/dev/ada0 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.3-RELEASE-p2 amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron RealSSD C300/P300 Device Model: C300-CTFDDAC128MAG Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: 0007 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.5/5706 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 8 18:54:05 2025 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 595) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 9) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 709 5 Reallocated_Sector_Ct PO--CK 100 100 000 - 32768 9 Power_On_Hours -O--CK 100 100 000 - 68101 12 Power_Cycle_Count -O--CK 100 100 000 - 4343 170 Grown_Failing_Block_Ct PO--CK 100 100 000 - 16 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Wear_Leveling_Count PO--CK 090 090 000 - 502 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 2 181 Non4k_Aligned_Access -O---K 100 100 000 - 5720 4024 1696 183 SATA_Iface_Downshift -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 709 188 Command_Timeout -O--CK 100 100 000 - 0 189 Factory_Bad_Block_Ct -OSR-- 100 100 000 - 169 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 100 100 000 - 16 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 202 Percent_Lifetime_Used ---RC- 090 090 000 - 10 206 Write_Error_Rate -OSR-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 16383 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 3449 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 1741 Device vendor specific log 0xa0 SL VS 205 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (16383 sectors) No Errors Logged SMART Extended Self-test Log size 3449 not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: ? Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: -5/75 Celsius Temperature History Size (Index): 478 (341) Index Estimated Time Temperature Celsius 342 2025-09-05 11:20 ? - ... ..(476 skipped). .. - 341 2025-09-08 18:50 ? - SCT Error Recovery Control: Read: 40 (4.0 seconds) Write: 40 (4.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 4343 --- Lifetime Power-On Resets 0x01 0x010 4 68101 --- Power-on Hours 0x01 0x018 6 50045992560 --- Logical Sectors Written 0x01 0x020 6 1754266556 --- Number of Write Commands 0x01 0x028 6 36725520144 --- Logical Sectors Read 0x01 0x030 6 732470988 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 709 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 -128 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 - --- Highest Temperature 0x05 0x028 1 - --- Lowest Temperature 0x05 0x030 1 - --- Highest Average Short Term Temperature 0x05 0x038 1 - --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 - --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 - --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 17542 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 5 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 5 Device-to-host register FISes sent due to a COMRESET /dev/ada1 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.3-RELEASE-p2 amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST2000DM001-1ER164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC25 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.5/5706 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 8 18:54:06 2025 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 80) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 217) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 110 095 006 - 26327736 3 Spin_Up_Time PO---- 097 096 000 - 0 4 Start_Stop_Count -O--CK 095 095 020 - 5800 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 424 7 Seek_Error_Rate POSR-- 085 060 030 - 384067768 9 Power_On_Hours -O--CK 032 032 000 - 60284 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3914 183 Runtime_Bad_Block -O--CK 079 079 000 - 21 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 659 188 Command_Timeout -O--CK 100 097 000 - 9 15 18 189 High_Fly_Writes -O-RCK 093 093 000 - 7 190 Airflow_Temperature_Cel -O---K 062 050 045 - 38 (Min/Max 36/39) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 582 193 Load_Cycle_Count -O--CK 096 096 000 - 9125 194 Temperature_Celsius -O---K 038 050 000 - 38 (0 14 0 0 0) 197 Current_Pending_Sector -O--C- 100 099 000 - 0 198 Offline_Uncorrectable ----C- 100 099 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 194 000 - 59 240 Head_Flying_Hours ------ 100 253 000 - 43138h+02m+43.594s 241 Total_LBAs_Written ------ 100 253 000 - 69126352332 242 Total_LBAs_Read ------ 100 253 000 - 370207408477 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 665 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 665 [4] occurred at disk power-on lifetime: 59334 hours (2472 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 a2 c0 56 98 00 00 Error: UNC at LBA = 0xa2c05698 = 2730514072 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 a2 c0 4b 50 40 00 01:11:43.885 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 4a 50 40 00 01:11:43.885 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 49 50 40 00 01:11:43.885 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 48 50 40 00 01:11:43.885 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 47 50 40 00 01:11:43.885 READ FPDMA QUEUED Error 664 [3] occurred at disk power-on lifetime: 59334 hours (2472 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 a2 c0 4c b0 00 00 Error: UNC at LBA = 0xa2c04cb0 = 2730511536 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 a2 c0 4b 50 40 00 01:11:40.208 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 4a 50 40 00 01:11:40.208 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 49 50 40 00 01:11:40.208 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 48 50 40 00 01:11:40.208 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 47 50 40 00 01:11:40.208 READ FPDMA QUEUED Error 663 [2] occurred at disk power-on lifetime: 59334 hours (2472 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 a2 c0 45 58 00 00 Error: UNC at LBA = 0xa2c04558 = 2730509656 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 a2 c0 63 50 40 00 01:11:36.731 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 62 50 40 00 01:11:36.731 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 61 50 40 00 01:11:36.731 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 60 50 40 00 01:11:36.731 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 5f 50 40 00 01:11:36.731 READ FPDMA QUEUED Error 662 [1] occurred at disk power-on lifetime: 59334 hours (2472 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 a2 be 88 48 00 00 Error: UNC at LBA = 0xa2be8848 = 2730395720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 a2 be 89 50 40 00 01:11:29.251 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 88 50 40 00 01:11:29.251 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 2a 50 40 00 01:11:29.126 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 29 50 40 00 01:11:29.126 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 28 50 40 00 01:11:29.124 READ FPDMA QUEUED Error 661 [0] occurred at disk power-on lifetime: 59334 hours (2472 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 a2 be 88 48 00 00 Error: UNC at LBA = 0xa2be8848 = 2730395720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 a2 be 89 50 40 00 01:11:18.124 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 88 50 40 00 01:11:18.124 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 2a 50 40 00 01:11:17.927 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 29 50 40 00 01:11:17.739 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 28 50 40 00 01:11:17.739 READ FPDMA QUEUED Error 660 [19] occurred at disk power-on lifetime: 59333 hours (2472 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 a2 be 88 48 00 00 Error: UNC at LBA = 0xa2be8848 = 2730395720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 a2 be 89 50 40 00 00:11:43.919 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 88 50 40 00 00:11:43.919 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 2a 50 40 00 00:11:43.488 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 29 50 40 00 00:11:43.488 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 be 28 50 40 00 00:11:43.486 READ FPDMA QUEUED Error 659 [18] occurred at disk power-on lifetime: 59162 hours (2465 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 a2 c0 6a 27 00 00 Error: UNC at LBA = 0xa2c06a27 = 2730519079 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 a2 c0 6a 27 40 00 02:08:24.476 READ FPDMA QUEUED ef 00 82 00 00 00 00 00 00 00 00 a0 00 02:08:24.445 SET FEATURES [Disable write cache] 60 00 00 01 00 00 00 a2 c0 71 27 40 00 02:08:24.442 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 70 27 40 00 02:08:24.442 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 6f 27 40 00 02:08:24.442 READ FPDMA QUEUED Error 658 [17] occurred at disk power-on lifetime: 59162 hours (2465 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 a2 c0 6a 27 00 00 Error: UNC at LBA = 0xa2c06a27 = 2730519079 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 a2 c0 71 27 40 00 02:08:24.237 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 70 27 40 00 02:08:24.237 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 6f 27 40 00 02:08:24.237 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 6e 27 40 00 02:08:24.237 READ FPDMA QUEUED 60 00 00 01 00 00 00 a2 c0 6d 27 40 00 02:08:24.237 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 00% 39332 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 35/38 Celsius Lifetime Min/Max Temperature: 14/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/ada2 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.3-RELEASE-p2 amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red (CMR) Device Model: WDC WD20EFRX-68EUZN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 1,000,227,396,608 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.5/5706 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 8 18:54:06 2025 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26160) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 265) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 179 172 021 - 4033 4 Start_Stop_Count -O--CK 099 099 000 - 1626 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 002 002 000 - 72177 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 918 192 Power-Off_Retract_Count -O--CK 200 200 000 - 408 193 Load_Cycle_Count -O--CK 196 196 000 - 13250 194 Temperature_Celsius -O---K 111 086 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 191 000 - 83 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 52103 hours (2170 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 01 10 40 00 Error: UNC at LBA = 0x00000110 = 272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 00 00 00 40 00 00:00:41.165 READ FPDMA QUEUED 60 00 00 00 00 00 00 00 00 00 00 40 00 00:00:41.165 READ FPDMA QUEUED f5 00 00 00 00 00 00 00 00 00 00 00 08 00:00:40.813 SECURITY FREEZE LOCK ec 00 00 00 00 00 00 00 00 00 00 00 08 00:00:40.813 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 00 08 00:00:40.813 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3582 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 32/36 Celsius Lifetime Min/Max Temperature: 19/61 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (155) Index Estimated Time Temperature Celsius 156 2025-09-08 10:57 33 ************** ... ..( 19 skipped). .. ************** 176 2025-09-08 11:17 33 ************** 177 2025-09-08 11:18 32 ************* ... ..( 82 skipped). .. ************* 260 2025-09-08 12:41 32 ************* 261 2025-09-08 12:42 31 ************ ... ..( 22 skipped). .. ************ 284 2025-09-08 13:05 31 ************ 285 2025-09-08 13:06 ? - 286 2025-09-08 13:07 31 ************ 287 2025-09-08 13:08 ? - 288 2025-09-08 13:09 32 ************* 289 2025-09-08 13:10 32 ************* 290 2025-09-08 13:11 32 ************* 291 2025-09-08 13:12 33 ************** 292 2025-09-08 13:13 33 ************** 293 2025-09-08 13:14 33 ************** 294 2025-09-08 13:15 34 *************** ... ..( 4 skipped). .. *************** 299 2025-09-08 13:20 34 *************** 300 2025-09-08 13:21 35 **************** ... ..( 7 skipped). .. **************** 308 2025-09-08 13:29 35 **************** 309 2025-09-08 13:30 36 ***************** 310 2025-09-08 13:31 32 ************* ... ..( 73 skipped). .. ************* 384 2025-09-08 14:45 32 ************* 385 2025-09-08 14:46 33 ************** ... ..( 72 skipped). .. ************** 458 2025-09-08 15:59 33 ************** 459 2025-09-08 16:00 ? - 460 2025-09-08 16:01 33 ************** 461 2025-09-08 16:02 33 ************** 462 2025-09-08 16:03 34 *************** 463 2025-09-08 16:04 34 *************** 464 2025-09-08 16:05 34 *************** 465 2025-09-08 16:06 35 **************** ... ..( 6 skipped). .. **************** 472 2025-09-08 16:13 35 **************** 473 2025-09-08 16:14 36 ***************** ... ..( 8 skipped). .. ***************** 4 2025-09-08 16:23 36 ***************** 5 2025-09-08 16:24 37 ****************** 6 2025-09-08 16:25 37 ****************** 7 2025-09-08 16:26 36 ***************** 8 2025-09-08 16:27 ? - 9 2025-09-08 16:28 36 ***************** 10 2025-09-08 16:29 37 ****************** ... ..( 30 skipped). .. ****************** 41 2025-09-08 17:00 37 ****************** 42 2025-09-08 17:01 36 ***************** ... ..( 9 skipped). .. ***************** 52 2025-09-08 17:11 36 ***************** 53 2025-09-08 17:12 35 **************** ... ..( 10 skipped). .. **************** 64 2025-09-08 17:23 35 **************** 65 2025-09-08 17:24 34 *************** ... ..( 26 skipped). .. *************** 92 2025-09-08 17:51 34 *************** 93 2025-09-08 17:52 ? - 94 2025-09-08 17:53 34 *************** 95 2025-09-08 17:54 34 *************** 96 2025-09-08 17:55 35 **************** ... ..( 2 skipped). .. **************** 99 2025-09-08 17:58 35 **************** 100 2025-09-08 17:59 36 ***************** ... ..( 16 skipped). .. ***************** 117 2025-09-08 18:16 36 ***************** 118 2025-09-08 18:17 37 ****************** 119 2025-09-08 18:18 37 ****************** 120 2025-09-08 18:19 37 ****************** 121 2025-09-08 18:20 36 ***************** ... ..( 4 skipped). .. ***************** 126 2025-09-08 18:25 36 ***************** 127 2025-09-08 18:26 35 **************** ... ..( 4 skipped). .. **************** 132 2025-09-08 18:31 35 **************** 133 2025-09-08 18:32 34 *************** ... ..( 9 skipped). .. *************** 143 2025-09-08 18:42 34 *************** 144 2025-09-08 18:43 33 ************** ... ..( 10 skipped). .. ************** 155 2025-09-08 18:54 33 ************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1344 Vendor specific /dev/ada3 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.3-RELEASE-p2 amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue / Red / Green SSDs Device Model: WD Blue SA510 2.5 1000GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: 52046100 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.5/5706 ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 8 18:54:06 2025 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 154 12 Power_Cycle_Count -O--CK 100 100 000 - 283 165 Block_Erase_Count -O--CK 100 100 000 - 880497721780 166 Minimum_PE_Cycles_TLC -O--CK 100 100 000 - 7 167 Max_Bad_Blocks_per_Die -O--CK 100 100 000 - 109 168 Maximum_PE_Cycles_TLC -O--CK 100 100 000 - 13 169 Total_Bad_Blocks -O--CK 100 100 000 - 356 170 Grown_Bad_Blocks -O--CK 100 100 000 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 005 - 9 174 Unexpected_Power_Loss -O--CK 100 100 000 - 4 184 End-to-End_Error -O--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 014 - 33 (Min/Max 19/48) 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x003a003c003a 232 Available_Reservd_Space PO--CK 100 100 004 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 000 - 7542 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 6018 241 Host_Writes_GiB ----CK 253 253 000 - 7786 242 Host_Reads_GiB ----CK 253 253 000 - 7262 244 Temp_Throttle_Status -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa7 GPL,SL VS 1 Device vendor specific log 0xde GPL,SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (empty) == 0x05 ===== = = === == Temperature Statistics (empty) == 0x07 ===== = = === == Solid State Device Statistics (empty) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/nda0 smartctl 7.5 2025-04-30 r5714 [FreeBSD 14.3-RELEASE-p2 amd64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/nda0 failed: INQUIRY failed