/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-STABLE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SSDPR-CX400-256-G2 Serial Number: -- Firmware Version: SBFM61.3 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jun 25 17:29:16 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 1 12 Power_Cycle_Count -O--C- 100 100 000 - 13 168 Unknown_Attribute -O--C- 100 100 000 - 0 170 Unknown_Attribute PO---- 100 100 010 - 171 173 Unknown_Attribute -O--C- 100 100 000 - 1 192 Power-Off_Retract_Count -O--C- 100 100 000 - 4 194 Temperature_Celsius PO---K 067 067 000 - 33 (Min/Max 33/33) 218 Unknown_Attribute PO-R-- 100 100 050 - 743 231 Unknown_SSD_Attribute PO--C- 100 100 000 - 100 241 Total_LBAs_Written -O--C- 100 100 000 - 30 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 13 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13 [12] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 40 00 00 00 e4 0f c0 e0 00 Error: ICRC, ABRT 64 sectors at LBA = 0x00e40fc0 = 14946240 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 40 00 00 00 e4 0f c0 e0 00 00:12:39.729 READ DMA c8 00 00 00 40 00 00 00 e4 0f 80 e0 00 00:12:39.725 READ DMA c8 00 00 00 40 00 00 00 e4 0f 40 e0 00 00:12:39.720 READ DMA c8 00 00 00 40 00 00 00 e4 0f 00 e0 00 00:12:39.716 READ DMA c8 00 00 00 40 00 00 00 c0 05 40 e0 00 00:12:39.712 READ DMA Error 12 [11] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 16 5f 46 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00165f46 = 1466182 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 7f 00 00 00 16 5f 46 e0 00 00:12:29.179 READ DMA c8 00 00 00 7f 00 00 00 16 5e c7 e0 00 00:12:29.179 READ DMA c8 00 00 00 7f 00 00 00 16 5e 48 e0 00 00:12:29.178 READ DMA c8 00 00 00 7f 00 00 00 16 5d c9 e0 00 00:12:29.178 READ DMA c8 00 00 00 7f 00 00 00 16 5d 4a e0 00 00:12:29.177 READ DMA Error 11 [10] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 1d 4f 88 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x001d4f88 = 1920904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 7f 00 00 00 1d 4f 88 e0 00 00:12:18.549 READ DMA c8 00 00 00 40 00 00 00 62 7c 00 e0 00 00:12:18.548 READ DMA c8 00 00 00 2a 00 00 00 29 17 da e0 00 00:12:18.539 READ DMA c8 00 00 00 7f 00 00 00 29 17 5b e0 00 00:12:18.539 READ DMA c8 00 00 00 7f 00 00 00 29 16 dc e0 00 00:12:18.538 READ DMA Error 10 [9] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 24 2b c7 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00242bc7 = 2370503 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 7f 00 00 00 24 2b c7 e0 00 00:12:07.891 READ DMA c8 00 00 00 7f 00 00 00 24 2b 48 e0 00 00:12:07.890 READ DMA c8 00 00 00 7f 00 00 00 24 2a c9 e0 00 00:12:07.890 READ DMA c8 00 00 00 7f 00 00 00 24 2a 4a e0 00 00:12:07.890 READ DMA c8 00 00 00 7f 00 00 00 24 29 cb e0 00 00:12:07.889 READ DMA Error 9 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 1b 4e 99 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x001b4e99 = 1789593 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 7f 00 00 00 1b 4e 99 e0 00 00:11:57.278 READ DMA c8 00 00 00 7f 00 00 00 1b 4e 1a e0 00 00:11:57.277 READ DMA c8 00 00 00 7f 00 00 00 1b 4d 9b e0 00 00:11:57.277 READ DMA c8 00 00 00 7f 00 00 00 1b 4d 1c e0 00 00:11:57.276 READ DMA c8 00 00 00 7f 00 00 00 1b 4c 9d e0 00 00:11:57.276 READ DMA Error 8 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 2e 3f 48 e1 00 Error: ICRC, ABRT 127 sectors at LBA = 0x012e3f48 = 19808072 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 7f 00 00 00 2e 3f 48 e1 00 00:11:46.967 READ DMA c8 00 00 00 40 00 00 00 64 95 c0 e0 00 00:11:46.966 READ DMA c8 00 00 00 40 00 00 00 0d c0 40 e0 00 00:11:46.966 READ DMA c8 00 00 00 40 00 00 00 2e 86 c0 e1 00 00:11:46.965 READ DMA c8 00 00 00 40 00 00 00 28 b9 40 e0 00 00:11:46.964 READ DMA Error 7 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 29 2b c0 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00292bc0 = 2698176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 7f 00 00 00 29 2b c0 e0 00 00:04:52.233 READ DMA c8 00 00 00 41 00 00 00 29 c2 38 e0 00 00:04:52.232 READ DMA c8 00 00 00 71 00 00 00 f8 cc 78 e0 00 00:04:52.230 READ DMA c8 00 00 00 06 00 00 00 2a 40 26 e0 00 00:04:52.228 READ DMA c8 00 00 00 7f 00 00 00 2a 3f a7 e0 00 00:04:52.228 READ DMA Error 6 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 2b 31 89 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x002b3189 = 2830729 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 7f 00 00 00 2b 31 89 e0 00 00:04:41.784 READ DMA c8 00 00 00 7f 00 00 00 2b 31 0a e0 00 00:04:41.783 READ DMA c8 00 00 00 7f 00 00 00 2b 30 8b e0 00 00:04:41.783 READ DMA c8 00 00 00 7f 00 00 00 2b 30 0c e0 00 00:04:41.782 READ DMA c8 00 00 00 7f 00 00 00 2b 2f 8d e0 00 00:04:41.782 READ DMA SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 13 --- Lifetime Power-On Resets 0x01 0x010 4 1 --- Power-on Hours 0x01 0x018 6 64492002 --- Logical Sectors Written 0x01 0x028 6 23695796 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 803 --- Number of Hardware Resets 0x06 0x018 4 743 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC