/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE-p6 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD2500BEVT-35A23T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Nov 20 08:54:32 2024 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6360) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 77) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 17 3 Spin_Up_Time POS--K 149 147 021 - 1550 4 Start_Stop_Count -O--CK 097 097 000 - 3979 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 094 094 000 - 5085 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3862 192 Power-Off_Retract_Count -O--CK 200 200 000 - 486 193 Load_Cycle_Count -O--CK 067 067 000 - 399964 194 Temperature_Celsius -O---K 107 084 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 2641 hours (110 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 30 2a 02 40 00 Error: UNC at LBA = 0x00302a02 = 3156482 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 70 00 08 00 00 04 ac 67 c8 40 00 00:01:28.900 READ FPDMA QUEUED 60 00 80 00 00 00 00 00 30 29 e0 40 00 00:01:28.885 READ FPDMA QUEUED 60 00 10 00 00 00 00 04 ac 02 60 40 00 00:01:28.815 READ FPDMA QUEUED 61 01 00 00 58 00 00 04 c0 76 a0 40 00 00:01:28.764 WRITE FPDMA QUEUED 61 01 00 00 50 00 00 04 c0 75 a0 40 00 00:01:28.764 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 2641 hours (110 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 30 29 60 40 00 Error: UNC at LBA = 0x00302960 = 3156320 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 10 00 00 04 bd b7 d8 40 00 00:01:26.289 READ FPDMA QUEUED 60 00 08 00 10 00 00 04 ac 02 58 40 00 00:01:26.282 READ FPDMA QUEUED 60 00 08 00 08 00 00 04 c0 df c8 40 00 00:01:26.269 READ FPDMA QUEUED 60 00 80 00 00 00 00 00 30 29 60 40 00 00:01:26.269 READ FPDMA QUEUED 60 00 10 00 00 00 00 04 ac 02 88 40 00 00:01:26.229 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 2641 hours (110 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 30 28 e0 40 00 Error: UNC at LBA = 0x003028e0 = 3156192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 10 00 00 00 30 28 e0 40 00 00:01:23.360 READ FPDMA QUEUED 60 00 08 00 08 00 00 00 6c 92 58 40 00 00:01:23.360 READ FPDMA QUEUED b0 00 d0 00 00 00 00 01 c2 4f 00 61 00 00:01:23.326 SMART READ DATA 60 00 08 00 08 00 00 00 6b bf c0 40 00 00:01:23.325 READ FPDMA QUEUED b0 00 da 00 00 00 00 00 c2 4f 00 40 00 00:01:23.178 SMART RETURN STATUS Error 3 [2] occurred at disk power-on lifetime: 2641 hours (110 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 30 28 60 40 00 Error: UNC at LBA = 0x00302860 = 3156064 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 28 00 00 00 30 28 60 40 00 00:01:20.373 READ FPDMA QUEUED 60 00 08 00 20 00 00 04 bd b4 58 40 00 00:01:20.373 READ FPDMA QUEUED 60 00 08 00 18 00 00 00 6b 6a 48 40 00 00:01:20.373 READ FPDMA QUEUED 60 00 08 00 10 00 00 04 be a4 28 40 00 00:01:20.373 READ FPDMA QUEUED 60 00 08 00 08 00 00 00 0b 0b 78 40 00 00:01:20.373 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 2641 hours (110 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 30 27 e0 40 00 Error: UNC at LBA = 0x003027e0 = 3155936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 10 00 00 00 25 a3 82 40 00 00:01:17.364 READ FPDMA QUEUED 60 00 10 00 08 00 00 00 25 a2 1a 40 00 00:01:17.364 READ FPDMA QUEUED 60 00 11 00 10 00 00 00 0b 03 d8 40 00 00:01:17.347 READ FPDMA QUEUED 60 00 08 00 08 00 00 00 0d f3 40 40 00 00:01:17.347 READ FPDMA QUEUED 60 00 80 00 00 00 00 00 30 27 e0 40 00 00:01:17.344 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 2641 hours (110 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 30 27 9c 40 00 Error: UNC at LBA = 0x0030279c = 3155868 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 00 30 27 60 40 00 00:01:12.892 READ FPDMA QUEUED 60 00 6d 00 00 00 00 01 4a 54 60 40 00 00:01:12.891 READ FPDMA QUEUED 60 00 f8 00 00 00 00 01 4a 53 68 40 00 00:01:12.839 READ FPDMA QUEUED 60 00 08 00 00 00 00 01 4a 53 60 40 00 00:01:12.831 READ FPDMA QUEUED 60 00 40 00 00 00 00 00 39 4f b8 40 00 00:01:12.829 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3282 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 35/43 Celsius Lifetime Min/Max Temperature: ?/60 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (58) Index Estimated Time Temperature Celsius 59 2024-11-20 06:47 36 ***************** 60 2024-11-20 06:48 37 ****************** 61 2024-11-20 06:49 36 ***************** ... ..( 28 skipped). .. ***************** 90 2024-11-20 07:18 36 ***************** 91 2024-11-20 07:19 37 ****************** 92 2024-11-20 07:20 37 ****************** 93 2024-11-20 07:21 36 ***************** ... ..( 2 skipped). .. ***************** 96 2024-11-20 07:24 36 ***************** 97 2024-11-20 07:25 37 ****************** 98 2024-11-20 07:26 37 ****************** 99 2024-11-20 07:27 36 ***************** 100 2024-11-20 07:28 36 ***************** 101 2024-11-20 07:29 36 ***************** 102 2024-11-20 07:30 37 ****************** 103 2024-11-20 07:31 36 ***************** ... ..( 82 skipped). .. ***************** 58 2024-11-20 08:54 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 543865 Vendor specific