/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p7 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue (SATA) Device Model: WDC WD6400AAKS-22A7B2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.03B01 User Capacity: 640,135,028,736 bytes [640 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Mon Apr 3 06:54:39 2023 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11160) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 131) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 4 3 Spin_Up_Time POS--K 182 160 021 - 3866 4 Start_Stop_Count -O--CK 100 100 000 - 660 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 001 001 000 - 102955 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 657 192 Power-Off_Retract_Count -O--CK 200 200 000 - 178 193 Load_Cycle_Count -O--CK 200 200 000 - 660 194 Temperature_Celsius -O---K 116 085 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 2 198 Offline_Uncorrectable ----CK 200 200 000 - 2 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 134 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 134 [13] occurred at disk power-on lifetime: 29885 hours (1245 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 53 00 a6 17 40 00 Error: UNC at LBA = 0x125300a617 = 78701962775 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 00 00 00 12 a6 53 80 40 08 17:36:11.487 READ FPDMA QUEUED 60 00 40 00 f8 00 00 12 a6 53 00 40 08 17:36:11.487 READ FPDMA QUEUED 60 00 38 00 50 00 00 12 c5 05 80 40 08 17:36:11.362 READ FPDMA QUEUED 60 00 40 00 d0 00 00 12 c4 f9 80 40 08 17:36:11.356 READ FPDMA QUEUED 60 00 40 00 c8 00 00 12 a6 1d 80 40 08 17:36:11.356 READ FPDMA QUEUED Error 133 [12] occurred at disk power-on lifetime: 29640 hours (1235 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 43 00 a8 fa 40 00 Error: WP at LBA = 0x124300a8fa = 78433528058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 70 00 00 0f 9f 54 c8 40 08 16d+03:45:12.722 WRITE FPDMA QUEUED 61 00 10 00 d8 00 00 01 01 80 a0 40 08 16d+03:45:12.721 WRITE FPDMA QUEUED 61 00 08 00 60 00 00 0e 81 d6 f0 40 08 16d+03:45:12.721 WRITE FPDMA QUEUED 60 00 08 00 68 00 00 12 a8 43 f8 40 08 16d+03:45:12.720 READ FPDMA QUEUED 61 00 70 00 40 00 00 12 83 dd 10 40 08 16d+03:45:12.719 WRITE FPDMA QUEUED Error 132 [11] occurred at disk power-on lifetime: 29640 hours (1235 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 43 00 a8 fa 40 00 Error: UNC at LBA = 0x124300a8fa = 78433528058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 00 12 a8 43 f8 40 08 16d+03:45:10.047 READ FPDMA QUEUED 61 00 08 00 c0 00 00 0f 3e dc 48 40 08 16d+03:45:09.770 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 16d+03:45:09.515 FLUSH CACHE EXT 61 00 20 00 80 00 00 09 f1 37 60 40 08 16d+03:45:09.515 WRITE FPDMA QUEUED 61 00 20 00 78 00 00 01 00 b5 80 40 08 16d+03:45:09.515 WRITE FPDMA QUEUED Error 131 [10] occurred at disk power-on lifetime: 29640 hours (1235 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 43 00 a8 fa 40 00 Error: WP at LBA = 0x124300a8fa = 78433528058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 f8 00 00 12 83 d2 d0 40 08 16d+03:43:16.389 WRITE FPDMA QUEUED 60 00 08 00 f0 00 00 12 a8 43 f8 40 08 16d+03:43:16.389 READ FPDMA QUEUED 61 00 08 00 a8 00 00 0f 9f 54 c8 40 08 16d+03:43:16.389 WRITE FPDMA QUEUED 61 00 08 00 a0 00 00 0f 77 36 60 40 08 16d+03:43:16.389 WRITE FPDMA QUEUED 61 00 08 00 98 00 00 0f 95 be 98 40 08 16d+03:43:16.389 WRITE FPDMA QUEUED Error 130 [9] occurred at disk power-on lifetime: 29640 hours (1235 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 43 00 a8 fa 40 00 Error: UNC at LBA = 0x124300a8fa = 78433528058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e0 00 00 12 a8 43 f8 40 08 16d+03:43:13.735 READ FPDMA QUEUED 61 00 08 00 a0 00 00 0e 81 d6 f0 40 08 16d+03:43:13.661 WRITE FPDMA QUEUED 61 00 08 00 78 00 00 0f 3e dc 48 40 08 16d+03:43:12.127 WRITE FPDMA QUEUED 61 00 08 00 d8 00 00 12 83 d2 d0 40 08 16d+03:43:10.596 WRITE FPDMA QUEUED 61 00 08 00 90 00 00 0f 92 20 28 40 08 16d+03:43:10.337 WRITE FPDMA QUEUED Error 129 [8] occurred at disk power-on lifetime: 29640 hours (1235 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 43 00 a8 fa 40 00 Error: WP at LBA = 0x124300a8fa = 78433528058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 b8 00 00 12 9e bc 00 40 08 16d+03:41:24.603 WRITE FPDMA QUEUED 61 00 18 00 b0 00 00 12 bb de 80 40 08 16d+03:41:24.603 WRITE FPDMA QUEUED 61 00 58 00 80 00 00 12 83 db 48 40 08 16d+03:41:24.603 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 12 83 d2 d0 40 08 16d+03:41:24.601 WRITE FPDMA QUEUED 61 00 08 00 a8 00 00 12 9e bb c8 40 08 16d+03:41:24.601 WRITE FPDMA QUEUED Error 128 [7] occurred at disk power-on lifetime: 29640 hours (1235 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 43 00 a8 fa 40 00 Error: UNC at LBA = 0x124300a8fa = 78433528058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 12 a8 43 f8 40 08 16d+03:41:22.244 READ FPDMA QUEUED 60 00 08 00 30 00 00 12 9d 15 d0 40 08 16d+03:41:22.211 READ FPDMA QUEUED 60 00 30 00 28 00 00 12 b2 af 40 40 08 16d+03:41:22.170 READ FPDMA QUEUED 60 00 c0 00 20 00 00 12 b2 ae 80 40 08 16d+03:41:22.170 READ FPDMA QUEUED 60 01 00 00 f0 00 00 12 b2 ad 80 40 08 16d+03:41:22.169 READ FPDMA QUEUED Error 127 [6] occurred at disk power-on lifetime: 29640 hours (1235 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 12 43 00 a8 fa 40 00 Error: WP at LBA = 0x124300a8fa = 78433528058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 f8 00 00 0e 81 d6 f0 40 08 16d+03:41:00.785 WRITE FPDMA QUEUED 60 00 08 00 68 00 00 12 a8 43 f8 40 08 16d+03:41:00.785 READ FPDMA QUEUED 60 01 00 00 50 00 00 00 10 09 00 40 08 16d+03:41:00.785 READ FPDMA QUEUED 61 00 08 00 38 00 00 0f 3e dc 48 40 08 16d+03:41:00.785 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 16d+03:41:00.785 SET FEATURES [Enable SATA feature] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 35386 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 31/35 Celsius Lifetime Min/Max Temperature: 31/62 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (79) Index Estimated Time Temperature Celsius 80 2023-04-03 04:47 30 *********** ... ..( 36 skipped). .. *********** 117 2023-04-03 05:24 30 *********** 118 2023-04-03 05:25 ? - 119 2023-04-03 05:26 21 ** 120 2023-04-03 05:27 ? - 121 2023-04-03 05:28 26 ******* 122 2023-04-03 05:29 ? - 123 2023-04-03 05:30 27 ******** 124 2023-04-03 05:31 27 ******** 125 2023-04-03 05:32 28 ********* 126 2023-04-03 05:33 29 ********** 127 2023-04-03 05:34 29 ********** 0 2023-04-03 05:35 30 *********** 1 2023-04-03 05:36 ? - 2 2023-04-03 05:37 31 ************ 3 2023-04-03 05:38 31 ************ 4 2023-04-03 05:39 33 ************** ... ..( 7 skipped). .. ************** 12 2023-04-03 05:47 33 ************** 13 2023-04-03 05:48 34 *************** ... ..( 10 skipped). .. *************** 24 2023-04-03 05:59 34 *************** 25 2023-04-03 06:00 35 **************** ... ..( 15 skipped). .. **************** 41 2023-04-03 06:16 35 **************** 42 2023-04-03 06:17 34 *************** ... ..( 2 skipped). .. *************** 45 2023-04-03 06:20 34 *************** 46 2023-04-03 06:21 33 ************** 47 2023-04-03 06:22 33 ************** 48 2023-04-03 06:23 33 ************** 49 2023-04-03 06:24 32 ************* 50 2023-04-03 06:25 32 ************* 51 2023-04-03 06:26 31 ************ ... ..( 27 skipped). .. ************ 79 2023-04-03 06:54 31 ************ SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x8000 4 4732 Vendor specific