81 2025-06-22 14:29 33 ************** 82 2025-06-22 14:30 34 *************** ... ..( 3 skipped). .. *************** 86 2025-06-22 14:34 34 *************** 87 2025-06-22 14:35 35 **************** ... ..( 7 skipped). .. **************** 95 2025-06-22 14:43 35 **************** 96 2025-06-22 14:44 36 ***************** 97 2025-06-22 14:45 37 ****************** ... ..( 35 skipped). .. ****************** 5 2025-06-22 15:21 37 ****************** 6 2025-06-22 15:22 36 ***************** ... ..( 4 skipped). .. ***************** 11 2025-06-22 15:27 36 ***************** 12 2025-06-22 15:28 37 ****************** 13 2025-06-22 15:29 36 ***************** 14 2025-06-22 15:30 37 ****************** ... ..( 5 skipped). .. ****************** 20 2025-06-22 15:36 37 ****************** 21 2025-06-22 15:37 36 ***************** 22 2025-06-22 15:38 36 ***************** 23 2025-06-22 15:39 37 ****************** ... ..( 19 skipped). .. ****************** 43 2025-06-22 15:59 37 ****************** 44 2025-06-22 16:00 38 ******************* 45 2025-06-22 16:01 38 ******************* 46 2025-06-22 16:02 39 ******************** ... ..( 7 skipped). .. ******************** 54 2025-06-22 16:10 39 ******************** 55 2025-06-22 16:11 38 ******************* 56 2025-06-22 16:12 38 ******************* 57 2025-06-22 16:13 39 ******************** 58 2025-06-22 16:14 38 ******************* 59 2025-06-22 16:15 38 ******************* SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/nda0 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.2-RELEASE amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/nda0 failed: INQUIRY failed