/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.1-RELEASE-p12-HBSD amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SanDisk based SSDs Device Model: SanDisk SSD i100 32GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: 11.56.00 User Capacity: 32,017,047,552 bytes [32.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 1.8 inches TRIM Command: Available, deterministic Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Feb 5 17:01:03 2021 -04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 7) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O---- 100 100 000 - 0 9 Power_On_Hours -O---- 100 100 000 - 33871 12 Power_Cycle_Count -O---- 100 100 000 - 68 171 Program_Fail_Count -O---- 100 100 000 - 0 172 Erase_Fail_Count -O---- 100 100 000 - 0 173 Avg_Write/Erase_Count -O---- 100 100 000 - 328 174 Unexpect_Power_Loss_Ct -O---- 100 100 000 - 58 187 Reported_Uncorrect -O---- 100 100 000 - 12 230 Perc_Write/Erase_Count -O---- 100 100 000 - 1093 232 Perc_Avail_Resrvd_Space PO---- 100 100 005 - 0 234 Perc_Write/Erase_Ct_BC -O---- 100 100 000 - 10000 241 Total_LBAs_Written -O---- 100 100 000 - 114807888 242 Total_LBAs_Read -O---- 100 100 000 - 14325389 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x03 GPL,SL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) Device Error Count: 12 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [11] occurred at disk power-on lifetime: 31505 hours (1312 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c3 0a a8 00 00 Error: UNC Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+08:23:01.892 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+08:23:01.855 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+08:23:01.807 READ LOG EXT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.884 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.882 DATA SET MANAGEMENT Error 11 [10] occurred at disk power-on lifetime: 31505 hours (1312 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c3 0a a8 00 00 Error: UNC Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+08:23:01.855 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+08:23:01.807 READ LOG EXT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.884 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.882 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.869 DATA SET MANAGEMENT Error 10 [9] occurred at disk power-on lifetime: 31505 hours (1312 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c3 0a a8 00 00 Error: UNC Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 00 26d+08:23:01.807 READ LOG EXT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.884 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.882 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.869 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.868 DATA SET MANAGEMENT Error 9 [8] occurred at disk power-on lifetime: 31505 hours (1312 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c3 0a a8 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.884 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.882 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.869 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.868 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 26d+08:22:59.428 DATA SET MANAGEMENT Error 8 [7] occurred at disk power-on lifetime: 31482 hours (1311 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c3 0a a8 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 40 00 25d+09:16:55.315 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 25d+09:16:55.313 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 25d+09:16:55.305 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 25d+09:16:55.303 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 25d+09:16:55.288 DATA SET MANAGEMENT Error 7 [6] occurred at disk power-on lifetime: 31337 hours (1305 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c3 0a a8 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 40 00 19d+08:29:12.624 DATA SET MANAGEMENT 06 00 01 00 02 00 00 00 00 00 00 40 00 19d+08:29:12.620 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 19d+08:29:12.601 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 19d+08:29:12.183 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 19d+08:29:12.177 DATA SET MANAGEMENT Error 6 [5] occurred at disk power-on lifetime: 31265 hours (1302 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c3 0a a8 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 06 00 01 00 01 00 00 00 00 00 00 40 00 16d+08:20:13.534 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 16d+08:20:02.746 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 16d+08:20:02.696 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 16d+08:20:02.216 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 16d+08:20:02.216 DATA SET MANAGEMENT Error 5 [4] occurred at disk power-on lifetime: 31169 hours (1298 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 c3 0a a8 00 00 Error: UNC Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 00 12d+08:19:17.678 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 12d+08:19:17.640 READ LOG EXT 06 00 01 00 01 00 00 00 00 00 00 40 00 12d+08:18:58.659 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 12d+08:18:58.609 DATA SET MANAGEMENT 06 00 01 00 01 00 00 00 00 00 00 40 00 12d+08:18:58.333 DATA SET MANAGEMENT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 45 --- Current Temperature 0x05 0x010 1 46 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 61 --- Highest Temperature 0x05 0x028 1 28 --- Lowest Temperature 0x05 0x030 1 55 --- Highest Average Short Term Temperature 0x05 0x038 1 55 --- Lowest Average Short Term Temperature 0x05 0x040 1 50 --- Highest Average Long Term Temperature 0x05 0x048 1 50 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 10 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 28 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 24 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error