/dev/da0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.0-STABLE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SAMSUNG Product: MZILT960HBHQ/007 Revision: GXA0 Compliance: SPC-5 User Capacity: 960,197,124,096 bytes [960 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5002538b71832fe0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Apr 28 19:16:32 2022 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 0% Current temperature = 33 Lifetime maximum temperature = 43 Lifetime minimum temperature = 24 Maximum temperature since power on = 33 Minimum temperature since power on = 31 Manufactured in week 34 of year 2021 Accumulated start-stop cycles: 20 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 2.037 0 write: 0 0 0 0 0 5339.937 0 Non-medium error count: 134 Pending defect count:0 Pending Defects SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed - 19 - [- - -] # 2 Background short Completed - 2 - [- - -] Long (extended) Self-test duration: 3600 seconds [60.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 4006:03 [240363 minutes] Number of background scans performed: 6, scan progress: 13.48% Number of background medium scans performed: 6 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5002538b71832fe2 attached SAS address = 0x500056b3e20feeff attached phy identifier = 0 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5002538b71832fe3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 /dev/da1 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.0-STABLE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SAMSUNG Product: MZILT960HBHQ/007 Revision: GXA0 Compliance: SPC-5 User Capacity: 960,197,124,096 bytes [960 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5002538b71832a80 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Apr 28 19:16:32 2022 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 0% Current temperature = 34 Lifetime maximum temperature = 44 Lifetime minimum temperature = 24 Maximum temperature since power on = 34 Minimum temperature since power on = 32 Manufactured in week 34 of year 2021 Accumulated start-stop cycles: 20 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 6.318 0 write: 0 0 0 0 0 5356.329 0 Non-medium error count: 133 Pending defect count:0 Pending Defects SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background long Completed - 19 - [- - -] # 2 Background short Completed - 2 - [- - -] Long (extended) Self-test duration: 3600 seconds [60.0 minutes] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 4006:06 [240366 minutes] Number of background scans performed: 6, scan progress: 13.48% Number of background medium scans performed: 6 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5002538b71832a82 attached SAS address = 0x500056b3e20feeff attached phy identifier = 1 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5002538b71832a83 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Received ERROR count: 0 Received address frame error count: 0 Received abandon-class OPEN_REJECT count: 0 Received retry-class OPEN_REJECT count: 0 Received SSP frame error count: 0