/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green Device Model: WDC WD5000AAVS-00ZTB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01B01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sun Jun 25 21:52:49 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13980) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 163) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 2 3 Spin_Up_Time PO---- 167 158 021 - 4650 4 Start_Stop_Count -O--CK 097 097 000 - 3363 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 075 075 000 - 18927 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3266 192 Power-Off_Retract_Count -O--CK 200 200 000 - 105 193 Load_Cycle_Count -O--CK 001 001 000 - 1359885 194 Temperature_Celsius -O---K 108 095 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 900 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 900 [11] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 01 08 00 00 51 40 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 5d 25 00 3b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 5c 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] 00 59 25 00 3b 00 00 08 00 00 00 00 00 00:00:15.194 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 08 00 3b 58 25 00 00 00 00 00:00:32.776 NOP [Abort queued commands] Error 899 [10] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 00 08 00 00 51 40 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 5c 25 00 3b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 5a 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] 00 58 25 00 3b 00 80 08 00 00 00 00 00 00:00:15.193 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 56 25 00 00 00 00 00:00:02.056 NOP [Abort queued commands] Error 898 [9] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 00 08 00 00 51 40 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 5a 25 00 3b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 80 00 3b 59 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] 00 56 25 00 3b 00 08 08 00 00 00 00 00 00:00:15.192 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 55 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] Error 897 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 01 08 00 00 51 40 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 59 25 00 3b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 08 00 3b 58 25 00 00 00 00 00:00:32.776 NOP [Abort queued commands] 00 55 25 00 3b 00 00 08 00 00 00 00 00 00:00:15.190 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 53 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] Error 896 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 01 08 00 00 51 40 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 58 25 00 3b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 56 25 00 00 00 00 00:00:02.056 NOP [Abort queued commands] 00 53 25 00 3b 00 00 08 00 00 00 00 00 00:00:15.189 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 52 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] Error 895 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 00 08 00 00 51 40 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 56 25 00 3b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 55 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] 00 52 25 00 3b 00 00 08 00 00 00 00 00 00:00:15.187 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 51 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] Error 894 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 00 08 00 00 51 40 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 55 25 00 3b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 53 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] 00 51 25 00 3b 00 00 08 00 00 00 00 00 00:00:15.186 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 4f 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] Error 893 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 00 08 00 00 51 40 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 53 25 00 3b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 00 00 3b 52 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] 00 4f 25 00 3b 00 00 08 00 00 00 00 00 00:00:15.185 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 10 00 3b 4e 25 00 00 00 00 00:00:00.008 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 9950 - # 2 Short offline Completed without error 00% 5740 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 38/41 Celsius Lifetime Min/Max Temperature: 38/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/85 Celsius Temperature History Size (Index): 128 (72) Index Estimated Time Temperature Celsius 73 2023-06-25 19:45 41 ********************** ... ..( 24 skipped). .. ********************** 98 2023-06-25 20:10 41 ********************** 99 2023-06-25 20:11 42 *********************** ... ..( 2 skipped). .. *********************** 102 2023-06-25 20:14 42 *********************** 103 2023-06-25 20:15 41 ********************** ... ..( 30 skipped). .. ********************** 6 2023-06-25 20:46 41 ********************** 7 2023-06-25 20:47 42 *********************** ... ..( 29 skipped). .. *********************** 37 2023-06-25 21:17 42 *********************** 38 2023-06-25 21:18 41 ********************** 39 2023-06-25 21:19 41 ********************** 40 2023-06-25 21:20 42 *********************** 41 2023-06-25 21:21 41 ********************** 42 2023-06-25 21:22 41 ********************** 43 2023-06-25 21:23 40 ********************* 44 2023-06-25 21:24 40 ********************* 45 2023-06-25 21:25 40 ********************* 46 2023-06-25 21:26 41 ********************** 47 2023-06-25 21:27 40 ********************* ... ..( 2 skipped). .. ********************* 50 2023-06-25 21:30 40 ********************* 51 2023-06-25 21:31 ? - 52 2023-06-25 21:32 41 ********************** 53 2023-06-25 21:33 41 ********************** 54 2023-06-25 21:34 40 ********************* ... ..( 2 skipped). .. ********************* 57 2023-06-25 21:37 40 ********************* 58 2023-06-25 21:38 39 ******************** 59 2023-06-25 21:39 39 ******************** 60 2023-06-25 21:40 39 ******************** 61 2023-06-25 21:41 40 ********************* ... ..( 2 skipped). .. ********************* 64 2023-06-25 21:44 40 ********************* 65 2023-06-25 21:45 39 ******************** 66 2023-06-25 21:46 39 ******************** 67 2023-06-25 21:47 38 ******************* 68 2023-06-25 21:48 38 ******************* 69 2023-06-25 21:49 39 ******************** 70 2023-06-25 21:50 39 ******************** 71 2023-06-25 21:51 40 ********************* 72 2023-06-25 21:52 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x8000 4 1253 Vendor specific