/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.2-RELEASE-p1 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba P300 (CMR) Device Model: TOSHIBA HDWD130 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MX6OACF0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 12 19:59:22 2025 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (23513) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 392) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 139 139 054 - 70 3 Spin_Up_Time POS--- 165 165 024 - 402 (Average 294) 4 Start_Stop_Count -O--C- 099 099 000 - 6196 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 094 094 000 - 44980 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 5121 192 Power-Off_Retract_Count -O--CK 075 075 000 - 31148 193 Load_Cycle_Count -O--C- 075 075 000 - 31148 194 Temperature_Celsius -O---- 222 222 000 - 27 (Min/Max 12/62) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 1385 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1385 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1385 [0] occurred at disk power-on lifetime: 37065 hours (1544 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 a1 00 00 94 d4 a1 5f 04 00 Error: ICRC, ABRT at LBA = 0x94d4a15f = 2496962911 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 58 00 00 94 d4 a1 00 40 00 02:39:51.417 READ FPDMA QUEUED 60 01 00 00 50 00 00 94 d4 a0 00 40 00 02:39:51.416 READ FPDMA QUEUED 60 01 00 00 48 00 00 94 d4 9f 00 40 00 02:39:51.415 READ FPDMA QUEUED 60 01 00 00 40 00 00 94 d4 9e 00 40 00 02:39:51.415 READ FPDMA QUEUED 60 01 00 00 38 00 00 94 d4 9d 00 40 00 02:39:51.414 READ FPDMA QUEUED Error 1384 [3] occurred at disk power-on lifetime: 24971 hours (1040 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 29 00 00 00 00 02 d7 00 00 Error: ICRC, ABRT at LBA = 0x000002d7 = 727 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 f8 00 08 00 00 00 00 02 08 40 00 00:01:18.694 READ FPDMA QUEUED 60 00 08 00 00 00 00 00 00 01 f8 40 00 00:01:18.694 READ FPDMA QUEUED 60 00 08 00 f0 00 00 00 00 01 f0 40 00 00:01:18.694 READ FPDMA QUEUED 60 00 08 00 e8 00 00 00 00 01 e8 40 00 00:01:18.694 READ FPDMA QUEUED 60 00 08 00 e0 00 00 00 00 01 e0 40 00 00:01:18.694 READ FPDMA QUEUED Error 1383 [2] occurred at disk power-on lifetime: 24971 hours (1040 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 49 00 00 00 00 01 b7 00 00 Error: ICRC, ABRT at LBA = 0x000001b7 = 439 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 f8 00 c8 00 00 00 00 01 08 40 00 00:01:18.331 READ FPDMA QUEUED 60 00 78 00 c0 00 00 00 00 00 88 40 00 00:01:18.331 READ FPDMA QUEUED 60 00 30 00 b8 00 00 00 00 00 48 40 00 00:01:18.331 READ FPDMA QUEUED 60 00 10 00 b0 00 00 00 00 00 28 40 00 00:01:18.331 READ FPDMA QUEUED 60 00 08 00 a8 00 00 00 00 00 10 40 00 00:01:18.331 READ FPDMA QUEUED Error 1382 [1] occurred at disk power-on lifetime: 24971 hours (1040 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 11 00 00 00 00 00 67 00 00 Error: ICRC, ABRT at LBA = 0x00000067 = 103 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 f8 00 c8 00 00 00 00 01 08 40 00 00:01:14.463 READ FPDMA QUEUED 60 00 78 00 c0 00 00 00 00 00 88 40 00 00:01:14.463 READ FPDMA QUEUED 60 00 30 00 b8 00 00 00 00 00 48 40 00 00:01:14.463 READ FPDMA QUEUED 60 00 10 00 b0 00 00 00 00 00 28 40 00 00:01:14.463 READ FPDMA QUEUED 60 00 08 00 a8 00 00 00 00 00 10 40 00 00:01:14.463 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 23/27 Celsius Lifetime Min/Max Temperature: 12/62 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (113) Index Estimated Time Temperature Celsius 114 2025-02-12 17:52 30 *********** ... ..( 33 skipped). .. *********** 20 2025-02-12 18:26 30 *********** 21 2025-02-12 18:27 29 ********** 22 2025-02-12 18:28 30 *********** 23 2025-02-12 18:29 30 *********** 24 2025-02-12 18:30 29 ********** 25 2025-02-12 18:31 30 *********** 26 2025-02-12 18:32 30 *********** 27 2025-02-12 18:33 29 ********** ... ..( 2 skipped). .. ********** 30 2025-02-12 18:36 29 ********** 31 2025-02-12 18:37 30 *********** 32 2025-02-12 18:38 29 ********** ... ..( 6 skipped). .. ********** 39 2025-02-12 18:45 29 ********** 40 2025-02-12 18:46 30 *********** 41 2025-02-12 18:47 29 ********** ... ..( 35 skipped). .. ********** 77 2025-02-12 19:23 29 ********** 78 2025-02-12 19:24 ? - 79 2025-02-12 19:25 29 ********** ... ..( 3 skipped). .. ********** 83 2025-02-12 19:29 29 ********** 84 2025-02-12 19:30 ? - 85 2025-02-12 19:31 ? - 86 2025-02-12 19:32 22 *** 87 2025-02-12 19:33 23 **** 88 2025-02-12 19:34 23 **** 89 2025-02-12 19:35 ? - 90 2025-02-12 19:36 24 ***** 91 2025-02-12 19:37 24 ***** 92 2025-02-12 19:38 24 ***** 93 2025-02-12 19:39 25 ****** 94 2025-02-12 19:40 25 ****** 95 2025-02-12 19:41 25 ****** 96 2025-02-12 19:42 26 ******* ... ..( 6 skipped). .. ******* 103 2025-02-12 19:49 26 ******* 104 2025-02-12 19:50 27 ******** ... ..( 8 skipped). .. ******** 113 2025-02-12 19:59 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 5121 --- Lifetime Power-On Resets 0x01 0x010 4 44980 --- Power-on Hours 0x01 0x018 6 228799969779 --- Logical Sectors Written 0x01 0x020 6 1905378968 --- Number of Write Commands 0x01 0x028 6 162903983341 --- Logical Sectors Read 0x01 0x030 6 1695247263 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 41021 --- Spindle Motor Power-on Hours 0x03 0x010 4 41019 --- Head Flying Hours 0x03 0x018 4 31148 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1246 --- Read Recovery Attempts 0x03 0x030 4 6 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 9 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 3709 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 27 --- Current Temperature 0x05 0x010 1 27 N-- Average Short Term Temperature 0x05 0x018 1 40 N-- Average Long Term Temperature 0x05 0x020 1 62 --- Highest Temperature 0x05 0x028 1 12 --- Lowest Temperature 0x05 0x030 1 56 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 51 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 140 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 64355 --- Number of Hardware Resets 0x06 0x010 4 57756 --- Number of ASR Events 0x06 0x018 4 1385 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/nda0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.2-RELEASE-p1 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/nda0 failed: INQUIRY failed