/dev/ada0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.1-RELEASE-p18-HBSD amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7 Device Model: SAMSUNG HM320II Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AC101C4 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Jun 17 14:50:34 2021 -08 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6240) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 104) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 9 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 086 077 025 - 4350 4 Start_Stop_Count -O--CK 099 099 000 - 1239 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 4597 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 095 095 000 - 5052 12 Power_Cycle_Count -O--CK 099 099 000 - 1545 191 G-Sense_Error_Rate -O---K 100 100 000 - 684 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 039 000 - 30 (Min/Max 9/62) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 31 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 1406 223 Load_Retry_Count -O--CK 095 095 000 - 5052 225 Load_Cycle_Count -O--CK 001 001 000 - 5405418 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xbb GPL VS 4 Device vendor specific log 0xbc GPL VS 2 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 31 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 31 [6] occurred at disk power-on lifetime: 4096 hours (170 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 16 cf 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 40 00 00 1d e2 16 cf 40 00 00:00:00.232 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 1d e2 b3 8f 40 00 00:00:00.232 WRITE FPDMA QUEUED 61 00 00 00 40 00 00 1d e2 16 cf 40 00 00:00:00.232 WRITE FPDMA QUEUED 61 00 00 00 40 00 00 1d e2 16 cf 40 00 00:00:00.232 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 08 f2 a9 97 40 00 00:00:00.232 WRITE FPDMA QUEUED Error 30 [5] occurred at disk power-on lifetime: 4096 hours (170 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 16 cf 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 40 00 00 1d e2 16 cf 40 00 00:00:00.201 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 00 00 cf 40 00 00:00:00.201 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 00 00 9e 4f 40 00 00:00:00.201 WRITE FPDMA QUEUED 61 00 00 00 40 00 00 1d e2 16 cf 40 00 00:00:00.201 WRITE FPDMA QUEUED 35 00 00 00 08 00 00 1d e2 b3 8f 40 08 00:00:00.201 WRITE DMA EXT Error 29 [4] occurred at disk power-on lifetime: 4096 hours (170 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 16 cf 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 40 00 00 1d e2 16 cf 40 00 00:00:00.171 WRITE FPDMA QUEUED 61 00 00 00 40 00 00 1d e2 16 cf 40 00 00:00:00.171 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 1d e2 b3 8f 40 00 00:00:00.171 WRITE FPDMA QUEUED 61 00 00 00 40 00 00 1d e2 16 cf 40 00 00:00:00.171 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 00:00:00.171 SET FEATURES [Enable write cache] Error 28 [3] occurred at disk power-on lifetime: 4095 hours (170 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 02 cf 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 40 00 00 14 dd 5e 0f 40 00 00:00:00.467 WRITE FPDMA QUEUED 61 00 aa 00 40 00 00 14 df 0e cf 40 08 00:00:00.467 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 14 df 0d 0f 40 00 00:00:00.467 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 14 df 0c 0f 40 00 00:00:00.467 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 14 df 0a 4f 40 00 00:00:00.467 WRITE FPDMA QUEUED Error 27 [2] occurred at disk power-on lifetime: 4095 hours (170 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 c7 4f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 aa 00 80 00 00 08 f3 5b 0f 40 08 00:00:01.274 WRITE FPDMA QUEUED 60 00 02 00 08 00 00 14 cc d2 47 40 00 00:00:01.274 READ FPDMA QUEUED 61 00 aa 01 00 00 00 14 cc 96 0f 40 00 00:00:01.274 WRITE FPDMA QUEUED 61 00 00 00 c0 00 00 14 cb dd cf 40 00 00:00:01.274 WRITE FPDMA QUEUED 61 00 10 01 00 00 00 14 cb dc 8f 40 00 00:00:01.274 WRITE FPDMA QUEUED Error 26 [1] occurred at disk power-on lifetime: 4095 hours (170 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 c7 4f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 01 00 00 00 14 cb c7 4f 40 00 00:00:01.274 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 00:00:01.274 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 40 00 00:00:01.274 SET FEATURES [Enable read look-ahead] c6 00 00 00 10 00 00 00 00 00 00 40 00 00:00:01.274 SET MULTIPLE MODE ef 00 10 00 02 00 00 00 00 00 00 40 00 00:00:01.274 SET FEATURES [Enable SATA feature] Error 25 [0] occurred at disk power-on lifetime: 4095 hours (170 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 c7 4f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 01 00 00 00 14 cb c7 4f 40 00 00:00:01.274 WRITE FPDMA QUEUED 60 00 10 00 08 00 00 14 cc c5 c7 40 00 00:00:01.274 READ FPDMA QUEUED 61 00 03 01 00 00 00 14 cb c6 0f 40 00 00:00:01.274 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 00:00:01.274 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 40 00 00:00:01.274 SET FEATURES [Enable read look-ahead] Error 24 [7] occurred at disk power-on lifetime: 4095 hours (170 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 b7 0f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 02 01 00 00 00 09 06 b7 0f 40 00 00:00:01.244 WRITE FPDMA QUEUED 61 00 02 01 00 00 00 09 06 b6 0f 40 00 00:00:01.244 WRITE FPDMA QUEUED 61 00 aa 01 00 00 00 09 06 b5 0f 40 00 00:00:01.244 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 09 06 b4 0f 40 00 00:00:01.244 WRITE FPDMA QUEUED 61 00 10 01 00 00 00 09 06 b3 0f 40 00 00:00:01.244 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 27/32 Celsius Lifetime Min/Max Temperature: 12/62 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (114) Index Estimated Time Temperature Celsius 115 2021-06-17 04:15 31 ************ ... ..( 11 skipped). .. ************ 127 2021-06-17 05:15 31 ************ 0 2021-06-17 05:20 32 ************* 1 2021-06-17 05:25 31 ************ 2 2021-06-17 05:30 30 *********** 3 2021-06-17 05:35 30 *********** 4 2021-06-17 05:40 29 ********** 5 2021-06-17 05:45 29 ********** 6 2021-06-17 05:50 29 ********** 7 2021-06-17 05:55 28 ********* ... ..( 3 skipped). .. ********* 11 2021-06-17 06:15 28 ********* 12 2021-06-17 06:20 27 ******** ... ..( 7 skipped). .. ******** 20 2021-06-17 07:00 27 ******** 21 2021-06-17 07:05 28 ********* 22 2021-06-17 07:10 27 ******** 23 2021-06-17 07:15 28 ********* 24 2021-06-17 07:20 28 ********* 25 2021-06-17 07:25 27 ******** 26 2021-06-17 07:30 27 ******** 27 2021-06-17 07:35 28 ********* 28 2021-06-17 07:40 28 ********* 29 2021-06-17 07:45 28 ********* 30 2021-06-17 07:50 29 ********** ... ..( 23 skipped). .. ********** 54 2021-06-17 09:50 29 ********** 55 2021-06-17 09:55 30 *********** ... ..( 58 skipped). .. *********** 114 2021-06-17 14:50 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 34 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 34 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific