/dev/ada0 smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar 7K750 Device Model: Hitachi HTS727550A9E364 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JF3OA0E0 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Mar 16 15:37:17 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 116) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 099 062 - 0 2 Throughput_Performance P-S--K 100 100 040 - 0 3 Spin_Up_Time PO---K 205 100 033 - 2 4 Start_Stop_Count -O--CK 094 094 000 - 10138 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 8 (0 1) 7 Seek_Error_Rate POSR-K 100 098 067 - 0 8 Seek_Time_Performance P-S--K 100 100 040 - 0 9 Power_On_Hours -O--CK 039 039 000 - 26727 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 6777 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 099 000 - 1318787219457 188 Command_Timeout -O--CK 100 099 000 - 34365571175 190 Airflow_Temperature_Cel -O---K 064 043 045 Past 36 (Min/Max 18/36) 191 G-Sense_Error_Rate -O--CK 054 054 000 - 11973 192 Power-Off_Retract_Count -O--CK 097 097 000 - 46858955 193 Load_Cycle_Count -O--CK 074 074 000 - 260926 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 30 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 30 [1] occurred at disk power-on lifetime: 26606 hours (1108 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 0a cb 70 2d 0a 00 Error: WP at LBA = 0x0acb702d = 181104685 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 02 a0 00 70 00 00 22 5f 0b 25 40 00 00:05:47.626 WRITE FPDMA QUEUED 61 02 a0 00 68 00 00 22 5f 08 85 40 00 00:05:47.623 WRITE FPDMA QUEUED 61 02 a0 00 60 00 00 22 5f 05 e5 40 00 00:05:47.620 WRITE FPDMA QUEUED 61 02 a0 00 58 00 00 22 5f 03 45 40 00 00:05:47.615 WRITE FPDMA QUEUED 61 02 a0 00 50 00 00 22 5f 00 a5 40 00 00:05:47.612 WRITE FPDMA QUEUED Error 29 [0] occurred at disk power-on lifetime: 26588 hours (1107 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 00 01 c1 00 00 00 Error: WP at LBA = 0x0001c100 = 114944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 06 68 00 48 00 00 11 44 b0 28 40 00 00:07:02.138 WRITE FPDMA QUEUED 61 02 48 00 40 00 00 11 44 ad e0 40 00 00:07:02.136 WRITE FPDMA QUEUED 61 06 c8 00 30 00 00 11 44 a7 18 40 00 00:07:02.128 WRITE FPDMA QUEUED 61 04 98 00 28 00 00 11 44 a2 80 40 00 00:07:02.125 WRITE FPDMA QUEUED 61 0a 00 00 20 00 00 11 44 98 80 40 00 00:07:02.100 WRITE FPDMA QUEUED Error 28 [3] occurred at disk power-on lifetime: 26414 hours (1100 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 00 10 fc c0 00 00 Error: WP at LBA = 0x0010fcc0 = 1113280 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 0a 00 00 38 00 00 11 44 83 e8 40 00 00:05:54.177 WRITE FPDMA QUEUED 61 0a 00 00 30 00 00 11 44 79 e8 40 00 00:05:54.159 WRITE FPDMA QUEUED 61 0a 00 00 28 00 00 11 44 6f e8 40 00 00:05:54.139 WRITE FPDMA QUEUED 61 0a 00 00 20 00 00 11 44 65 e8 40 00 00:05:54.121 WRITE FPDMA QUEUED 61 0a 00 00 18 00 00 11 44 5b e8 40 00 00:05:54.103 WRITE FPDMA QUEUED Error 27 [2] occurred at disk power-on lifetime: 21973 hours (915 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 00 00 00 24 04 99 98 04 00 Error: IDNF at LBA = 0x24049998 = 604281240 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 20 00 a0 00 00 39 58 e0 00 40 00 03:35:38.305 WRITE FPDMA QUEUED 61 00 08 00 98 00 00 2d be 42 28 40 00 03:35:36.306 WRITE FPDMA QUEUED 61 00 08 00 90 00 00 2d bc e0 d0 40 00 03:35:35.104 WRITE FPDMA QUEUED 61 00 08 00 88 00 00 39 7e 01 50 40 00 03:35:34.346 WRITE FPDMA QUEUED 61 00 08 00 80 00 00 34 50 96 d8 40 00 03:35:34.345 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 26651 - # 2 Short offline Completed without error 00% 26418 - # 3 Short offline Completed without error 00% 26414 - # 4 Short offline Completed without error 00% 25317 - # 5 Short offline Completed without error 00% 24369 - # 6 Short offline Completed without error 00% 19877 - # 7 Short offline Completed without error 00% 10054 - # 8 Short offline Completed without error 00% 10033 - # 9 Short offline Completed without error 00% 9804 - #10 Short offline Completed without error 00% 9804 - #11 Short offline Completed without error 00% 9804 - #12 Short offline Completed without error 00% 9780 - #13 Short offline Completed without error 00% 9775 - #14 Short offline Completed without error 00% 9768 - #15 Short offline Aborted by host 90% 5888 - #16 Short offline Completed without error 00% 5886 - #17 Short offline Completed without error 00% 5886 - #18 Short offline Completed without error 00% 5886 - #19 Short offline Completed without error 00% 5886 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 18/36 Celsius Lifetime Min/Max Temperature: 0/57 Celsius Specified Max Operating Temperature: 37 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (24) Index Estimated Time Temperature Celsius 25 2023-03-16 13:30 34 *************** ... ..( 8 skipped). .. *************** 34 2023-03-16 13:39 34 *************** 35 2023-03-16 13:40 33 ************** ... ..( 22 skipped). .. ************** 58 2023-03-16 14:03 33 ************** 59 2023-03-16 14:04 34 *************** 60 2023-03-16 14:05 34 *************** 61 2023-03-16 14:06 33 ************** 62 2023-03-16 14:07 34 *************** 63 2023-03-16 14:08 33 ************** ... ..( 12 skipped). .. ************** 76 2023-03-16 14:21 33 ************** 77 2023-03-16 14:22 34 *************** 78 2023-03-16 14:23 ? - 79 2023-03-16 14:24 ? - 80 2023-03-16 14:25 19 - 81 2023-03-16 14:26 21 ** 82 2023-03-16 14:27 21 ** 83 2023-03-16 14:28 22 *** 84 2023-03-16 14:29 24 ***** 85 2023-03-16 14:30 25 ****** 86 2023-03-16 14:31 ? - 87 2023-03-16 14:32 29 ********** 88 2023-03-16 14:33 30 *********** 89 2023-03-16 14:34 31 ************ ... ..( 4 skipped). .. ************ 94 2023-03-16 14:39 31 ************ 95 2023-03-16 14:40 32 ************* ... ..( 5 skipped). .. ************* 101 2023-03-16 14:46 32 ************* 102 2023-03-16 14:47 33 ************** 103 2023-03-16 14:48 33 ************** 104 2023-03-16 14:49 32 ************* 105 2023-03-16 14:50 33 ************** 106 2023-03-16 14:51 33 ************** 107 2023-03-16 14:52 32 ************* 108 2023-03-16 14:53 33 ************** 109 2023-03-16 14:54 33 ************** 110 2023-03-16 14:55 ? - 111 2023-03-16 14:56 19 - 112 2023-03-16 14:57 20 * 113 2023-03-16 14:58 22 *** 114 2023-03-16 14:59 23 **** 115 2023-03-16 15:00 25 ****** 116 2023-03-16 15:01 25 ****** 117 2023-03-16 15:02 26 ******* 118 2023-03-16 15:03 27 ******** 119 2023-03-16 15:04 28 ********* 120 2023-03-16 15:05 28 ********* 121 2023-03-16 15:06 29 ********** 122 2023-03-16 15:07 29 ********** 123 2023-03-16 15:08 29 ********** 124 2023-03-16 15:09 30 *********** 125 2023-03-16 15:10 30 *********** 126 2023-03-16 15:11 31 ************ 127 2023-03-16 15:12 31 ************ 0 2023-03-16 15:13 31 ************ 1 2023-03-16 15:14 32 ************* 2 2023-03-16 15:15 32 ************* 3 2023-03-16 15:16 32 ************* 4 2023-03-16 15:17 33 ************** 5 2023-03-16 15:18 33 ************** 6 2023-03-16 15:19 33 ************** 7 2023-03-16 15:20 34 *************** ... ..( 8 skipped). .. *************** 16 2023-03-16 15:29 34 *************** 17 2023-03-16 15:30 35 **************** 18 2023-03-16 15:31 35 **************** 19 2023-03-16 15:32 35 **************** 20 2023-03-16 15:33 36 ***************** ... ..( 3 skipped). .. ***************** 24 2023-03-16 15:37 36 ***************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS