/dev/sd0 smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SK hynix SATA SSDs Device Model: HFS128G39TND-N210A Serial Number: -- Firmware Version: 30001P10 User Capacity: 128,035,676,160 bytes [128 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: M.2 TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 27 22:04:25 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x19) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 166 153 006 Pre-fail Always - 0 5 Retired_Block_Count 0x0032 100 100 036 Old_age Always - 5 9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 10282 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 1554 100 Total_Erase_Count 0x0032 100 100 000 Old_age Always - 27718900 168 Min_Erase_Count 0x0032 023 023 000 Old_age Always - 817 169 Max_Erase_Count 0x0032 017 017 000 Old_age Always - 885 171 Program_Fail_Count 0x0032 253 253 000 Old_age Always - 0 172 Erase_Fail_Count 0x0032 253 253 000 Old_age Always - 0 174 Unexpect_Power_Loss_Ct 0x0030 100 100 000 Old_age Offline - 73 175 Program_Fail_Count_Chip 0x0032 253 253 000 Old_age Always - 0 176 Unused_Rsvd_Blk_Cnt_Tot 0x0032 253 253 000 Old_age Always - 0 177 Wear_Leveling_Count 0x0032 021 021 000 Old_age Always - 848 178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 000 Old_age Always - 208 179 Used_Rsvd_Blk_Cnt_Tot 0x0032 100 100 000 Old_age Always - 431 180 Erase_Fail_Count 0x0032 100 100 000 Old_age Always - 2209 184 End-to-End_Error 0x0032 100 100 000 Old_age Always - 1326 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 1399 188 Command_Timeout 0x0032 253 253 000 Old_age Always - 0 194 Temperature_Celsius 0x0002 036 000 000 Old_age Always - 36 (Min/Max 10/53) 195 Hardware_ECC_Recovered 0x0032 100 091 000 Old_age Always - 4311110 196 Reallocated_Event_Count 0x0032 100 100 036 Old_age Always - 5 198 Offline_Uncorrectable 0x0032 100 100 000 Old_age Always - 152 199 UDMA_CRC_Error_Count 0x0032 253 253 000 Old_age Always - 0 204 Soft_ECC_Correction 0x000e 003 001 000 Old_age Always - 8496 212 Phy_Error_Count 0x0032 253 253 000 Old_age Always - 0 234 Unknown_SK_hynix_Attrib 0x0032 100 100 000 Old_age Always - 117074 241 Total_Writes_GB 0x0032 100 100 000 Old_age Always - 32892 242 Total_Reads_GB 0x0032 100 100 000 Old_age Always - 3087 250 Read_Retry_Count 0x0032 095 095 000 Old_age Always - 214854686 SMART Error Log Version: 1 ATA Error Count: 181 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 181 occurred at disk power-on lifetime: 10085 hours (420 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 e8 3c 9e 3d 40 40 01:28:14.740 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 01:28:14.730 READ LOG EXT 60 20 e0 3c 9e 3d 40 40 01:28:14.710 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 01:28:14.710 READ LOG EXT 60 20 d8 3c 9e 3d 40 40 01:28:14.690 READ FPDMA QUEUED Error 180 occurred at disk power-on lifetime: 10085 hours (420 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 e0 3c 9e 3d 40 40 01:28:14.710 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 01:28:14.710 READ LOG EXT 60 20 d8 3c 9e 3d 40 40 01:28:14.690 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 01:28:14.690 READ LOG EXT 60 20 d0 3c 9e 3d 40 40 01:28:14.670 READ FPDMA QUEUED Error 179 occurred at disk power-on lifetime: 10085 hours (420 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 d8 3c 9e 3d 40 40 01:28:14.690 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 01:28:14.690 READ LOG EXT 60 20 d0 3c 9e 3d 40 40 01:28:14.670 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 01:28:14.670 READ LOG EXT 60 20 c8 3c 9e 3d 40 40 01:28:14.650 READ FPDMA QUEUED Error 178 occurred at disk power-on lifetime: 10085 hours (420 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 d0 3c 9e 3d 40 40 01:28:14.670 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 01:28:14.670 READ LOG EXT 60 20 c8 3c 9e 3d 40 40 01:28:14.650 READ FPDMA QUEUED 61 20 c0 00 0a 25 40 40 01:28:13.810 WRITE FPDMA QUEUED 61 20 b8 40 0f 25 40 40 01:28:13.810 WRITE FPDMA QUEUED Error 177 occurred at disk power-on lifetime: 10085 hours (420 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 c8 3c 9e 3d 40 40 01:28:14.650 READ FPDMA QUEUED 61 20 c0 00 0a 25 40 40 01:28:13.810 WRITE FPDMA QUEUED 61 20 b8 40 0f 25 40 40 01:28:13.810 WRITE FPDMA QUEUED 61 20 b0 80 89 c2 40 40 01:28:13.590 WRITE FPDMA QUEUED 61 20 a8 40 89 c2 40 40 01:28:13.590 WRITE FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported The above only provides legacy SMART information - try 'smartctl -x' for more /dev/sd1 smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-21WN4A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 27 22:04:25 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11520) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 119) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 168 164 021 Pre-fail Always - 2566 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1549 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 10421 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1549 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 71 193 Load_Cycle_Count 0x0032 199 199 000 Old_age Always - 3783 194 Temperature_Celsius 0x0022 104 096 000 Old_age Always - 39 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. The above only provides legacy SMART information - try 'smartctl -x' for more /dev/sd2 smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sd2c failed: No medium found