/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.2 Device Model: ST980813AS Serial Number: -- Firmware Version: 3.ADB User Capacity: 80,026,361,856 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Fri Dec 31 03:58:07 2021 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Another SCT command is executing, abort Feature Control (SCT ext_status_code 0xffff, action_code=4, function_code=2) Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 426) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 84) minutes. SCT capabilities: (0x0035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 099 099 085 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1641 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 079 060 030 - 92899129 9 Power_On_Hours -O--CK 098 098 000 - 2241 10 Spin_Retry_Count PO--C- 100 100 034 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1598 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 072 047 045 - 28 (Min/Max 27/28) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 1292 193 Load_Cycle_Count -O---K 055 055 000 - 90158 194 Temperature_Celsius -O-RC- 028 053 000 - 28 (0 16 0 0 0) 195 Hardware_ECC_Recovered -O--C- 090 061 000 - 118324484 197 Current_Pending_Sector ----C- 100 100 000 - 0 198 Offline_Uncorrectable -OSRCK 100 100 000 - 0 199 UDMA_CRC_Error_Count ------ 200 200 000 - 18 200 Multi_Zone_Error_Rate -O--CK 100 253 000 - 0 202 Data_Address_Mark_Errs ------ 100 253 000 - 0 254 Free_Fall_Sensor ------ 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 SL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 SL R/O 1 NCQ Command Error log 0x11 SL R/O 1 SATA Phy Event Counters log 0x20 SL R/O 1 Streaming performance log [OBS-8] 0x21 SL R/O 1 Write stream error log 0x22 SL R/O 1 Read stream error log 0x23 SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f SL R/W 16 Host vendor specific log 0xa0 SL VS 1 Device vendor specific log 0xa1 SL VS 20 Device vendor specific log 0xa2 SL VS 101 Device vendor specific log 0xa8 SL VS 20 Device vendor specific log 0xa9 SL VS 1 Device vendor specific log 0xe0 SL R/W 1 SCT Command/Status 0xe1 SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 23 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 23 occurred at disk power-on lifetime: 2063 hours (85 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 fe 12 00 00 40 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 2f 00 01 10 00 00 40 00 02:40:43.998 READ LOG EXT 60 04 04 00 00 00 00 00 02:40:43.982 READ FPDMA QUEUED 60 08 08 00 00 00 00 00 02:40:43.975 READ FPDMA QUEUED 60 40 40 00 00 00 00 00 02:40:43.975 READ FPDMA QUEUED 60 11 11 00 00 00 00 00 02:40:43.964 READ FPDMA QUEUED Error 22 occurred at disk power-on lifetime: 2062 hours (85 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 fe 12 00 00 40 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 2f 00 01 10 00 00 40 00 02:23:52.203 READ LOG EXT 60 04 04 00 00 00 00 00 02:23:52.203 READ FPDMA QUEUED 60 18 18 00 00 00 00 00 02:23:52.153 READ FPDMA QUEUED 60 28 28 00 00 00 00 00 02:23:52.146 READ FPDMA QUEUED 60 08 08 00 00 00 00 00 02:23:52.145 READ FPDMA QUEUED Error 21 occurred at disk power-on lifetime: 1960 hours (81 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 fe 12 00 00 40 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 2f 00 01 10 00 00 40 00 00:17:11.461 READ LOG EXT 60 04 04 00 00 00 00 00 00:17:11.444 READ FPDMA QUEUED 60 80 80 00 00 00 00 00 00:17:11.443 READ FPDMA QUEUED 60 20 20 00 00 00 00 00 00:17:11.442 READ FPDMA QUEUED 60 80 80 00 00 00 00 00 00:17:11.418 READ FPDMA QUEUED Error 20 occurred at disk power-on lifetime: 1941 hours (80 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 fe 12 00 00 40 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 2f 00 01 10 00 00 40 00 00:16:53.949 READ LOG EXT 60 04 04 00 00 00 00 00 00:16:53.947 READ FPDMA QUEUED 60 80 80 00 00 00 00 00 00:16:53.946 READ FPDMA QUEUED 60 80 80 00 00 00 00 00 00:16:53.944 READ FPDMA QUEUED 60 80 80 00 00 00 00 00 00:16:53.943 READ FPDMA QUEUED Error 19 occurred at disk power-on lifetime: 1941 hours (80 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 fe 12 00 00 40 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 2f 00 01 10 00 00 40 00 00:16:53.949 READ LOG EXT 60 04 04 00 00 00 00 00 00:16:53.947 READ FPDMA QUEUED 60 80 80 00 00 00 00 00 00:16:53.946 READ FPDMA QUEUED 60 80 80 00 00 00 00 00 00:16:53.944 READ FPDMA QUEUED 60 80 80 00 00 00 00 00 00:16:53.943 READ FPDMA QUEUED SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 2207 - # 2 Short offline Completed without error 00% 2138 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 521 (0x0209) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 25/28 Celsius Lifetime Min/Max Temperature: 16/53 Celsius Specified Max Operating Temperature: 39 Celsius Under/Over Temperature Limit Count: 0/0 Another SCT command is executing, abort Read Data Table (SCT ext_status_code 0xffff, action_code=4, function_code=2) Read SCT Temperature History failed SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 8 Transition from drive PhyRdy to drive PhyNRdy 0x8002 2 0 Vendor specific 0x8003 2 4 Vendor specific 0x8004 2 0 Vendor specific