/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p7 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7E (AF) Device Model: SAMSUNG HM321HI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AJ10002 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon May 27 14:49:09 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4620) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 77) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 3 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 089 089 025 - 3412 4 Start_Stop_Count -O--CK 001 001 000 - 148690 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 30593 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 526 12 Power_Cycle_Count -O--CK 098 098 000 - 2759 191 G-Sense_Error_Rate -O---K 099 099 000 - 15942 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 061 050 000 - 39 (Min/Max 7/50) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 149 223 Load_Retry_Count -O--CK 100 100 000 - 526 225 Load_Cycle_Count -O--CK 055 055 000 - 457117 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 23/40 Celsius Lifetime Min/Max Temperature: 9/66 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (9) Index Estimated Time Temperature Celsius 10 2024-05-27 04:10 39 ******************** 11 2024-05-27 04:15 37 ****************** ... ..( 69 skipped). .. ****************** 81 2024-05-27 10:05 37 ****************** 82 2024-05-27 10:10 36 ***************** 83 2024-05-27 10:15 37 ****************** ... ..( 33 skipped). .. ****************** 117 2024-05-27 13:05 37 ****************** 118 2024-05-27 13:10 38 ******************* ... ..( 8 skipped). .. ******************* 127 2024-05-27 13:55 38 ******************* 0 2024-05-27 14:00 39 ******************** 1 2024-05-27 14:05 39 ******************** 2 2024-05-27 14:10 38 ******************* 3 2024-05-27 14:15 39 ******************** ... ..( 5 skipped). .. ******************** 9 2024-05-27 14:45 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 8 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 7 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/ada1 smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p7 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA MQ01ACF032 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: AV002E User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: Not in smartctl database 7.3/5528 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 27 14:49:09 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 72) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 1942 4 Start_Stop_Count -O--CK 100 100 000 - 18089 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 038 038 000 - 24825 10 Spin_Retry_Count PO--CK 253 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1109 191 G-Sense_Error_Rate -O--CK 100 100 000 - 919 192 Power-Off_Retract_Count -O--CK 100 100 000 - 98 193 Load_Cycle_Count -O--CK 092 092 000 - 82135 194 Temperature_Celsius -O---K 100 100 000 - 39 (Min/Max 16/46) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 030 030 000 - 28102 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 256 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 150 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 150 [149] occurred at disk power-on lifetime: 749 hours (31 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 0f ff 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:08.805 SECURITY UNLOCK c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:08.795 SET MULTIPLE MODE c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:08.795 SET MULTIPLE MODE 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:08.794 INITIALIZE DEVICE PARAMETERS [OBS-6] 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:08.793 INITIALIZE DEVICE PARAMETERS [OBS-6] Error 149 [148] occurred at disk power-on lifetime: 745 hours (31 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 0f ff 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:16.380 SECURITY UNLOCK c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:16.371 SET MULTIPLE MODE 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:16.371 INITIALIZE DEVICE PARAMETERS [OBS-6] ef 00 03 00 45 00 00 00 00 00 00 e0 00 00:00:16.371 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 e0 00 00:00:16.369 SET FEATURES [Set transfer mode] Error 148 [147] occurred at disk power-on lifetime: 741 hours (30 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 0f ff 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:08.433 SECURITY UNLOCK c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:08.424 SET MULTIPLE MODE 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:08.423 INITIALIZE DEVICE PARAMETERS [OBS-6] 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:08.422 INITIALIZE DEVICE PARAMETERS [OBS-6] ef 00 03 00 45 00 00 00 00 00 00 e0 00 00:00:08.422 SET FEATURES [Set transfer mode] Error 147 [146] occurred at disk power-on lifetime: 737 hours (30 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 0f ff 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:08.875 SECURITY UNLOCK c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:08.867 SET MULTIPLE MODE 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:08.867 INITIALIZE DEVICE PARAMETERS [OBS-6] ef 00 03 00 45 00 00 00 00 00 00 e0 00 00:00:08.866 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 e0 00 00:00:08.865 SET FEATURES [Set transfer mode] Error 146 [145] occurred at disk power-on lifetime: 733 hours (30 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 0f ff 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:08.221 SECURITY UNLOCK c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:08.213 SET MULTIPLE MODE 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:08.213 INITIALIZE DEVICE PARAMETERS [OBS-6] ef 00 03 00 45 00 00 00 00 00 00 e0 00 00:00:08.212 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 e0 00 00:00:08.212 SET FEATURES [Set transfer mode] Error 145 [144] occurred at disk power-on lifetime: 725 hours (30 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 0f ff 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:20.952 SECURITY UNLOCK c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:20.943 SET MULTIPLE MODE 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:20.943 INITIALIZE DEVICE PARAMETERS [OBS-6] ef 00 03 00 45 00 00 00 00 00 00 e0 00 00:00:20.942 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 e0 00 00:00:20.941 SET FEATURES [Set transfer mode] Error 144 [143] occurred at disk power-on lifetime: 720 hours (30 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 0f ff 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:13.869 SECURITY UNLOCK c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:13.860 SET MULTIPLE MODE c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:13.859 SET MULTIPLE MODE 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:13.858 INITIALIZE DEVICE PARAMETERS [OBS-6] 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:13.858 INITIALIZE DEVICE PARAMETERS [OBS-6] Error 143 [142] occurred at disk power-on lifetime: 712 hours (29 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 0f ff 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:10.173 SECURITY UNLOCK c6 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:10.164 SET MULTIPLE MODE 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:10.163 INITIALIZE DEVICE PARAMETERS [OBS-6] 91 00 00 00 3f 00 00 00 00 00 00 ef 00 00:00:10.163 INITIALIZE DEVICE PARAMETERS [OBS-6] ef 00 03 00 45 00 00 00 00 00 00 e0 00 00:00:10.162 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 24/40 Celsius Lifetime Min/Max Temperature: 16/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (130) Index Estimated Time Temperature Celsius 131 2024-05-27 06:52 37 ****************** ... ..( 8 skipped). .. ****************** 140 2024-05-27 07:01 37 ****************** 141 2024-05-27 07:02 38 ******************* 142 2024-05-27 07:03 37 ****************** 143 2024-05-27 07:04 38 ******************* 144 2024-05-27 07:05 37 ****************** 145 2024-05-27 07:06 37 ****************** 146 2024-05-27 07:07 38 ******************* ... ..( 12 skipped). .. ******************* 159 2024-05-27 07:20 38 ******************* 160 2024-05-27 07:21 37 ****************** ... ..( 3 skipped). .. ****************** 164 2024-05-27 07:25 37 ****************** 165 2024-05-27 07:26 38 ******************* 166 2024-05-27 07:27 37 ****************** 167 2024-05-27 07:28 37 ****************** 168 2024-05-27 07:29 37 ****************** 169 2024-05-27 07:30 38 ******************* ... ..( 21 skipped). .. ******************* 191 2024-05-27 07:52 38 ******************* 192 2024-05-27 07:53 37 ****************** 193 2024-05-27 07:54 37 ****************** 194 2024-05-27 07:55 38 ******************* 195 2024-05-27 07:56 37 ****************** ... ..(248 skipped). .. ****************** 444 2024-05-27 12:05 37 ****************** 445 2024-05-27 12:06 38 ******************* 446 2024-05-27 12:07 37 ****************** 447 2024-05-27 12:08 37 ****************** 448 2024-05-27 12:09 38 ******************* 449 2024-05-27 12:10 37 ****************** 450 2024-05-27 12:11 38 ******************* 451 2024-05-27 12:12 38 ******************* 452 2024-05-27 12:13 38 ******************* 453 2024-05-27 12:14 37 ****************** ... ..( 4 skipped). .. ****************** 458 2024-05-27 12:19 37 ****************** 459 2024-05-27 12:20 38 ******************* 460 2024-05-27 12:21 37 ****************** 461 2024-05-27 12:22 38 ******************* 462 2024-05-27 12:23 37 ****************** 463 2024-05-27 12:24 38 ******************* ... ..( 73 skipped). .. ******************* 59 2024-05-27 13:38 38 ******************* 60 2024-05-27 13:39 39 ******************** ... ..( 69 skipped). .. ******************** 130 2024-05-27 14:49 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 1109 --- Lifetime Power-On Resets 0x01 0x010 4 24825 --- Power-on Hours 0x01 0x018 6 64868117348 --- Logical Sectors Written 0x01 0x020 6 1864897320 --- Number of Write Commands 0x01 0x028 6 21112032459 --- Logical Sectors Read 0x01 0x030 6 364664205 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 919 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 24820 --- Spindle Motor Power-on Hours 0x03 0x010 4 28102 --- Head Flying Hours 0x03 0x018 4 82135 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 36 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 39 --- Current Temperature 0x05 0x010 1 38 N-- Average Short Term Temperature 0x05 0x018 1 35 N-- Average Long Term Temperature 0x05 0x020 1 46 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 43 N-- Highest Average Short Term Temperature 0x05 0x038 1 24 N-- Lowest Average Short Term Temperature 0x05 0x040 1 40 N-- Highest Average Long Term Temperature 0x05 0x048 1 29 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 22210 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 41 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 8 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 8 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC