/dev/sd1 smartctl 7.3 2022-02-28 r5338 [NetBSD 10.0 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: USB Product: SanDisk 3.2Gen1 Revision: 1.00 Compliance: SPC-4 User Capacity: 61,524,148,224 bytes [61.5 GB] Logical block size: 512 bytes Serial number: -- Device type: disk Local Time is: Thu Apr 4 05:48:21 2024 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 0 C Drive Trip Temperature: 0 C Error Counter logging not supported Device does not support Self Test logging /dev/wd0 smartctl 7.3 2022-02-28 r5338 [NetBSD 10.0 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SanDisk SSD i110 16GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: i221000 User Capacity: 16,013,942,784 bytes [16.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 1.8 inches TRIM Command: Available, deterministic Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 4 05:48:21 2024 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 3) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 5 Reallocated_Sector_Ct 0x0002 100 100 000 Old_age Always - 0 9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 3463 12 Power_Cycle_Count 0x0002 100 100 000 Old_age Always - 1351 165 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 510902 171 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 0 172 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 0 173 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 255 174 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 155 187 Reported_Uncorrect 0x0002 100 100 000 Old_age Always - 0 194 Temperature_Celsius 0x0022 044 056 000 Old_age Always - 56 (Min/Max 16/63) 230 Unknown_SSD_Attribute 0x0002 100 100 000 Old_age Always - 850 232 Available_Reservd_Space 0x0003 100 100 005 Pre-fail Always - 0 234 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 750 241 Total_LBAs_Written 0x0002 100 100 000 Old_age Always - 4328501917 242 Total_LBAs_Read 0x0002 100 100 000 Old_age Always - 9418323638 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.