/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE-p6 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: KINGSTON SA400S37240G Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: SBFK71E0 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Jan 9 11:34:06 2025 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 099 099 000 - 5 9 Power_On_Hours -O--C- 100 100 000 - 49313 12 Power_Cycle_Count -O--C- 100 100 000 - 305 148 Unknown_Attribute ------ 255 255 000 - 4 149 Unknown_Attribute ------ 255 255 000 - 32 167 Write_Protect_Mode -O---K 100 100 000 - 0 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 169 Bad_Block_Rate ------ 100 100 000 - 9 170 Bad_Blk_Ct_Lat/Erl PO--C- 100 100 010 - 0/10 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 MaxAvgErase_Ct ------ 100 100 000 - 61 (Average 37) 181 Program_Fail_Count -O--C- 100 100 000 - 0 182 Erase_Fail_Count ------ 255 255 000 - 1 187 Reported_Uncorrect -O--CK 100 100 000 - 2 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 288 194 Temperature_Celsius PO---K 072 051 000 - 28 (Min/Max 15/49) 196 Reallocated_Event_Count ------ 100 100 000 - 3 199 SATA_CRC_Error_Count -O--CK 100 100 000 - 0 218 CRC_Error_Count ------ 100 100 000 - 0 231 SSD_Life_Left PO--C- 100 100 000 - 96 233 Flash_Writes_GiB PO--C- 100 100 000 - 6367 241 Lifetime_Writes_GiB -O--C- 100 100 000 - 4044 242 Lifetime_Reads_GiB -O--C- 100 100 000 - 2250 244 Average_Erase_Count ------ 100 100 000 - 37 245 Max_Erase_Count ------ 100 100 000 - 61 246 Total_Erase_Count ------ 100 100 000 - 435504 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 aa 00 00 02 bf 13 70 40 00 Error: UNC 2218 sectors at LBA = 0x02bf1370 = 46076784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 aa 00 00 02 bf 13 70 40 00 00:00:00.000 READ DMA EXT 25 00 00 00 ce 00 00 00 5b 04 a0 40 00 00:00:00.000 READ DMA EXT 25 00 00 00 40 00 00 00 74 74 80 40 00 00:00:00.000 READ DMA EXT 25 00 00 01 31 00 00 00 da 1d 30 40 00 00:00:00.000 READ DMA EXT 25 00 00 01 7d 00 00 00 ef 16 60 40 00 00:00:00.000 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 04 78 e9 c0 40 00 Error: UNC 2048 sectors at LBA = 0x0478e9c0 = 75033024 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 04 78 e9 c0 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 04 78 e1 c0 40 00 00:00:00.000 READ DMA EXT 25 00 00 00 40 00 00 08 d8 94 80 40 00 00:00:00.000 READ DMA EXT 25 00 00 00 40 00 00 00 1a 9a 40 40 00 00:00:00.000 READ DMA EXT 25 00 00 00 40 00 00 08 d7 6c 80 40 00 00:00:00.000 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 01 3a ca 68 40 00 Error: UNC 2048 sectors at LBA = 0x013aca68 = 20630120 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 01 3a ca 68 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 01 3a ca 68 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 01 3a ca 68 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 00 75 e6 c0 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 01 2b 3a 00 40 00 00:00:00.000 READ DMA EXT Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 01 3a ca 68 40 00 Error: UNC 2048 sectors at LBA = 0x013aca68 = 20630120 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 01 3a ca 68 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 01 3a ca 68 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 00 75 e6 c0 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 01 2b 3a 00 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 00 ba 41 40 40 00 00:00:00.000 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 01 3a ca 68 40 00 Error: UNC 2048 sectors at LBA = 0x013aca68 = 20630120 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 01 3a ca 68 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 00 75 e6 c0 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 01 2b 3a 00 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 00 ba 41 40 40 00 00:00:00.000 READ DMA EXT 25 00 00 08 00 00 00 00 ba 41 58 40 00 00:00:00.000 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 305 --- Lifetime Power-On Resets 0x01 0x010 4 49313 --- Power-on Hours 0x01 0x018 6 8481234570 --- Logical Sectors Written 0x01 0x028 6 4720177092 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 5 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 --- Current Temperature 0x05 0x020 1 49 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 3 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 11 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC