/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Laptop HDD Device Model: ST500LT012-9WS142 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001SDM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Oct 30 00:35:20 2021 JST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 101) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 099 006 - 132040336 3 Spin_Up_Time PO---- 099 099 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1924 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 077 060 030 - 57855585 9 Power_On_Hours -O--CK 097 097 000 - 3133 (49 218 0) 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1922 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 086 086 000 - 14 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 073 052 045 - 27 (Min/Max 25/27) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 1963 192 Power-Off_Retract_Count -O--CK 100 100 000 - 32 193 Load_Cycle_Count -O--CK 029 029 000 - 142736 194 Temperature_Celsius -O---K 027 048 000 - 27 (0 8 0 0 0) 196 Reallocated_Event_Count POSR-- 098 098 030 - 1929 (48428 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 098 098 000 - 1929 (189 44 0) 241 Total_LBAs_Written ------ 100 253 000 - 3202912795 242 Total_LBAs_Read ------ 100 253 000 - 451542242 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbd-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 14 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 14 [13] occurred at disk power-on lifetime: 183 hours (7 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 ab a1 8f 00 00 Error: UNC at LBA = 0x00aba18f = 11248015 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 ab a1 8f 40 00 01:09:23.319 READ FPDMA QUEUED 60 00 00 00 f0 00 00 04 41 da 78 40 00 01:09:23.260 READ FPDMA QUEUED 61 00 00 00 18 00 00 00 86 8c 20 40 00 01:09:23.260 WRITE FPDMA QUEUED ec 00 00 00 00 00 00 00 00 00 00 00 00 01:09:22.670 IDENTIFY DEVICE ef 00 10 00 03 00 00 00 00 00 00 00 00 01:09:22.660 SET FEATURES [Enable SATA feature] Error 13 [12] occurred at disk power-on lifetime: 183 hours (7 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 ab a1 8f 00 00 Error: UNC at LBA = 0x00aba18f = 11248015 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 ab a1 8f 40 00 01:09:19.478 READ FPDMA QUEUED 60 00 00 00 20 00 00 04 20 9e 88 40 00 01:09:19.316 READ FPDMA QUEUED 60 00 00 00 60 00 00 04 20 9e 28 40 00 01:09:19.314 READ FPDMA QUEUED 60 00 00 00 20 00 00 04 20 9e a8 40 00 01:09:19.300 READ FPDMA QUEUED 60 00 00 00 90 00 00 04 20 9e c8 40 00 01:09:19.296 READ FPDMA QUEUED Error 12 [11] occurred at disk power-on lifetime: 183 hours (7 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 ab a1 8e 00 00 Error: UNC at LBA = 0x00aba18e = 11248014 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 ab a1 8e 40 00 01:09:16.234 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 29 8a 58 40 00 01:09:16.184 WRITE FPDMA QUEUED 60 00 00 00 85 00 00 03 cc 22 f8 40 00 01:09:15.922 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 28 00 01:09:15.902 READ LOG EXT 60 00 00 00 01 00 00 00 ab a1 8d 40 00 01:09:13.288 READ FPDMA QUEUED Error 11 [10] occurred at disk power-on lifetime: 183 hours (7 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 ab a1 8d 00 00 Error: UNC at LBA = 0x00aba18d = 11248013 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 ab a1 8d 40 00 01:09:13.288 READ FPDMA QUEUED 60 00 00 00 f0 00 00 03 cc 22 08 40 00 01:09:13.234 READ FPDMA QUEUED ec 00 00 00 00 00 00 00 00 00 00 00 00 01:09:12.746 IDENTIFY DEVICE ef 00 10 00 03 00 00 00 00 00 00 00 00 01:09:12.736 SET FEATURES [Enable SATA feature] ef 00 10 00 03 00 00 00 00 00 00 a0 00 01:09:12.715 SET FEATURES [Enable SATA feature] Error 10 [9] occurred at disk power-on lifetime: 183 hours (7 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 ab a1 8d 00 00 Error: UNC at LBA = 0x00aba18d = 11248013 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 ab a1 8d 40 00 01:09:09.616 READ FPDMA QUEUED 60 00 00 00 a4 00 00 03 a8 dd 00 40 00 01:09:09.589 READ FPDMA QUEUED 60 00 00 00 10 00 00 04 42 6d f0 40 00 01:09:09.302 READ FPDMA QUEUED 60 00 00 00 f0 00 00 04 42 57 20 40 00 01:09:09.289 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 85 70 a0 40 00 01:09:09.287 WRITE FPDMA QUEUED Error 9 [8] occurred at disk power-on lifetime: 183 hours (7 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 ab a1 8c 00 00 Error: UNC at LBA = 0x00aba18c = 11248012 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 ab a1 8c 40 00 01:09:06.499 READ FPDMA QUEUED 60 00 00 00 20 00 00 03 61 a6 a8 40 00 01:09:06.444 READ FPDMA QUEUED 60 00 00 00 f0 00 00 03 61 a5 b8 40 00 01:09:06.434 READ FPDMA QUEUED 60 00 00 01 00 00 00 04 42 71 b0 40 00 01:09:06.407 READ FPDMA QUEUED 60 00 00 00 f0 00 00 04 42 70 c0 40 00 01:09:06.398 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 183 hours (7 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 ab a1 8b 00 00 Error: UNC at LBA = 0x00aba18b = 11248011 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 ab a1 8b 40 00 01:09:03.489 READ FPDMA QUEUED 60 00 00 00 60 00 00 03 61 ae 20 40 00 01:09:03.438 READ FPDMA QUEUED 60 00 00 00 10 00 00 03 61 ae 10 40 00 01:09:03.434 READ FPDMA QUEUED 60 00 00 01 00 00 00 03 61 ad 10 40 00 01:09:03.433 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 31 6a a8 40 00 01:09:03.433 WRITE FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 183 hours (7 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 ab a1 8a 00 00 Error: UNC at LBA = 0x00aba18a = 11248010 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 ab a1 8a 40 00 01:09:00.669 READ FPDMA QUEUED 60 00 00 00 81 00 00 02 e7 85 20 40 00 01:09:00.618 READ FPDMA QUEUED 60 00 00 00 f0 00 00 02 e7 84 30 40 00 01:09:00.489 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 28 00 01:09:00.469 READ LOG EXT 60 00 00 00 01 00 00 00 ab a1 89 40 00 01:08:57.848 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 25/27 Celsius Lifetime Min/Max Temperature: 8/48 Celsius Specified Max Operating Temperature: 34 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 30 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (22) Index Estimated Time Temperature Celsius 23 2021-10-27 09:00 27 ******** 24 2021-10-27 09:30 36 ***************** 25 2021-10-27 10:00 ? - 26 2021-10-27 10:30 25 ****** 27 2021-10-27 11:00 ? - 28 2021-10-27 11:30 17 - 29 2021-10-27 12:00 19 - 30 2021-10-27 12:30 27 ******** 31 2021-10-27 13:00 ? - 32 2021-10-27 13:30 28 ********* 33 2021-10-27 14:00 ? - 34 2021-10-27 14:30 28 ********* 35 2021-10-27 15:00 ? - 36 2021-10-27 15:30 28 ********* 37 2021-10-27 16:00 ? - 38 2021-10-27 16:30 30 *********** 39 2021-10-27 17:00 ? - 40 2021-10-27 17:30 30 *********** 41 2021-10-27 18:00 ? - 42 2021-10-27 18:30 30 *********** 43 2021-10-27 19:00 ? - 44 2021-10-27 19:30 32 ************* 45 2021-10-27 20:00 ? - 46 2021-10-27 20:30 25 ****** 47 2021-10-27 21:00 ? - 48 2021-10-27 21:30 17 - 49 2021-10-27 22:00 18 - 50 2021-10-27 22:30 29 ********** 51 2021-10-27 23:00 32 ************* 52 2021-10-27 23:30 33 ************** 53 2021-10-28 00:00 33 ************** 54 2021-10-28 00:30 34 *************** 55 2021-10-28 01:00 33 ************** 56 2021-10-28 01:30 33 ************** 57 2021-10-28 02:00 32 ************* 58 2021-10-28 02:30 26 ******* 59 2021-10-28 03:00 ? - 60 2021-10-28 03:30 23 **** 61 2021-10-28 04:00 ? - 62 2021-10-28 04:30 26 ******* 63 2021-10-28 05:00 ? - 64 2021-10-28 05:30 33 ************** 65 2021-10-28 06:00 ? - 66 2021-10-28 06:30 29 ********** 67 2021-10-28 07:00 ? - 68 2021-10-28 07:30 30 *********** 69 2021-10-28 08:00 ? - 70 2021-10-28 08:30 31 ************ 71 2021-10-28 09:00 32 ************* 72 2021-10-28 09:30 33 ************** 73 2021-10-28 10:00 34 *************** 74 2021-10-28 10:30 33 ************** 75 2021-10-28 11:00 32 ************* 76 2021-10-28 11:30 31 ************ ... ..( 4 skipped). .. ************ 81 2021-10-28 14:00 31 ************ 82 2021-10-28 14:30 ? - 83 2021-10-28 15:00 31 ************ 84 2021-10-28 15:30 ? - 85 2021-10-28 16:00 31 ************ 86 2021-10-28 16:30 ? - 87 2021-10-28 17:00 29 ********** 88 2021-10-28 17:30 ? - 89 2021-10-28 18:00 28 ********* 90 2021-10-28 18:30 ? - 91 2021-10-28 19:00 28 ********* 92 2021-10-28 19:30 ? - 93 2021-10-28 20:00 31 ************ 94 2021-10-28 20:30 ? - 95 2021-10-28 21:00 31 ************ 96 2021-10-28 21:30 ? - 97 2021-10-28 22:00 34 *************** 98 2021-10-28 22:30 ? - 99 2021-10-28 23:00 35 **************** 100 2021-10-28 23:30 ? - 101 2021-10-29 00:00 32 ************* 102 2021-10-29 00:30 ? - 103 2021-10-29 01:00 24 ***** 104 2021-10-29 01:30 34 *************** 105 2021-10-29 02:00 37 ****************** 106 2021-10-29 02:30 ? - 107 2021-10-29 03:00 36 ***************** 108 2021-10-29 03:30 ? - 109 2021-10-29 04:00 24 ***** 110 2021-10-29 04:30 ? - 111 2021-10-29 05:00 28 ********* 112 2021-10-29 05:30 ? - 113 2021-10-29 06:00 28 ********* 114 2021-10-29 06:30 29 ********** 115 2021-10-29 07:00 34 *************** 116 2021-10-29 07:30 ? - 117 2021-10-29 08:00 24 ***** 118 2021-10-29 08:30 35 **************** 119 2021-10-29 09:00 35 **************** 120 2021-10-29 09:30 ? - 121 2021-10-29 10:00 24 ***** 122 2021-10-29 10:30 ? - 123 2021-10-29 11:00 25 ****** 124 2021-10-29 11:30 ? - 125 2021-10-29 12:00 25 ****** 126 2021-10-29 12:30 ? - 127 2021-10-29 13:00 23 **** 0 2021-10-29 13:30 ? - 1 2021-10-29 14:00 35 **************** 2 2021-10-29 14:30 ? - 3 2021-10-29 15:00 25 ****** 4 2021-10-29 15:30 ? - 5 2021-10-29 16:00 27 ******** 6 2021-10-29 16:30 ? - 7 2021-10-29 17:00 26 ******* 8 2021-10-29 17:30 27 ******** 9 2021-10-29 18:00 38 ******************* 10 2021-10-29 18:30 ? - 11 2021-10-29 19:00 27 ******** 12 2021-10-29 19:30 27 ******** 13 2021-10-29 20:00 37 ****************** 14 2021-10-29 20:30 ? - 15 2021-10-29 21:00 25 ****** 16 2021-10-29 21:30 ? - 17 2021-10-29 22:00 19 - 18 2021-10-29 22:30 ? - 19 2021-10-29 23:00 21 ** 20 2021-10-29 23:30 ? - 21 2021-10-30 00:00 25 ****** 22 2021-10-30 00:30 26 ******* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS