/dev/ada0
smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.2-RELEASE amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Blue
Device Model: WDC WD10EZEX-08WN4A0
Serial Number: --
LU WWN Device Id: 5 0014ee ...
Firmware Version: 01.01A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database 7.3/5528
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Mar 29 13:13:33 2025 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (11040) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 114) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 143 051 - 0
3 Spin_Up_Time POS--K 175 138 021 - 2216
4 Start_Stop_Count -O--CK 096 096 000 - 4444
5 Reallocated_Sector_Ct PO--CK 195 195 140 - 224
7 Seek_Error_Rate -OSR-K 200 199 000 - 0
9 Power_On_Hours -O--CK 076 076 000 - 17994
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 096 096 000 - 4342
192 Power-Off_Retract_Count -O--CK 200 200 000 - 124
193 Load_Cycle_Count -O--CK 199 199 000 - 4554
194 Temperature_Celsius -O---K 110 093 000 - 33
196 Reallocated_Event_Count -O--CK 178 178 000 - 22
197 Current_Pending_Sector -O--CK 200 200 000 - 2
198 Offline_Uncorrectable ----CK 200 200 000 - 2
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 6
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 48 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xdf GPL,SL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 13431 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13431 [14] occurred at disk power-on lifetime: 17596 hours (733 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 40 00 00 00 49 4b c7 e0 00
Error: UNC 64 sectors at LBA = 0x00494bc7 = 4803527
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 40 00 00 00 49 4b 9f e0 00 00:20:06.183 READ DMA EXT
25 00 00 00 08 00 00 00 e5 71 7f e0 00 00:20:06.165 READ DMA EXT
25 00 00 00 08 00 00 00 e6 3e 9f e0 00 00:20:06.156 READ DMA EXT
25 00 00 00 08 00 00 01 48 5d 1f e0 00 00:20:06.156 READ DMA EXT
25 00 00 00 08 00 00 01 48 5c 97 e0 00 00:20:06.142 READ DMA EXT
Error 13430 [13] occurred at disk power-on lifetime: 17596 hours (733 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 40 00 00 00 49 4b c7 e0 00
Error: UNC 64 sectors at LBA = 0x00494bc7 = 4803527
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 40 00 00 00 49 4b 9f e0 00 00:19:55.958 READ DMA EXT
25 00 00 00 40 00 00 00 20 d6 7f e0 00 00:19:55.958 READ DMA EXT
25 00 00 00 44 00 00 00 a5 00 bf e0 00 00:19:55.949 READ DMA EXT
25 00 00 00 05 00 00 00 98 8b c7 e0 00 00:19:55.940 READ DMA EXT
35 00 00 00 08 00 00 00 51 6e 5b e0 00 00:19:55.939 WRITE DMA EXT
Error 13429 [12] occurred at disk power-on lifetime: 17592 hours (733 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 01 00 00 00 00 49 4b c7 e0 00
Error: UNC 256 sectors at LBA = 0x00494bc7 = 4803527
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 01 00 00 00 00 49 4b 5f e0 00 00:43:26.266 READ DMA EXT
25 00 00 01 00 00 00 00 49 4a 5f e0 00 00:43:26.266 READ DMA EXT
25 00 00 01 00 00 00 00 49 49 5f e0 00 00:43:26.265 READ DMA EXT
25 00 00 01 00 00 00 00 49 48 5f e0 00 00:43:26.264 READ DMA EXT
25 00 00 01 00 00 00 00 49 47 5f e0 00 00:43:26.264 READ DMA EXT
Error 13428 [11] occurred at disk power-on lifetime: 17592 hours (733 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 01 00 00 00 00 49 4b c7 e0 00
Error: UNC 256 sectors at LBA = 0x00494bc7 = 4803527
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 01 00 00 00 00 49 4b 5f e0 00 00:42:10.817 READ DMA EXT
25 00 00 01 00 00 00 00 49 4a 5f e0 00 00:42:10.816 READ DMA EXT
25 00 00 01 00 00 00 00 49 49 5f e0 00 00:42:10.816 READ DMA EXT
25 00 00 01 00 00 00 00 49 48 5f e0 00 00:42:10.815 READ DMA EXT
25 00 00 01 00 00 00 00 49 47 5f e0 00 00:42:10.814 READ DMA EXT
Error 13427 [10] occurred at disk power-on lifetime: 17591 hours (732 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 40 00 00 00 49 4b c7 e0 00
Error: UNC 64 sectors at LBA = 0x00494bc7 = 4803527
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 40 00 00 00 49 4b 9f e0 00 00:27:35.830 READ DMA EXT
25 00 00 00 08 00 00 00 03 81 a7 e0 00 00:27:35.826 READ DMA EXT
25 00 00 00 40 00 00 02 6f 38 1f e0 00 00:27:35.821 READ DMA EXT
25 00 00 00 08 00 00 00 65 25 3f e0 00 00:27:35.811 READ DMA EXT
25 00 00 00 22 00 00 00 04 9e 0f e0 00 00:27:35.811 READ DMA EXT
Error 13426 [9] occurred at disk power-on lifetime: 17591 hours (732 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 40 00 00 00 49 4b c7 e0 00
Error: UNC 64 sectors at LBA = 0x00494bc7 = 4803527
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 40 00 00 00 49 4b 9f e0 00 00:27:21.179 READ DMA EXT
25 00 00 00 40 00 00 00 22 0d d7 e0 00 00:27:21.179 READ DMA EXT
25 00 00 00 40 00 00 00 49 4b 5f e0 00 00:27:21.179 READ DMA EXT
25 00 00 00 40 00 00 00 22 0d 97 e0 00 00:27:21.178 READ DMA EXT
25 00 00 00 40 00 00 00 49 4b 1f e0 00 00:27:21.178 READ DMA EXT
Error 13425 [8] occurred at disk power-on lifetime: 17577 hours (732 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 40 00 00 00 49 4b c7 e0 00
Error: UNC 64 sectors at LBA = 0x00494bc7 = 4803527
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 40 00 00 00 49 4b 9f e0 00 05:56:31.602 READ DMA EXT
25 00 00 00 08 00 00 00 49 4b 9f e0 00 05:56:31.525 READ DMA EXT
35 00 00 00 08 00 00 00 63 47 cf e0 00 05:56:31.482 WRITE DMA EXT
35 00 00 00 08 00 00 00 63 30 27 e0 00 05:56:31.482 WRITE DMA EXT
35 00 00 00 08 00 00 00 62 63 6f e0 00 05:56:31.481 WRITE DMA EXT
Error 13424 [7] occurred at disk power-on lifetime: 17577 hours (732 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 40 00 00 00 49 4b c7 e0 00
Error: UNC 64 sectors at LBA = 0x00494bc7 = 4803527
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 40 00 00 00 49 4b 9f e0 00 05:56:27.847 READ DMA EXT
ea 00 00 00 00 02 54 1f 00 00 00 e0 00 05:56:27.801 FLUSH CACHE EXT
35 00 00 00 08 00 00 00 02 54 17 e0 00 05:56:27.801 WRITE DMA EXT
35 00 00 00 08 00 00 00 61 05 47 e0 00 05:56:27.801 WRITE DMA EXT
35 00 00 00 08 00 00 00 00 00 d7 e0 00 05:56:27.801 WRITE DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
Device State: Active (0)
Current Temperature: 33 Celsius
Power Cycle Min/Max Temperature: 20/43 Celsius
Lifetime Min/Max Temperature: 4/50 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (442)
Index Estimated Time Temperature Celsius
443 2025-03-29 05:16 31 ************
... ..( 15 skipped). .. ************
459 2025-03-29 05:32 31 ************
460 2025-03-29 05:33 32 *************
... ..( 15 skipped). .. *************
476 2025-03-29 05:49 32 *************
477 2025-03-29 05:50 31 ************
... ..( 21 skipped). .. ************
21 2025-03-29 06:12 31 ************
22 2025-03-29 06:13 32 *************
... ..( 61 skipped). .. *************
84 2025-03-29 07:15 32 *************
85 2025-03-29 07:16 33 **************
... ..(112 skipped). .. **************
198 2025-03-29 09:09 33 **************
199 2025-03-29 09:10 32 *************
... ..( 60 skipped). .. *************
260 2025-03-29 10:11 32 *************
261 2025-03-29 10:12 33 **************
... ..( 24 skipped). .. **************
286 2025-03-29 10:37 33 **************
287 2025-03-29 10:38 31 ************
... ..( 45 skipped). .. ************
333 2025-03-29 11:24 31 ************
334 2025-03-29 11:25 32 *************
... ..( 98 skipped). .. *************
433 2025-03-29 13:04 32 *************
434 2025-03-29 13:05 31 ************
... ..( 7 skipped). .. ************
442 2025-03-29 13:13 31 ************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 1 Command failed due to ICRC error
0x0002 2 1 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 1 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x000b 2 1 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 1 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 1211960 Vendor specific