/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD1600BEVT-80A23T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Jan 15 17:19:33 2022 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5760) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 70) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 106 3 Spin_Up_Time POS--K 148 132 021 - 1600 4 Start_Stop_Count -O--CK 091 091 000 - 9005 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 098 098 000 - 2014 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1861 191 G-Sense_Error_Rate -O--CK 001 001 000 - 730 192 Power-Off_Retract_Count -O--CK 200 200 000 - 289 193 Load_Cycle_Count -O--CK 134 134 000 - 199935 194 Temperature_Celsius -O---K 110 096 000 - 33 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 2 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 89 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 89 [16] occurred at disk power-on lifetime: 1989 hours (82 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 08 3a b2 72 40 00 Error: UNC at LBA = 0x083ab272 = 138064498 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e8 00 00 08 3a b2 70 40 08 00:45:18.089 READ FPDMA QUEUED 60 00 b0 00 e0 00 00 06 ca 65 c0 40 08 00:45:18.089 READ FPDMA QUEUED 60 00 08 00 d8 00 00 05 c1 13 68 40 08 00:45:18.089 READ FPDMA QUEUED 60 02 00 00 d0 00 00 08 3a b4 40 40 08 00:45:18.089 READ FPDMA QUEUED 61 00 08 00 c0 00 00 03 84 1a 08 40 08 00:45:18.089 WRITE FPDMA QUEUED Error 88 [15] occurred at disk power-on lifetime: 1989 hours (82 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 08 3a b2 72 40 00 Error: UNC at LBA = 0x083ab272 = 138064498 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 08 3a b2 70 40 08 00:45:15.108 READ FPDMA QUEUED 60 00 08 00 a8 00 00 05 c1 13 68 40 08 00:45:15.108 READ FPDMA QUEUED 60 02 00 00 a0 00 00 08 3a b4 40 40 08 00:45:15.108 READ FPDMA QUEUED 60 00 90 00 98 00 00 06 ca 6b 10 40 08 00:45:15.108 READ FPDMA QUEUED 61 00 20 00 90 00 00 03 84 19 e8 40 08 00:45:15.108 WRITE FPDMA QUEUED Error 87 [14] occurred at disk power-on lifetime: 1989 hours (82 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 08 3a b2 72 40 00 Error: UNC at LBA = 0x083ab272 = 138064498 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 08 3a b2 70 40 08 00:45:12.136 READ FPDMA QUEUED 60 00 08 00 18 00 00 08 3a b2 68 40 08 00:45:12.136 READ FPDMA QUEUED 60 00 08 00 10 00 00 08 3a b2 60 40 08 00:45:12.136 READ FPDMA QUEUED 60 00 08 00 08 00 00 08 3a b2 58 40 08 00:45:12.136 READ FPDMA QUEUED 60 00 08 00 00 00 00 08 3a b2 50 40 08 00:45:12.136 READ FPDMA QUEUED Error 86 [13] occurred at disk power-on lifetime: 1989 hours (82 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 02 00 00 00 08 3a b2 72 40 00 Error: UNC at LBA = 0x083ab272 = 138064498 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 70 00 00 06 ca 61 70 40 08 00:45:09.102 READ FPDMA QUEUED 60 02 00 00 c0 00 00 08 3a b2 40 40 08 00:45:09.090 READ FPDMA QUEUED 60 02 00 00 b8 00 00 08 3a b0 40 40 08 00:45:09.089 READ FPDMA QUEUED 60 01 00 00 68 00 00 06 ca 64 c0 40 08 00:45:08.888 READ FPDMA QUEUED 60 02 00 00 b0 00 00 08 3a ae 40 40 08 00:45:08.871 READ FPDMA QUEUED Error 85 [12] occurred at disk power-on lifetime: 1989 hours (82 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 02 00 00 00 08 3a a4 e4 40 00 Error: UNC at LBA = 0x083aa4e4 = 138061028 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 88 00 b0 00 00 06 ca 67 f8 40 08 00:45:04.543 READ FPDMA QUEUED 60 02 00 00 a8 00 00 08 3a a4 40 40 08 00:45:04.529 READ FPDMA QUEUED 60 02 00 00 a0 00 00 08 3a a2 40 40 08 00:45:04.528 READ FPDMA QUEUED 60 00 20 00 98 00 00 06 ca 59 18 40 08 00:45:04.327 READ FPDMA QUEUED 60 02 00 00 90 00 00 08 3a a0 40 40 08 00:45:04.308 READ FPDMA QUEUED Error 84 [11] occurred at disk power-on lifetime: 1988 hours (82 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 08 3a a4 e4 40 00 Error: UNC at LBA = 0x083aa4e4 = 138061028 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e8 00 00 08 3a a4 e0 40 08 00:16:45.403 READ FPDMA QUEUED ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:16:45.403 SET FEATURES [Enable SATA feature] ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:16:45.402 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:16:45.402 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:16:45.401 IDENTIFY DEVICE Error 83 [10] occurred at disk power-on lifetime: 1988 hours (82 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 08 3a a4 e4 40 00 Error: UNC at LBA = 0x083aa4e4 = 138061028 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 f0 00 00 08 3a a4 e0 40 08 00:16:42.401 READ FPDMA QUEUED ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:16:42.401 SET FEATURES [Enable SATA feature] ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:16:42.401 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:16:42.401 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:16:42.400 IDENTIFY DEVICE Error 82 [9] occurred at disk power-on lifetime: 1988 hours (82 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 08 3a a4 e4 40 00 Error: UNC at LBA = 0x083aa4e4 = 138061028 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e8 00 00 08 3a a4 e0 40 08 00:16:39.421 READ FPDMA QUEUED b0 00 da 00 00 00 00 00 c2 4f 00 00 08 00:14:20.054 SMART RETURN STATUS b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 00:14:20.050 SMART READ DATA b0 00 d1 00 01 00 00 00 c2 4f 00 00 08 00:14:20.046 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] ec 00 00 00 01 00 00 00 00 00 00 00 08 00:14:20.045 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 2005 138061028 # 2 Short offline Completed: read failure 10% 2003 138061028 # 3 Short offline Completed: read failure 10% 1980 163491524 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 28/34 Celsius Lifetime Min/Max Temperature: ?/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (45) Index Estimated Time Temperature Celsius 46 2022-01-15 15:12 31 ************ ... ..( 7 skipped). .. ************ 54 2022-01-15 15:20 31 ************ 55 2022-01-15 15:21 32 ************* 56 2022-01-15 15:22 32 ************* 57 2022-01-15 15:23 32 ************* 58 2022-01-15 15:24 31 ************ ... ..( 4 skipped). .. ************ 63 2022-01-15 15:29 31 ************ 64 2022-01-15 15:30 30 *********** ... ..( 11 skipped). .. *********** 76 2022-01-15 15:42 30 *********** 77 2022-01-15 15:43 29 ********** 78 2022-01-15 15:44 29 ********** 79 2022-01-15 15:45 29 ********** 80 2022-01-15 15:46 30 *********** 81 2022-01-15 15:47 29 ********** ... ..( 6 skipped). .. ********** 88 2022-01-15 15:54 29 ********** 89 2022-01-15 15:55 28 ********* 90 2022-01-15 15:56 29 ********** 91 2022-01-15 15:57 29 ********** 92 2022-01-15 15:58 28 ********* 93 2022-01-15 15:59 29 ********** 94 2022-01-15 16:00 29 ********** 95 2022-01-15 16:01 28 ********* 96 2022-01-15 16:02 29 ********** 97 2022-01-15 16:03 28 ********* ... ..( 2 skipped). .. ********* 100 2022-01-15 16:06 28 ********* 101 2022-01-15 16:07 29 ********** 102 2022-01-15 16:08 28 ********* 103 2022-01-15 16:09 28 ********* 104 2022-01-15 16:10 29 ********** 105 2022-01-15 16:11 28 ********* ... ..( 10 skipped). .. ********* 116 2022-01-15 16:22 28 ********* 117 2022-01-15 16:23 29 ********** 118 2022-01-15 16:24 28 ********* 119 2022-01-15 16:25 28 ********* 120 2022-01-15 16:26 28 ********* 121 2022-01-15 16:27 29 ********** 122 2022-01-15 16:28 28 ********* ... ..( 2 skipped). .. ********* 125 2022-01-15 16:31 28 ********* 126 2022-01-15 16:32 29 ********** 127 2022-01-15 16:33 30 *********** ... ..( 8 skipped). .. *********** 8 2022-01-15 16:42 30 *********** 9 2022-01-15 16:43 31 ************ ... ..( 5 skipped). .. ************ 15 2022-01-15 16:49 31 ************ 16 2022-01-15 16:50 32 ************* 17 2022-01-15 16:51 31 ************ ... ..( 7 skipped). .. ************ 25 2022-01-15 16:59 31 ************ 26 2022-01-15 17:00 32 ************* ... ..( 2 skipped). .. ************* 29 2022-01-15 17:03 32 ************* 30 2022-01-15 17:04 33 ************** ... ..( 10 skipped). .. ************** 41 2022-01-15 17:15 33 ************** 42 2022-01-15 17:16 34 *************** 43 2022-01-15 17:17 34 *************** 44 2022-01-15 17:18 33 ************** 45 2022-01-15 17:19 34 *************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 42954 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 42954 R_ERR response for host-to-device non-data FIS 0x000a 2 21 Device-to-host register FISes sent due to a COMRESET 0x000b 2 6 CRC errors within host-to-device FIS 0x8000 4 18578 Vendor specific