/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST500DM002-1ER14C Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC45 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Jan 9 19:08:20 2023 IST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 80) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 51) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 120 099 006 - 1211424 3 Spin_Up_Time PO---- 099 097 000 - 0 4 Start_Stop_Count -O--CK 098 098 020 - 2561 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 80 7 Seek_Error_Rate POSR-- 087 060 030 - 4948698153 9 Power_On_Hours -O--CK 078 078 000 - 19914 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1823 183 Runtime_Bad_Block -O--CK 065 065 000 - 35 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 045 045 000 - 55 188 Command_Timeout -O--CK 100 089 000 - 3 3 79 189 High_Fly_Writes -O-RCK 098 098 000 - 2 190 Airflow_Temperature_Cel -O---K 060 053 045 - 40 (Min/Max 30/40) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 917 193 Load_Cycle_Count -O--CK 093 093 000 - 15575 194 Temperature_Celsius -O---K 040 047 000 - 40 (0 21 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 023 000 - 20618 240 Head_Flying_Hours ------ 100 253 000 - 19595h+20m+23.889s 241 Total_LBAs_Written ------ 100 253 000 - 40151030590 242 Total_LBAs_Read ------ 100 253 000 - 631129779735 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 55 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 55 [14] occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 29 0a 32 98 00 00 Error: UNC at LBA = 0x290a3298 = 688534168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 0a 32 98 40 00 01:57:47.556 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:57:47.555 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:57:47.555 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:57:47.555 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:57:47.554 SET FEATURES [Set transfer mode] Error 54 [13] occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 29 0a 32 98 00 00 Error: UNC at LBA = 0x290a3298 = 688534168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 0a 32 98 40 00 01:57:43.925 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:57:43.925 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:57:43.925 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:57:43.924 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:57:43.924 SET FEATURES [Set transfer mode] Error 53 [12] occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 29 0a 32 98 00 00 Error: UNC at LBA = 0x290a3298 = 688534168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 0a 32 98 40 00 01:57:40.321 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:57:40.321 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:57:40.320 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:57:40.320 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:57:40.320 SET FEATURES [Set transfer mode] Error 52 [11] occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 29 0a 32 98 00 00 Error: UNC at LBA = 0x290a3298 = 688534168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 0a 32 98 40 00 01:57:36.649 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:57:36.648 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:57:36.648 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:57:36.648 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:57:36.648 SET FEATURES [Set transfer mode] Error 51 [10] occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 29 0a 32 98 00 00 Error: UNC at LBA = 0x290a3298 = 688534168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 0a 1c d8 40 00 01:57:32.963 READ FPDMA QUEUED 60 00 00 00 08 00 00 29 0a 1c d0 40 00 01:57:32.945 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:57:32.944 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:57:32.944 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:57:32.944 IDENTIFY DEVICE Error 50 [9] occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 29 0a 1c c8 00 00 Error: UNC at LBA = 0x290a1cc8 = 688528584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 0a 1c c8 40 00 01:57:29.272 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:57:29.272 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:57:29.272 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:57:29.271 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:57:29.271 SET FEATURES [Set transfer mode] Error 49 [8] occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 29 0a 1c c8 00 00 Error: UNC at LBA = 0x290a1cc8 = 688528584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 0a 1c c8 40 00 01:57:25.635 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:57:25.634 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:57:25.634 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:57:25.634 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:57:25.634 SET FEATURES [Set transfer mode] Error 48 [7] occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 29 0a 1c c8 00 00 Error: UNC at LBA = 0x290a1cc8 = 688528584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 0a 1c c8 40 00 01:57:21.938 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:57:21.937 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:57:21.937 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:57:21.937 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:57:21.936 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 19850 688513000 # 2 Short offline Completed: read failure 90% 19847 688513000 # 3 Conveyance offline Completed: read failure 90% 19825 688513000 # 4 Short offline Completed: read failure 90% 19825 688513000 # 5 Short offline Completed: read failure 90% 19825 688513000 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 30/39 Celsius Lifetime Min/Max Temperature: 21/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS