/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.2 Device Model: ST98823AS Serial Number: -- Firmware Version: 7.24 User Capacity: 80,026,361,856 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5528 ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Thu Feb 29 14:54:21 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 426) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 47) minutes. SCT capabilities: (0x0001) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 100 006 - 71222473 3 Spin_Up_Time -O---- 095 095 000 - 0 4 Start_Stop_Count PO--CK 095 095 020 - 6113 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 081 060 030 - 149507174 9 Power_On_Hours -O--CK 090 090 000 - 8867 10 Spin_Retry_Count PO--C- 100 100 034 - 0 12 Power_Cycle_Count PO--CK 097 097 020 - 3524 187 Reported_Uncorrect -O--CK 080 080 000 - 20 189 High_Fly_Writes -O-RCK 070 070 000 - 30 190 Airflow_Temperature_Cel -O---K 074 050 045 - 26 (Min/Max 22/27) 192 Power-Off_Retract_Count -O--CK 100 100 000 - 155 193 Load_Cycle_Count -O--CK 001 001 000 - 211300 194 Temperature_Celsius -O---K 026 050 000 - 26 (0 10 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 093 050 000 - 188030819 197 Current_Pending_Sector -O--C- 100 100 000 - 3 198 Offline_Uncorrectable ----C- 100 100 000 - 3 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 SL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 SL R/O 1 NCQ Command Error log 0x11 SL R/O 1 SATA Phy Event Counters log 0x20 SL R/O 1 Streaming performance log 0x21 SL R/O 1 Write stream error log 0x22 SL R/O 1 Read stream error log 0x23 SL R/O 1 Delayed sector log 0x80-0x9f SL R/W 16 Host vendor specific log 0xa0 SL VS 1 Device vendor specific log 0xa1 SL VS 20 Device vendor specific log 0xa2 SL VS 101 Device vendor specific log 0xa8 SL VS 20 Device vendor specific log 0xa9 SL VS 1 Device vendor specific log 0xe0 SL R/W 1 SCT Command/Status 0xe1 SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 20 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 20 occurred at disk power-on lifetime: 8835 hours (368 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 7d 96 8a e3 Error: UNC at LBA = 0x038a967d = 59414141 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 d0 10 77 96 8a e3 00 05:42:47.163 READ DMA c8 d0 80 5f 97 8a e3 00 05:42:44.857 READ DMA c8 d0 10 77 96 8a e3 00 05:42:44.857 READ DMA c8 d0 01 00 00 00 e0 00 05:42:44.855 READ DMA c8 d0 80 df 96 8a e3 00 05:42:44.855 READ DMA Error 19 occurred at disk power-on lifetime: 8835 hours (368 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 7d 96 8a e3 Error: UNC at LBA = 0x038a967d = 59414141 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 d0 10 77 96 8a e3 00 05:42:38.122 READ DMA c8 d0 01 00 00 00 e0 00 05:42:44.857 READ DMA c8 d0 80 df 96 8a e3 00 05:42:44.857 READ DMA ca d0 08 e7 d7 17 e0 00 05:42:44.855 WRITE DMA c8 d0 01 00 00 00 e0 00 05:42:44.855 READ DMA Error 18 occurred at disk power-on lifetime: 8835 hours (368 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 7f 96 8a e3 Error: UNC at LBA = 0x038a967f = 59414143 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 d0 60 7f 96 8a e3 00 05:42:38.122 READ DMA ca d0 10 ff f2 17 e0 00 05:42:33.679 WRITE DMA c8 d0 68 77 96 8a e3 00 05:42:33.666 READ DMA c8 d0 08 6f 96 8a e3 00 05:42:33.666 READ DMA ca d0 08 df d7 17 e0 00 05:42:33.656 WRITE DMA Error 17 occurred at disk power-on lifetime: 8835 hours (368 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 7d 96 8a e3 Error: UNC at LBA = 0x038a967d = 59414141 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 d0 68 77 96 8a e3 00 05:42:38.122 READ DMA c8 d0 08 6f 96 8a e3 00 05:42:33.679 READ DMA ca d0 08 df d7 17 e0 00 05:42:33.666 WRITE DMA c8 d0 01 00 00 00 e0 00 05:42:33.666 READ DMA ca d0 08 ef d7 17 e0 00 05:42:33.656 WRITE DMA Error 16 occurred at disk power-on lifetime: 8835 hours (368 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 7d 96 8a e3 Error: UNC at LBA = 0x038a967d = 59414141 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 d0 70 6f 96 8a e3 00 05:42:24.725 READ DMA c8 d0 08 67 96 8a e3 00 05:42:33.679 READ DMA ca d0 18 e7 f2 17 e0 00 05:42:33.666 WRITE DMA c8 d0 01 00 00 00 e0 00 05:42:33.666 READ DMA c8 d0 78 67 96 8a e3 00 05:42:33.656 READ DMA SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3 - # 2 Short offline Completed without error 00% 3 - # 3 Short offline Completed without error 00% 3 - # 4 Short offline Completed without error 00% 3 - # 5 Short offline Completed without error 00% 3 - # 6 Short offline Completed without error 00% 3 - # 7 Short offline Completed without error 00% 3 - # 8 Short offline Completed without error 00% 2 - # 9 Short offline Completed without error 00% 2 - #10 Short offline Completed without error 00% 2 - #11 Short offline Completed without error 00% 2 - #12 Short offline Completed without error 00% 2 - #13 Short offline Completed without error 00% 2 - #14 Short offline Completed without error 00% 1 - #15 Short offline Completed without error 00% 1 - #16 Short offline Completed without error 00% 1 - #17 Short offline Completed without error 00% 1 - #18 Short offline Completed without error 00% 1 - #19 Short offline Completed without error 00% 1 - #20 Short offline Completed without error 00% 0 - #21 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 521 (0x0209) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: --/ 0 Celsius Lifetime Min/Max Temperature: --/ 0 Celsius SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 14 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/nvd0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: GV128 Serial Number: -- Firmware Version: T1103F0L PCI Vendor/Subsystem ID: 0x126f IEEE OUI Identifier: 0x000001 Total NVM Capacity: 128,035,676,160 [128 GB] Unallocated NVM Capacity: 0 Controller ID: 1 NVMe Version: 1.3 Number of Namespaces: 1 Namespace 1 Size/Capacity: 128,035,676,160 [128 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 000001 ... Local Time is: Thu Feb 29 14:54:22 2024 CET Firmware Updates (0x12): 1 Slot, no Reset required Optional Admin Commands (0x0007): Security Format Frmw_DL Optional NVM Commands (0x0014): DS_Mngmt Sav/Sel_Feat Log Page Attributes (0x03): S/H_per_NS Cmd_Eff_Lg Maximum Data Transfer Size: 64 Pages Warning Comp. Temp. Threshold: 83 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 6.00W - - 0 0 0 0 0 0 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 40 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 3% Data Units Read: 240,204 [122 GB] Data Units Written: 16,003,459 [8.19 TB] Host Read Commands: 5,777,708 Host Write Commands: 214,012,602 Controller Busy Time: 40,583 Power Cycles: 30 Power On Hours: 8,815 Unsafe Shutdowns: 10 Media and Data Integrity Errors: 0 Error Information Log Entries: 0 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Error Information (NVMe Log 0x01, 16 of 64 entries) No Errors Logged Self-tests not supported