/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST31000524AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: JC4B User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed May 5 23:58:34 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 170) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 099 006 - 138904394 3 Spin_Up_Time PO---- 100 100 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3195 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 084 060 030 - 247913598 9 Power_On_Hours -O--CK 067 067 000 - 29407 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3194 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 080 080 000 - 20 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 068 058 045 - 32 (Min/Max 18/33) 194 Temperature_Celsius -O---K 032 042 000 - 32 (0 16 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 029 020 000 - 138904394 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 38256 (23 56 0) 241 Total_LBAs_Written ------ 100 253 000 - 4249333067 242 Total_LBAs_Read ------ 100 253 000 - 1326427888 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 20 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 20 [19] occurred at disk power-on lifetime: 7409 hours (308 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6c 9c a2 68 00 00 Error: UNC at LBA = 0x6c9ca268 = 1822204520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:19.625 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:19.543 READ LOG EXT 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:16.802 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:16.729 READ LOG EXT 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:13.980 READ FPDMA QUEUED Error 19 [18] occurred at disk power-on lifetime: 7409 hours (308 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6c 9c a2 68 00 00 Error: UNC at LBA = 0x6c9ca268 = 1822204520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:16.802 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:16.729 READ LOG EXT 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:13.980 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:13.898 READ LOG EXT 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:11.149 READ FPDMA QUEUED Error 18 [17] occurred at disk power-on lifetime: 7409 hours (308 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6c 9c a2 68 00 00 Error: UNC at LBA = 0x6c9ca268 = 1822204520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:13.980 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:13.898 READ LOG EXT 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:11.149 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:11.076 READ LOG EXT 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:08.364 READ FPDMA QUEUED Error 17 [16] occurred at disk power-on lifetime: 7409 hours (308 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6c 9c a2 68 00 00 Error: UNC at LBA = 0x6c9ca268 = 1822204520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:11.149 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:11.076 READ LOG EXT 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:08.364 READ FPDMA QUEUED 60 00 00 00 01 00 00 6c 9c a2 67 40 00 00:06:08.364 READ FPDMA QUEUED 60 00 00 00 01 00 00 6c 9c a2 66 40 00 00:06:08.364 READ FPDMA QUEUED Error 16 [15] occurred at disk power-on lifetime: 7409 hours (308 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6c 9c a2 68 00 00 Error: UNC at LBA = 0x6c9ca268 = 1822204520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 6c 9c a2 68 40 00 00:06:08.364 READ FPDMA QUEUED 60 00 00 00 01 00 00 6c 9c a2 67 40 00 00:06:08.364 READ FPDMA QUEUED 60 00 00 00 01 00 00 6c 9c a2 66 40 00 00:06:08.364 READ FPDMA QUEUED 60 00 00 00 01 00 00 6c 9c a2 65 40 00 00:06:08.363 READ FPDMA QUEUED 60 00 00 00 01 00 00 6c 9c a2 64 40 00 00:06:08.363 READ FPDMA QUEUED Error 15 [14] occurred at disk power-on lifetime: 7409 hours (308 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6c 9c a2 68 00 00 Error: UNC at LBA = 0x6c9ca268 = 1822204520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:06:05.442 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:05.414 READ LOG EXT 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:06:02.596 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:02.567 READ LOG EXT 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:05:59.827 READ FPDMA QUEUED Error 14 [13] occurred at disk power-on lifetime: 7409 hours (308 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6c 9c a2 68 00 00 Error: UNC at LBA = 0x6c9ca268 = 1822204520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:06:02.596 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:06:02.567 READ LOG EXT 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:05:59.827 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:05:59.753 READ LOG EXT 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:05:57.004 READ FPDMA QUEUED Error 13 [12] occurred at disk power-on lifetime: 7409 hours (308 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6c 9c a2 68 00 00 Error: UNC at LBA = 0x6c9ca268 = 1822204520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:05:59.827 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:05:59.753 READ LOG EXT 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:05:57.004 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:05:56.889 READ LOG EXT 60 00 00 00 40 00 00 6c 9c a2 62 40 00 00:05:54.190 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 26301 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 18/33 Celsius Lifetime Min/Max Temperature: 16/42 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (111) Index Estimated Time Temperature Celsius 112 2021-04-30 18:49 33 ************** ... ..( 2 skipped). .. ************** 115 2021-04-30 21:46 33 ************** 116 2021-04-30 22:45 34 *************** ... ..( 5 skipped). .. *************** 122 2021-05-01 04:39 34 *************** 123 2021-05-01 05:38 33 ************** ... ..( 2 skipped). .. ************** 126 2021-05-01 08:35 33 ************** 127 2021-05-01 09:34 ? - 0 2021-05-01 10:33 19 - 1 2021-05-01 11:32 19 - 2 2021-05-01 12:31 32 ************* 3 2021-05-01 13:30 33 ************** 4 2021-05-01 14:29 34 *************** 5 2021-05-01 15:28 34 *************** 6 2021-05-01 16:27 32 ************* 7 2021-05-01 17:26 33 ************** ... ..( 10 skipped). .. ************** 18 2021-05-02 04:15 33 ************** 19 2021-05-02 05:14 ? - 20 2021-05-02 06:13 19 - 21 2021-05-02 07:12 19 - 22 2021-05-02 08:11 31 ************ 23 2021-05-02 09:10 32 ************* 24 2021-05-02 10:09 33 ************** 25 2021-05-02 11:08 34 *************** 26 2021-05-02 12:07 33 ************** 27 2021-05-02 13:06 33 ************** 28 2021-05-02 14:05 34 *************** 29 2021-05-02 15:04 33 ************** ... ..( 6 skipped). .. ************** 36 2021-05-02 21:57 33 ************** 37 2021-05-02 22:56 ? - 38 2021-05-02 23:55 18 - 39 2021-05-03 00:54 18 - 40 2021-05-03 01:53 31 ************ 41 2021-05-03 02:52 32 ************* 42 2021-05-03 03:51 32 ************* 43 2021-05-03 04:50 33 ************** 44 2021-05-03 05:49 33 ************** 45 2021-05-03 06:48 32 ************* ... ..( 2 skipped). .. ************* 48 2021-05-03 09:45 32 ************* 49 2021-05-03 10:44 33 ************** 50 2021-05-03 11:43 33 ************** 51 2021-05-03 12:42 32 ************* 52 2021-05-03 13:41 ? - 53 2021-05-03 14:40 18 - 54 2021-05-03 15:39 18 - 55 2021-05-03 16:38 31 ************ 56 2021-05-03 17:37 33 ************** ... ..( 5 skipped). .. ************** 62 2021-05-03 23:31 33 ************** 63 2021-05-04 00:30 32 ************* 64 2021-05-04 01:29 32 ************* 65 2021-05-04 02:28 33 ************** 66 2021-05-04 03:27 ? - 67 2021-05-04 04:26 17 - 68 2021-05-04 05:25 17 - 69 2021-05-04 06:24 31 ************ 70 2021-05-04 07:23 32 ************* 71 2021-05-04 08:22 32 ************* 72 2021-05-04 09:21 32 ************* 73 2021-05-04 10:20 33 ************** 74 2021-05-04 11:19 33 ************** 75 2021-05-04 12:18 ? - 76 2021-05-04 13:17 18 - 77 2021-05-04 14:16 18 - 78 2021-05-04 15:15 31 ************ 79 2021-05-04 16:14 32 ************* 80 2021-05-04 17:13 33 ************** ... ..( 6 skipped). .. ************** 87 2021-05-05 00:06 33 ************** 88 2021-05-05 01:05 32 ************* 89 2021-05-05 02:04 32 ************* 90 2021-05-05 03:03 32 ************* 91 2021-05-05 04:02 33 ************** 92 2021-05-05 05:01 33 ************** 93 2021-05-05 06:00 ? - 94 2021-05-05 06:59 18 - 95 2021-05-05 07:58 18 - 96 2021-05-05 08:57 31 ************ 97 2021-05-05 09:56 32 ************* 98 2021-05-05 10:55 33 ************** ... ..( 2 skipped). .. ************** 101 2021-05-05 13:52 33 ************** 102 2021-05-05 14:51 32 ************* 103 2021-05-05 15:50 33 ************** ... ..( 2 skipped). .. ************** 106 2021-05-05 18:47 33 ************** 107 2021-05-05 19:46 32 ************* 108 2021-05-05 20:45 32 ************* 109 2021-05-05 21:44 32 ************* 110 2021-05-05 22:43 33 ************** 111 2021-05-05 23:42 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/ada1 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3250620AS Serial Number: -- Firmware Version: 3.AAJ User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Wed May 5 23:58:34 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 92) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 119 087 006 - 0 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3522 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 2 7 Seek_Error_Rate POSR-- 087 060 030 - 488066449 9 Power_On_Hours -O--CK 071 071 000 - 25961 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 095 095 020 - 5449 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 058 049 045 - 42 (Min/Max 20/42) 194 Temperature_Celsius -O---K 042 051 000 - 42 (0 18 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 068 055 000 - 112981217 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS