/dev/ada0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.2-RELEASE-p3 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA100 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MS2OA8K0 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 19 14:00:07 2025 IST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7167) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 120) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 142 142 054 - 70 3 Spin_Up_Time POS--- 132 132 024 - 177 (Average 171) 4 Start_Stop_Count -O--C- 100 100 000 - 588 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 113 113 020 - 35 9 Power_On_Hours -O--C- 099 099 000 - 8721 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 587 192 Power-Off_Retract_Count -O--CK 100 100 000 - 609 193 Load_Cycle_Count -O--C- 100 100 000 - 609 194 Temperature_Celsius -O---- 181 181 000 - 33 (Min/Max 16/55) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 24/37 Celsius Lifetime Min/Max Temperature: 16/55 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (81) Index Estimated Time Temperature Celsius 82 2025-05-19 11:53 33 ************** ... ..(126 skipped). .. ************** 81 2025-05-19 14:00 33 ************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 587 --- Lifetime Power-On Resets 0x01 0x010 4 8721 --- Power-on Hours 0x01 0x018 6 10989293043 --- Logical Sectors Written 0x01 0x020 6 183749355 --- Number of Write Commands 0x01 0x028 6 66578992421 --- Logical Sectors Read 0x01 0x030 6 200771488 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 8719 --- Spindle Motor Power-on Hours 0x03 0x010 4 8719 --- Head Flying Hours 0x03 0x018 4 609 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 32 --- Read Recovery Attempts 0x03 0x030 4 3 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x010 1 33 N-- Average Short Term Temperature 0x05 0x018 1 35 N-- Average Long Term Temperature 0x05 0x020 1 55 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 46 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 39 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 2436 --- Number of Hardware Resets 0x06 0x010 4 1764 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/ada1 smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.2-RELEASE-p3 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 870 EVO 500GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: SVT01B6Q User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 19 14:00:09 2025 IST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 088 088 010 - 67 9 Power_On_Hours -O--CK 097 097 000 - 11382 12 Power_Cycle_Count -O--CK 099 099 000 - 589 177 Wear_Leveling_Count PO--C- 098 098 000 - 41 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 088 088 010 - 67 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 088 088 010 - 67 187 Uncorrectable_Error_Cnt -O--CK 099 099 000 - 10 190 Airflow_Temperature_Cel -O--CK 068 048 000 - 32 195 ECC_Error_Rate -O-RC- 199 199 000 - 10 199 CRC_Error_Count -OSRCK 099 099 000 - 7 235 POR_Recovery_Count -O--C- 099 099 000 - 98 241 Total_LBAs_Written -O--CK 099 099 000 - 39285677592 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 10 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [1] occurred at disk power-on lifetime: 10941 hours (455 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 90 00 00 0e 37 3c 00 40 00 Error: WP at LBA = 0x0e373c00 = 238500864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 0a 00 00 90 00 00 0e 37 3c 00 40 12 00:19:31.156 WRITE FPDMA QUEUED 61 0a 00 00 88 00 00 0e 37 32 00 40 11 00:19:31.156 WRITE FPDMA QUEUED 61 0a 00 00 80 00 00 0e 37 28 00 40 10 00:19:31.156 WRITE FPDMA QUEUED 61 04 08 00 78 00 00 0e 37 23 f8 40 0f 00:19:31.156 WRITE FPDMA QUEUED 61 0a 00 00 70 00 00 0e 37 19 f8 40 0e 00:19:31.156 WRITE FPDMA QUEUED Error 9 [0] occurred at disk power-on lifetime: 10941 hours (455 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 d0 00 00 0e 36 a8 00 40 00 Error: WP at LBA = 0x0e36a800 = 238462976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 0a 00 00 d0 00 00 0e 36 a8 00 40 1a 00:19:30.948 WRITE FPDMA QUEUED 61 09 b8 00 c8 00 00 0e 36 9e 48 40 19 00:19:30.948 WRITE FPDMA QUEUED 61 02 48 00 c0 00 00 0e 36 9c 00 40 18 00:19:30.948 WRITE FPDMA QUEUED 61 0a 00 00 b8 00 00 0e 36 92 00 40 17 00:19:30.948 WRITE FPDMA QUEUED 61 0a 00 00 b0 00 00 0e 36 88 00 40 16 00:19:30.948 WRITE FPDMA QUEUED Error 8 [3] occurred at disk power-on lifetime: 10941 hours (455 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 f8 00 00 0c d7 b2 00 40 00 Error: UNC at LBA = 0x0cd7b200 = 215462400 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 f8 00 00 0c d7 b2 00 40 1f 00:19:30.649 READ FPDMA QUEUED 60 01 00 00 b8 00 00 0c d7 b1 00 40 17 00:19:30.649 READ FPDMA QUEUED 60 01 00 00 b0 00 00 0c d7 b0 00 40 16 00:19:30.649 READ FPDMA QUEUED 60 00 10 00 a8 00 00 0c d7 c3 70 40 15 00:19:30.649 READ FPDMA QUEUED 60 00 50 00 a0 00 00 0c d7 c9 00 40 14 00:19:30.649 READ FPDMA QUEUED Error 7 [2] occurred at disk power-on lifetime: 10940 hours (455 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 b0 00 00 0f ef 28 88 40 00 Error: UNC at LBA = 0x0fef2888 = 267331720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b0 00 00 0f ef 28 88 40 16 00:09:32.982 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 06 30 40 01 00:09:32.982 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 30 40 01 00:09:32.982 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 40 01 00:09:32.982 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 08 30 40 01 00:09:32.982 READ LOG DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 26/40 Celsius Lifetime Min/Max Temperature: 20/52 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (81) Index Estimated Time Temperature Celsius 82 2025-05-18 16:50 29 ********** 83 2025-05-18 17:00 29 ********** 84 2025-05-18 17:10 30 *********** 85 2025-05-18 17:20 31 ************ ... ..( 14 skipped). .. ************ 100 2025-05-18 19:50 31 ************ 101 2025-05-18 20:00 30 *********** 102 2025-05-18 20:10 30 *********** 103 2025-05-18 20:20 29 ********** 104 2025-05-18 20:30 29 ********** 105 2025-05-18 20:40 30 *********** 106 2025-05-18 20:50 29 ********** 107 2025-05-18 21:00 29 ********** 108 2025-05-18 21:10 30 *********** 109 2025-05-18 21:20 29 ********** 110 2025-05-18 21:30 29 ********** 111 2025-05-18 21:40 29 ********** 112 2025-05-18 21:50 30 *********** 113 2025-05-18 22:00 29 ********** 114 2025-05-18 22:10 29 ********** 115 2025-05-18 22:20 30 *********** 116 2025-05-18 22:30 29 ********** 117 2025-05-18 22:40 30 *********** 118 2025-05-18 22:50 29 ********** ... ..( 6 skipped). .. ********** 125 2025-05-19 00:00 29 ********** 126 2025-05-19 00:10 30 *********** 127 2025-05-19 00:20 29 ********** 0 2025-05-19 00:30 29 ********** 1 2025-05-19 00:40 30 *********** 2 2025-05-19 00:50 29 ********** ... ..( 2 skipped). .. ********** 5 2025-05-19 01:20 29 ********** 6 2025-05-19 01:30 30 *********** 7 2025-05-19 01:40 30 *********** 8 2025-05-19 01:50 29 ********** ... ..( 3 skipped). .. ********** 12 2025-05-19 02:30 29 ********** 13 2025-05-19 02:40 30 *********** 14 2025-05-19 02:50 29 ********** 15 2025-05-19 03:00 30 *********** 16 2025-05-19 03:10 29 ********** ... ..( 13 skipped). .. ********** 30 2025-05-19 05:30 29 ********** 31 2025-05-19 05:40 30 *********** 32 2025-05-19 05:50 30 *********** 33 2025-05-19 06:00 29 ********** ... ..( 2 skipped). .. ********** 36 2025-05-19 06:30 29 ********** 37 2025-05-19 06:40 30 *********** 38 2025-05-19 06:50 29 ********** 39 2025-05-19 07:00 29 ********** 40 2025-05-19 07:10 29 ********** 41 2025-05-19 07:20 30 *********** 42 2025-05-19 07:30 30 *********** 43 2025-05-19 07:40 31 ************ 44 2025-05-19 07:50 31 ************ 45 2025-05-19 08:00 29 ********** ... ..( 2 skipped). .. ********** 48 2025-05-19 08:30 29 ********** 49 2025-05-19 08:40 30 *********** 50 2025-05-19 08:50 29 ********** ... ..( 5 skipped). .. ********** 56 2025-05-19 09:50 29 ********** 57 2025-05-19 10:00 30 *********** 58 2025-05-19 10:10 30 *********** 59 2025-05-19 10:20 30 *********** 60 2025-05-19 10:30 31 ************ 61 2025-05-19 10:40 32 ************* 62 2025-05-19 10:50 32 ************* 63 2025-05-19 11:00 33 ************** 64 2025-05-19 11:10 31 ************ 65 2025-05-19 11:20 32 ************* 66 2025-05-19 11:30 32 ************* 67 2025-05-19 11:40 33 ************** 68 2025-05-19 11:50 32 ************* 69 2025-05-19 12:00 31 ************ 70 2025-05-19 12:10 32 ************* ... ..( 5 skipped). .. ************* 76 2025-05-19 13:10 32 ************* 77 2025-05-19 13:20 31 ************ 78 2025-05-19 13:30 31 ************ 79 2025-05-19 13:40 32 ************* 80 2025-05-19 13:50 31 ************ 81 2025-05-19 14:00 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 589 --- Lifetime Power-On Resets 0x01 0x010 4 11382 --- Power-on Hours 0x01 0x018 6 39285677592 --- Logical Sectors Written 0x01 0x020 6 338888422 --- Number of Write Commands 0x01 0x028 6 35883682211 --- Logical Sectors Read 0x01 0x030 6 624824383 --- Number of Read Commands 0x01 0x038 6 2102000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 10 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1142 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 2915 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 7 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 6 Command failed due to ICRC error 0x0002 2 1123 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 1123 R_ERR response for host-to-device data FIS 0x0005 2 25 R_ERR response for non-data FIS 0x0006 2 25 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1131 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1131 Device-to-host register FISes sent due to a COMRESET 0x000b 2 1117 CRC errors within host-to-device FIS 0x000d 2 31 Non-CRC errors within host-to-device FIS 0x000f 2 1096 R_ERR response for host-to-device data FIS, CRC 0x0010 2 27 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 21 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 4 R_ERR response for host-to-device non-data FIS, non-CRC