/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p5 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K500.B Device Model: Hitachi HTS545050B9A300 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: PB4OCA1G User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Jan 18 09:04:36 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 158) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 075 062 - 0 2 Throughput_Performance P-S--K 100 100 040 - 0 3 Spin_Up_Time PO---K 232 100 033 - 2 4 Start_Stop_Count -O--CK 097 097 000 - 4989 5 Reallocated_Sector_Ct PO--CK 059 056 005 - 3103 (0 1738) 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 100 100 040 - 0 9 Power_On_Hours -O--CK 079 079 000 - 9505 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 4727 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 281470717947710 188 Command_Timeout -O--CK 100 001 000 - 330726837163 190 Airflow_Temperature_Cel -O---K 070 054 045 - 30 (Min/Max 28/30) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 57 192 Power-Off_Retract_Count -O--CK 100 100 000 - 6094941 193 Load_Cycle_Count -O--CK 001 001 000 - 1097261 196 Reallocated_Event_Count -O--CK 056 056 000 - 2395 197 Current_Pending_Sector -O--CK 098 093 000 - 530 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 4189 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4189 [0] occurred at disk power-on lifetime: 5645 hours (235 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 02 10 56 0e 42 00 Error: UNC at LBA = 0x0210560e = 34625038 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 08 00 00 02 10 56 08 40 00 01:38:05.000 READ VERIFY SECTOR(S) EXT 42 00 00 00 08 00 00 02 10 56 08 40 00 01:37:56.700 READ VERIFY SECTOR(S) EXT 42 00 00 00 08 00 00 02 10 56 00 40 00 01:37:52.600 READ VERIFY SECTOR(S) EXT ec 00 00 00 00 00 00 00 00 00 00 00 00 01:37:52.600 IDENTIFY DEVICE ef 00 02 00 00 00 00 00 00 00 00 40 00 01:37:52.600 SET FEATURES [Enable write cache] Error 4188 [3] occurred at disk power-on lifetime: 5645 hours (235 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 03 00 00 02 10 56 0d 42 00 Error: UNC at LBA = 0x0210560d = 34625037 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 08 00 00 02 10 56 08 40 00 01:37:56.700 READ VERIFY SECTOR(S) EXT 42 00 00 00 08 00 00 02 10 56 00 40 00 01:37:52.600 READ VERIFY SECTOR(S) EXT ec 00 00 00 00 00 00 00 00 00 00 00 00 01:37:52.600 IDENTIFY DEVICE ef 00 02 00 00 00 00 00 00 00 00 40 00 01:37:52.600 SET FEATURES [Enable write cache] ef 00 03 00 45 00 00 00 00 00 00 40 00 01:37:52.600 SET FEATURES [Set transfer mode] Error 4187 [2] occurred at disk power-on lifetime: 5645 hours (235 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 02 10 56 06 42 00 Error: UNC at LBA = 0x02105606 = 34625030 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 08 00 00 02 10 56 00 40 00 01:37:52.600 READ VERIFY SECTOR(S) EXT ec 00 00 00 00 00 00 00 00 00 00 00 00 01:37:52.600 IDENTIFY DEVICE ef 00 02 00 00 00 00 00 00 00 00 40 00 01:37:52.600 SET FEATURES [Enable write cache] ef 00 03 00 45 00 00 00 00 00 00 40 00 01:37:52.600 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 01:37:52.600 SET MULTIPLE MODE Error 4186 [1] occurred at disk power-on lifetime: 5645 hours (235 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 02 10 56 06 42 00 Error: UNC at LBA = 0x02105606 = 34625030 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 08 00 00 02 10 56 00 40 00 01:36:20.500 READ VERIFY SECTOR(S) EXT 42 00 00 00 08 00 00 02 10 56 00 40 00 01:36:16.800 READ VERIFY SECTOR(S) EXT 42 00 00 00 08 00 00 02 10 56 00 40 00 01:36:11.100 READ VERIFY SECTOR(S) EXT 42 00 00 00 08 00 00 02 10 56 00 40 00 01:36:03.800 READ VERIFY SECTOR(S) EXT 42 00 00 00 08 00 00 02 10 56 00 40 00 01:36:00.100 READ VERIFY SECTOR(S) EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 28/30 Celsius Lifetime Min/Max Temperature: 12/46 Celsius Specified Max Operating Temperature: 29 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 478 (166) Index Estimated Time Temperature Celsius 167 2023-01-18 01:07 28 ********* ... ..(119 skipped). .. ********* 287 2023-01-18 03:07 28 ********* 288 2023-01-18 03:08 29 ********** 289 2023-01-18 03:09 28 ********* 290 2023-01-18 03:10 29 ********** 291 2023-01-18 03:11 28 ********* 292 2023-01-18 03:12 29 ********** 293 2023-01-18 03:13 28 ********* ... ..(281 skipped). .. ********* 97 2023-01-18 07:55 28 ********* 98 2023-01-18 07:56 29 ********** ... ..( 33 skipped). .. ********** 132 2023-01-18 08:30 29 ********** 133 2023-01-18 08:31 28 ********* 134 2023-01-18 08:32 28 ********* 135 2023-01-18 08:33 28 ********* 136 2023-01-18 08:34 29 ********** ... ..( 28 skipped). .. ********** 165 2023-01-18 09:03 29 ********** 166 2023-01-18 09:04 30 *********** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS