/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p5 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA MD04ACA400 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: FP2A User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jan 28 13:41:09 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 483) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 6964 4 Start_Stop_Count -O--CK 100 100 000 - 2754 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 041 041 000 - 23976 10 Spin_Retry_Count PO--CK 155 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1578 191 G-Sense_Error_Rate -O--CK 100 100 000 - 176 192 Power-Off_Retract_Count -O--CK 100 100 000 - 488 193 Load_Cycle_Count -O--CK 100 100 000 - 7413 194 Temperature_Celsius -O---K 100 100 000 - 26 (Min/Max 14/61) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 577 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 052 052 000 - 19574 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 301 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 12288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa7 GPL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 577 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 577 [64] occurred at disk power-on lifetime: 18415 hours (767 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 50 02 60 00 00 38 c0 76 a0 e0 00 608 sectors at LBA = 0x38c076a0 = 952137376 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 02 c0 00 00 38 c0 76 40 e0 00 1d+01:03:08.565 WRITE DMA EXT 35 00 00 05 40 00 00 38 c0 71 00 e0 00 1d+01:03:08.560 WRITE DMA EXT 35 00 00 02 c0 00 00 38 c0 6e 40 e0 00 1d+01:03:08.557 WRITE DMA EXT 35 00 00 05 40 00 00 38 c0 69 00 e0 00 1d+01:03:08.552 WRITE DMA EXT 35 00 00 02 c0 00 00 38 c0 66 40 e0 00 1d+01:03:07.509 WRITE DMA EXT Error 576 [63] occurred at disk power-on lifetime: 18415 hours (767 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 e0 00 00 38 c0 0f 20 e0 00 Error: ICRC, ABRT 480 sectors at LBA = 0x38c00f20 = 952110880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 02 c0 00 00 38 c0 0e 40 e0 00 1d+01:03:01.501 WRITE DMA EXT 35 00 00 02 c0 00 00 38 c0 16 40 e0 00 1d+01:03:01.424 WRITE DMA EXT 35 00 00 05 40 00 00 38 c0 11 00 e0 00 1d+01:03:01.419 WRITE DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 00 1d+01:03:01.419 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 1d+01:03:01.419 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 575 [62] occurred at disk power-on lifetime: 18415 hours (767 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 90 00 00 38 c0 0f 70 e0 00 Error: ICRC, ABRT 400 sectors at LBA = 0x38c00f70 = 952110960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 02 c0 00 00 38 c0 0e 40 e0 00 1d+01:03:00.877 WRITE DMA EXT 35 00 00 05 40 00 00 38 c0 09 00 e0 00 1d+01:03:00.872 WRITE DMA EXT 35 00 00 00 08 00 00 d1 00 0c 38 e0 00 1d+01:03:00.233 WRITE DMA EXT 35 00 00 00 08 00 00 d1 00 0b d8 e0 00 1d+01:03:00.233 WRITE DMA EXT 35 00 00 00 08 00 00 d1 00 0b b8 e0 00 1d+01:03:00.233 WRITE DMA EXT Error 574 [61] occurred at disk power-on lifetime: 18415 hours (767 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 f0 00 00 38 80 87 10 e0 00 Error: ICRC, ABRT 496 sectors at LBA = 0x38808710 = 947947280 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 02 c0 00 00 38 80 86 40 e0 00 1d+01:02:50.678 WRITE DMA EXT 35 00 00 05 40 00 00 38 80 81 00 e0 00 1d+01:02:50.673 WRITE DMA EXT 35 00 00 02 c0 00 00 38 80 7e 40 e0 00 1d+01:02:50.670 WRITE DMA EXT 35 00 00 05 40 00 00 38 80 79 00 e0 00 1d+01:02:50.665 WRITE DMA EXT 35 00 00 00 08 00 00 d1 0b f8 00 e0 00 1d+01:02:50.514 WRITE DMA EXT Error 573 [60] occurred at disk power-on lifetime: 18415 hours (767 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 04 e0 00 00 38 80 71 60 e0 00 Error: ICRC, ABRT 1248 sectors at LBA = 0x38807160 = 947941728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 05 40 00 00 38 80 71 00 e0 00 1d+01:02:48.813 WRITE DMA EXT 35 00 00 02 c0 00 00 38 80 6e 40 e0 00 1d+01:02:48.810 WRITE DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 00 1d+01:02:48.810 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 1d+01:02:48.810 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 1d+01:02:48.810 IDENTIFY DEVICE Error 572 [59] occurred at disk power-on lifetime: 18415 hours (767 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 03 c0 00 00 38 80 6a 80 e0 00 Error: ICRC, ABRT 960 sectors at LBA = 0x38806a80 = 947939968 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 05 40 00 00 38 80 69 00 e0 00 1d+01:02:48.265 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+01:02:48.025 FLUSH CACHE EXT ca 00 00 00 10 00 00 00 04 9f 90 e0 00 1d+01:02:48.025 WRITE DMA 35 00 00 02 c0 00 00 38 80 66 40 e0 00 1d+01:02:47.194 WRITE DMA EXT 35 00 00 05 40 00 00 38 80 61 00 e0 00 1d+01:02:47.189 WRITE DMA EXT Error 571 [58] occurred at disk power-on lifetime: 18415 hours (767 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 04 30 00 00 38 40 ea 10 e0 00 Error: ICRC, ABRT 1072 sectors at LBA = 0x3840ea10 = 943778320 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 05 40 00 00 38 40 e9 00 e0 00 1d+01:02:39.053 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+01:02:38.979 FLUSH CACHE EXT 35 00 00 00 08 00 00 e8 c4 94 20 e0 00 1d+01:02:38.979 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+01:02:38.960 FLUSH CACHE EXT 35 00 00 00 38 00 00 e8 c4 93 e8 e0 00 1d+01:02:38.960 WRITE DMA EXT Error 570 [57] occurred at disk power-on lifetime: 18415 hours (767 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 04 80 00 00 38 40 91 c0 e0 00 Error: ICRC, ABRT 1152 sectors at LBA = 0x384091c0 = 943755712 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 05 40 00 00 38 40 91 00 e0 00 1d+01:02:32.054 WRITE DMA EXT 35 00 00 02 c0 00 00 38 40 8e 40 e0 00 1d+01:02:32.051 WRITE DMA EXT 35 00 00 05 40 00 00 38 40 89 00 e0 00 1d+01:02:32.046 WRITE DMA EXT 35 00 00 02 c0 00 00 38 40 86 40 e0 00 1d+01:02:30.999 WRITE DMA EXT 35 00 00 05 40 00 00 38 40 81 00 e0 00 1d+01:02:30.994 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 20/31 Celsius Lifetime Min/Max Temperature: 14/61 Celsius Under/Over Temperature Limit Count: 0/11153 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (226) Index Estimated Time Temperature Celsius 227 2023-01-28 05:44 26 ******* ... ..(199 skipped). .. ******* 427 2023-01-28 09:04 26 ******* 428 2023-01-28 09:05 27 ******** ... ..( 6 skipped). .. ******** 435 2023-01-28 09:12 27 ******** 436 2023-01-28 09:13 28 ********* ... ..( 20 skipped). .. ********* 457 2023-01-28 09:34 28 ********* 458 2023-01-28 09:35 29 ********** ... ..( 20 skipped). .. ********** 1 2023-01-28 09:56 29 ********** 2 2023-01-28 09:57 28 ********* ... ..( 5 skipped). .. ********* 8 2023-01-28 10:03 28 ********* 9 2023-01-28 10:04 27 ******** ... ..( 9 skipped). .. ******** 19 2023-01-28 10:14 27 ******** 20 2023-01-28 10:15 26 ******* ... ..(205 skipped). .. ******* 226 2023-01-28 13:41 26 ******* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 1578 --- Lifetime Power-On Resets 0x01 0x010 4 23976 --- Power-on Hours 0x01 0x018 6 118114251490 --- Logical Sectors Written 0x01 0x020 6 1088267325 --- Number of Write Commands 0x01 0x028 6 242594575003 --- Logical Sectors Read 0x01 0x030 6 1805243106 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 176 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 23534 --- Spindle Motor Power-on Hours 0x03 0x010 4 19574 --- Head Flying Hours 0x03 0x018 4 7413 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 122 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 26 --- Current Temperature 0x05 0x010 1 28 N-- Average Short Term Temperature 0x05 0x018 1 42 N-- Average Long Term Temperature 0x05 0x020 1 61 --- Highest Temperature 0x05 0x028 1 14 --- Lowest Temperature 0x05 0x030 1 57 N-- Highest Average Short Term Temperature 0x05 0x038 1 19 N-- Lowest Average Short Term Temperature 0x05 0x040 1 48 N-- Highest Average Long Term Temperature 0x05 0x048 1 22 N-- Lowest Average Long Term Temperature 0x05 0x050 4 18254 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 7932 --- Number of Hardware Resets 0x06 0x018 4 577 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 24 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 23 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC