/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.2-STABLE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: HGST Travelstar 5K1000 Device Model: HGST HTS541010A9E680 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JA0OA710 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 11 10:35:06 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 239) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 070 062 - 0 2 Throughput_Performance P-S--K 100 100 040 - 0 3 Spin_Up_Time PO---K 189 100 033 - 1 4 Start_Stop_Count -O--CK 098 098 000 - 4244 5 Reallocated_Sector_Ct PO--CK 095 067 005 - 1440 (0 112) 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 100 100 040 - 0 9 Power_On_Hours -O--CK 093 093 000 - 3403 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 3525 183 Runtime_Bad_Block -O--CK 099 099 000 - 1 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 001 000 - 222741306158116 188 Command_Timeout -O--CK 100 100 000 - 193281589249 190 Airflow_Temperature_Cel -O---K 066 057 045 - 34 (Min/Max 26/34) 191 G-Sense_Error_Rate -O--CK 083 083 000 - 4604 192 Power-Off_Retract_Count -O--CK 100 100 000 - 6553700 193 Load_Cycle_Count -O--CK 092 092 000 - 83022 196 Reallocated_Event_Count -O--CK 100 100 000 - 130 197 Current_Pending_Sector -O--CK 035 001 000 - 1704 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 11300 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 11300 [3] occurred at disk power-on lifetime: 3239 hours (134 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 30 00 00 08 8f fc 50 08 00 Error: WP at LBA = 0x088ffc50 = 143653968 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 b8 00 00 00 34 0d e0 40 00 01:57:06.432 WRITE FPDMA QUEUED 61 00 20 00 b0 00 00 09 17 43 a0 40 00 01:57:06.431 WRITE FPDMA QUEUED 61 00 20 00 a8 00 00 09 23 2b e0 40 00 01:57:06.431 WRITE FPDMA QUEUED 61 00 20 00 a0 00 00 00 33 f1 e0 40 00 01:57:06.428 WRITE FPDMA QUEUED 61 00 20 00 98 00 00 09 17 43 a0 40 00 01:57:06.428 WRITE FPDMA QUEUED Error 11299 [2] occurred at disk power-on lifetime: 3239 hours (134 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 08 8f fc 50 08 00 Error: UNC at LBA = 0x088ffc50 = 143653968 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e8 00 00 08 8f fb 68 40 00 01:57:02.572 READ FPDMA QUEUED 61 00 10 00 e0 00 00 00 7c 65 00 40 00 01:57:02.572 WRITE FPDMA QUEUED 60 00 f8 00 d8 00 00 08 8f fb 70 40 00 01:57:02.572 READ FPDMA QUEUED 61 00 08 00 d0 00 00 04 bb f1 68 40 00 01:57:02.572 WRITE FPDMA QUEUED 61 00 08 00 c8 00 00 00 81 ae b8 40 00 01:57:02.571 WRITE FPDMA QUEUED Error 11298 [1] occurred at disk power-on lifetime: 3239 hours (134 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 08 8f fc 50 08 00 Error: UNC at LBA = 0x088ffc50 = 143653968 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 b8 00 00 08 8f fb 68 40 00 01:56:58.885 READ FPDMA QUEUED 60 01 00 00 b0 00 00 08 8f fa 68 40 00 01:56:58.883 READ FPDMA QUEUED 60 01 00 00 a8 00 00 08 8f f9 68 40 00 01:56:58.883 READ FPDMA QUEUED 60 01 00 00 a0 00 00 08 8f f8 68 40 00 01:56:58.882 READ FPDMA QUEUED 60 01 00 00 98 00 00 08 8f f7 68 40 00 01:56:58.880 READ FPDMA QUEUED Error 11297 [0] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 90 00 00 08 90 a3 38 08 00 Error: WP at LBA = 0x0890a338 = 143696696 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 10 00 00 08 3e 04 30 40 00 00:54:28.848 WRITE FPDMA QUEUED 61 01 00 00 08 00 00 08 3e 03 30 40 00 00:54:28.848 WRITE FPDMA QUEUED 61 01 00 00 00 00 00 08 3e 02 30 40 00 00:54:28.848 WRITE FPDMA QUEUED 61 01 00 00 f8 00 00 08 3e 01 30 40 00 00:54:28.848 WRITE FPDMA QUEUED 61 01 00 00 f0 00 00 08 3e 00 30 40 00 00:54:28.848 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 3378 466716352 # 2 Short offline Completed: read failure 90% 3376 466716352 # 3 Short offline Completed: read failure 90% 3374 466716352 # 4 Short offline Completed: read failure 90% 3371 466716352 # 5 Extended offline Completed: read failure 90% 3357 466716352 # 6 Extended offline Completed: read failure 90% 3342 466716352 # 7 Short offline Completed: read failure 90% 3340 466716352 # 8 Extended offline Completed: read failure 90% 3338 466716352 # 9 Extended offline Completed: read failure 90% 3336 466716352 #10 Short offline Completed: read failure 90% 3335 466716352 #11 Short offline Completed: read failure 90% 3333 466716352 #12 Short offline Completed: read failure 90% 3332 466716352 #13 Short offline Completed: read failure 90% 3307 466660944 #14 Short offline Completed: read failure 90% 3306 466716352 #15 Short offline Completed: read failure 90% 3303 466660944 #16 Short offline Completed: read failure 90% 3303 466660944 #17 Short offline Completed: read failure 90% 3300 143653968 #18 Short offline Completed: read failure 90% 3299 466660944 #19 Short offline Completed: read failure 90% 3297 466660944 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 26/34 Celsius Lifetime Min/Max Temperature: 17/43 Celsius Specified Max Operating Temperature: 31 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (29) Index Estimated Time Temperature Celsius 30 2023-06-11 08:28 29 ********** 31 2023-06-11 08:29 29 ********** 32 2023-06-11 08:30 30 *********** 33 2023-06-11 08:31 30 *********** 34 2023-06-11 08:32 32 ************* 35 2023-06-11 08:33 32 ************* 36 2023-06-11 08:34 32 ************* 37 2023-06-11 08:35 33 ************** 38 2023-06-11 08:36 33 ************** 39 2023-06-11 08:37 34 *************** ... ..( 2 skipped). .. *************** 42 2023-06-11 08:40 34 *************** 43 2023-06-11 08:41 35 **************** 44 2023-06-11 08:42 35 **************** 45 2023-06-11 08:43 35 **************** 46 2023-06-11 08:44 36 ***************** ... ..( 12 skipped). .. ***************** 59 2023-06-11 08:57 36 ***************** 60 2023-06-11 08:58 37 ****************** 61 2023-06-11 08:59 36 ***************** ... ..( 5 skipped). .. ***************** 67 2023-06-11 09:05 36 ***************** 68 2023-06-11 09:06 35 **************** ... ..( 3 skipped). .. **************** 72 2023-06-11 09:10 35 **************** 73 2023-06-11 09:11 34 *************** 74 2023-06-11 09:12 34 *************** 75 2023-06-11 09:13 ? - 76 2023-06-11 09:14 35 **************** ... ..( 7 skipped). .. **************** 84 2023-06-11 09:22 35 **************** 85 2023-06-11 09:23 36 ***************** ... ..( 14 skipped). .. ***************** 100 2023-06-11 09:38 36 ***************** 101 2023-06-11 09:39 37 ****************** ... ..( 2 skipped). .. ****************** 104 2023-06-11 09:42 37 ****************** 105 2023-06-11 09:43 38 ******************* ... ..( 11 skipped). .. ******************* 117 2023-06-11 09:55 38 ******************* 118 2023-06-11 09:56 39 ******************** 119 2023-06-11 09:57 39 ******************** 120 2023-06-11 09:58 38 ******************* ... ..( 4 skipped). .. ******************* 125 2023-06-11 10:03 38 ******************* 126 2023-06-11 10:04 ? - 127 2023-06-11 10:05 26 ******* 0 2023-06-11 10:06 27 ******** 1 2023-06-11 10:07 27 ******** 2 2023-06-11 10:08 28 ********* 3 2023-06-11 10:09 29 ********** 4 2023-06-11 10:10 29 ********** 5 2023-06-11 10:11 29 ********** 6 2023-06-11 10:12 30 *********** 7 2023-06-11 10:13 30 *********** 8 2023-06-11 10:14 30 *********** 9 2023-06-11 10:15 31 ************ ... ..( 2 skipped). .. ************ 12 2023-06-11 10:18 31 ************ 13 2023-06-11 10:19 32 ************* ... ..( 3 skipped). .. ************* 17 2023-06-11 10:23 32 ************* 18 2023-06-11 10:24 33 ************** ... ..( 5 skipped). .. ************** 24 2023-06-11 10:30 33 ************** 25 2023-06-11 10:31 34 *************** ... ..( 3 skipped). .. *************** 29 2023-06-11 10:35 34 *************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS