/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.1-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SAMSUNG SP0411N Serial Number: -- Firmware Version: TW100-11 User Capacity: 40,059,321,856 bytes [40.0 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA/ATAPI-7 T13/1532D revision 0 Local Time is: Sat Apr 17 14:24:02 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 900) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 15) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 051 - 40 3 Spin_Up_Time POS--- 074 057 000 - 4736 4 Start_Stop_Count -O--CK 096 096 000 - 4210 5 Reallocated_Sector_Ct PO--CK 253 253 010 - 0 7 Seek_Error_Rate PO-R-- 253 253 051 - 0 8 Seek_Time_Performance --S--K 253 253 000 - 0 9 Power_On_Hours -O--CK 098 098 000 - 1459740 10 Spin_Retry_Count PO--C- 253 253 049 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2223 194 Temperature_Celsius -O---K 127 058 000 - 37 195 Hardware_ECC_Recovered -O-R-- 100 100 000 - 100878490 196 Reallocated_Event_Count -O--C- 099 099 000 - 4 197 Current_Pending_Sector PO--CK 253 253 010 - 0 198 Offline_Uncorrectable P---CK 099 099 010 - 4 199 UDMA_CRC_Error_Count PO-R-- 100 100 051 - 76 200 Multi_Zone_Error_Rate PO-R-- 100 100 051 - 0 201 Soft_Read_Error_Rate PO-R-- 100 100 051 - 3 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x06 SL R/O 2 SMART self-test log 0x80-0x9f SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 Warning: ATA error count 37632 inconsistent with error log pointer 5 ATA Error Count: 37632 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37632 occurred at disk power-on lifetime: 12069 hours (502 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 01 51 40 00 58 53 f1 Error: AMNF 64 sectors at LBA = 0x01535800 = 22239232 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 40 00 58 53 f1 00 20d+23:36:49.938 READ DMA ca 00 08 c0 00 00 f0 00 20d+23:36:43.938 WRITE DMA ca 00 40 c0 ae 47 f2 00 20d+23:36:43.938 WRITE DMA ca 00 08 40 00 9e f0 00 20d+23:36:43.938 WRITE DMA c8 00 08 88 12 c3 f4 00 20d+23:36:43.438 READ DMA Error 37631 occurred at disk power-on lifetime: 10748 hours (447 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 e8 05 88 f0 Error: ICRC, ABRT at LBA = 0x008805e8 = 8914408 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 e8 05 88 f0 00 00:17:40.313 READ DMA c8 00 00 e8 05 87 f0 00 00:17:40.313 READ DMA c8 00 00 e8 05 86 f0 00 00:17:40.313 READ DMA c8 00 00 e8 05 85 f0 00 00:17:40.313 READ DMA c8 00 00 e8 05 84 f0 00 00:17:40.313 READ DMA Error 37630 occurred at disk power-on lifetime: 9893 hours (412 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 01 00 00 b0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b1 10 01 01 00 00 b0 00 00:12:06.000 DEVICE CONFIGURATION [Reserved subcommand] [OBS-ACS-3] Error 37629 occurred at disk power-on lifetime: 9893 hours (412 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 01 00 00 b0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b1 10 01 01 00 00 b0 00 00:11:28.938 DEVICE CONFIGURATION [Reserved subcommand] [OBS-ACS-3] Error 37628 occurred at disk power-on lifetime: 9893 hours (412 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 01 00 00 b0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b1 10 01 01 00 00 b0 00 00:06:12.000 DEVICE CONFIGURATION [Reserved subcommand] [OBS-ACS-3] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 11545 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/ada1 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.1-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST500DM002-1BD142 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: KC45 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Apr 17 14:24:03 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 81) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 108 072 006 - 19684464 3 Spin_Up_Time PO---- 100 097 000 - 0 4 Start_Stop_Count -O--CK 037 037 020 - 65535 5 Reallocated_Sector_Ct PO--CK 095 095 036 - 1648 7 Seek_Error_Rate POSR-- 071 060 030 - 103435131439 9 Power_On_Hours -O--CK 083 083 000 - 15113 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 5027 183 Runtime_Bad_Block -O--CK 096 096 000 - 4 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 2508 188 Command_Timeout -O--CK 100 081 000 - 4 4 155 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 062 044 045 Past 38 (Min/Max 36/41 #49) 194 Temperature_Celsius -O---K 038 056 000 - 38 (0 17 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 026 020 000 - 19684464 197 Current_Pending_Sector -O--C- 100 030 000 - 0 198 Offline_Uncorrectable ----C- 100 030 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 177 000 - 995 240 Head_Flying_Hours ------ 100 253 000 - 15085h+40m+33.395s 241 Total_LBAs_Written ------ 100 253 000 - 723767495 242 Total_LBAs_Read ------ 100 253 000 - 1405066294 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 2534 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2534 [13] occurred at disk power-on lifetime: 10941 hours (455 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 a3 19 98 00 00 Error: WP at LBA = 0x00a31998 = 10688920 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 06 0a 7f f0 40 00 03:07:50.981 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 15 0d 84 38 40 00 03:07:50.981 READ FPDMA QUEUED 61 00 00 00 08 00 00 06 0a 7f c0 40 00 03:07:50.980 WRITE FPDMA QUEUED 61 00 00 00 d0 00 00 1c 94 22 58 40 00 03:07:50.979 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 17 ce 4b d0 40 00 03:07:50.979 READ FPDMA QUEUED Error 2533 [12] occurred at disk power-on lifetime: 10941 hours (455 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 a3 19 98 00 00 Error: WP at LBA = 0x00a31998 = 10688920 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 10 00 00 06 21 79 70 40 00 03:07:47.125 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 00 a3 19 98 40 00 03:07:47.124 READ FPDMA QUEUED 61 00 00 00 08 00 00 1c 94 22 50 40 00 03:07:47.124 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 03:07:47.051 FLUSH CACHE EXT 61 00 00 00 10 00 00 06 21 78 b0 40 00 03:07:47.025 WRITE FPDMA QUEUED Error 2532 [11] occurred at disk power-on lifetime: 10941 hours (455 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 a3 19 98 00 00 Error: WP at LBA = 0x00a31998 = 10688920 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 05 78 00 00 06 2a 61 60 40 00 03:07:43.096 WRITE FPDMA QUEUED 61 00 00 00 b8 00 00 06 21 a1 e0 40 00 03:07:43.095 WRITE FPDMA QUEUED 61 00 00 02 f8 00 00 06 29 9f 78 40 00 03:07:43.093 WRITE FPDMA QUEUED 61 00 00 00 90 00 00 06 21 9c 38 40 00 03:07:43.093 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 06 21 77 50 40 00 03:07:43.092 WRITE FPDMA QUEUED Error 2531 [10] occurred at disk power-on lifetime: 10941 hours (455 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 a3 19 98 00 00 Error: UNC at LBA = 0x00a31998 = 10688920 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 a3 19 98 40 00 03:07:39.371 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 a3 19 90 40 00 03:07:39.371 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 a3 19 88 40 00 03:07:39.370 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 a3 19 80 40 00 03:07:39.370 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 a3 19 78 40 00 03:07:39.370 READ FPDMA QUEUED Error 2530 [9] occurred at disk power-on lifetime: 10941 hours (455 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 a3 19 98 00 00 Error: UNC at LBA = 0x00a31998 = 10688920 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 e0 00 00 1c 14 2f 20 40 00 03:07:35.444 READ FPDMA QUEUED 60 00 00 04 00 00 00 00 a3 18 c0 40 00 03:07:35.418 READ FPDMA QUEUED 60 00 00 04 00 00 00 1c 14 2b 20 40 00 03:07:34.990 READ FPDMA QUEUED 60 00 00 04 00 00 00 1c 14 27 20 40 00 03:07:34.426 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 03:07:34.276 FLUSH CACHE EXT Error 2529 [8] occurred at disk power-on lifetime: 10822 hours (450 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 b2 be 28 00 00 Error: WP at LBA = 0x00b2be28 = 11714088 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 10 00 00 00 0b 81 30 40 00 02:18:55.040 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 0b 81 08 40 00 02:18:55.040 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 0b 80 f0 40 00 02:18:55.040 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 0b 80 a8 40 00 02:18:55.039 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 00 0b 80 80 40 00 02:18:55.039 WRITE FPDMA QUEUED Error 2528 [7] occurred at disk power-on lifetime: 10822 hours (450 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 b2 be 28 00 00 Error: WP at LBA = 0x00b2be28 = 11714088 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 2d 14 2f f8 40 00 02:18:51.249 WRITE FPDMA QUEUED 61 00 00 00 30 00 00 2d 14 5e e0 40 00 02:18:51.248 WRITE FPDMA QUEUED 61 00 00 00 70 00 00 1c 92 78 40 40 00 02:18:51.243 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 2d 14 5e c0 40 00 02:18:51.243 WRITE FPDMA QUEUED 60 00 00 00 18 00 00 23 2c ab 00 40 00 02:18:51.199 READ FPDMA QUEUED Error 2527 [6] occurred at disk power-on lifetime: 10822 hours (450 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 b2 be 28 00 00 Error: UNC at LBA = 0x00b2be28 = 11714088 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 9d 08 c0 40 00 02:18:47.423 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 df 01 a0 40 00 02:18:47.423 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 9d 08 b8 40 00 02:18:47.422 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 df 01 98 40 00 02:18:47.422 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 9d 08 b0 40 00 02:18:47.421 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 14454 - # 2 Short offline Completed without error 00% 10586 - # 3 Short offline Completed without error 00% 10572 - # 4 Short offline Completed without error 00% 10558 - # 5 Short offline Completed without error 00% 10546 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 36/41 Celsius Lifetime Min/Max Temperature: 17/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (114) Index Estimated Time Temperature Celsius 115 2021-04-12 09:16 38 ******************* ... ..( 3 skipped). .. ******************* 119 2021-04-12 13:12 38 ******************* 120 2021-04-12 14:11 37 ****************** 121 2021-04-12 15:10 37 ****************** 122 2021-04-12 16:09 38 ******************* ... ..( 20 skipped). .. ******************* 15 2021-04-13 12:48 38 ******************* 16 2021-04-13 13:47 39 ******************** ... ..( 8 skipped). .. ******************** 25 2021-04-13 22:38 39 ******************** 26 2021-04-13 23:37 38 ******************* 27 2021-04-14 00:36 38 ******************* 28 2021-04-14 01:35 39 ******************** ... ..( 3 skipped). .. ******************** 32 2021-04-14 05:31 39 ******************** 33 2021-04-14 06:30 38 ******************* ... ..( 6 skipped). .. ******************* 40 2021-04-14 13:23 38 ******************* 41 2021-04-14 14:22 39 ******************** ... ..( 39 skipped). .. ******************** 81 2021-04-16 05:42 39 ******************** 82 2021-04-16 06:41 38 ******************* 83 2021-04-16 07:40 38 ******************* 84 2021-04-16 08:39 38 ******************* 85 2021-04-16 09:38 39 ******************** 86 2021-04-16 10:37 38 ******************* 87 2021-04-16 11:36 39 ******************** 88 2021-04-16 12:35 38 ******************* 89 2021-04-16 13:34 39 ******************** 90 2021-04-16 14:33 38 ******************* ... ..( 16 skipped). .. ******************* 107 2021-04-17 07:16 38 ******************* 108 2021-04-17 08:15 39 ******************** 109 2021-04-17 09:14 39 ******************** 110 2021-04-17 10:13 38 ******************* 111 2021-04-17 11:12 38 ******************* 112 2021-04-17 12:11 36 ***************** 113 2021-04-17 13:10 38 ******************* 114 2021-04-17 14:09 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 14 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS