[...] ---<<BOOT>>--- [...] Copyright (c) 668B-5668 The FreeBSD Project. [...] Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 [...] The Regents of the University of California. All rights reserved. [...] FreeBSD is a registered trademark of The FreeBSD Foundation. [...] FreeBSD 12.3-RELEASE-p6 #XigmaNAS: Fri Aug 19 01:04:36 CEST 2022 [...] XXX@XXX:/usr/obj/XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX amd64 [...] FreeBSD clang version 10.0.1 (XXX@XXX:llvm/llvm-project.git llvmorg-10.0.1-0-gef32c611aa2) [...] VT(vga): resolution 640x480 [...] CPU: Intel(R) Pentium(R) CPU G3220 @ 3.00GHz (2993.13-MHz K8-class CPU) [...] Origin="GenuineIntel" Id=0x306c3 Family=0x6 Model=0x3c Stepping=3 [...] Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> [...] Features2=0x4ddaebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,MOVBE,POPCNT,TSCDLT,XSAVE,OSXSAVE,RDRAND> [...] AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM> [...] AMD Features2=0x21<LAHF,ABM> [...] Structured Extended Features=0x2603<FSGSBASE,TSCADJ,ERMS,INVPCID,NFPUSG> [...] Structured Extended Features3=0xc000000<IBPB,STIBP> [...] XSAVE Features=0x1<XSAVEOPT> [...] VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID [...] TSC: P-state invariant, performance statistics [...] real memory = 8589934592 (8192 MB) [...] avail memory = 8013955072 (7642 MB) [...] Event timer "LAPIC" quality 600 [...] ACPI APIC Table: <ALASKA A M I> [...] FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs [...] FreeBSD/SMP: 1 package(s) x 2 core(s) [...] random: unblocking device. [...] ioapic0 <Version 2.0> irqs 0-23 on motherboard [...] Launching APs: 1 [...] Timecounter "TSC-low" frequency 1496564750 Hz quality 1000 [...] random: entropy device external interface [...] WARNING: Device "g_ctl" is Giant locked and may be deleted before FreeBSD 14.0. [...] md0: Preloaded image </mfsroot> 134217728 bytes at 0xffffffff82840a08 [...] WARNING: Device "pci" is Giant locked and may be deleted before FreeBSD 14.0. [...] [ath_hal] loaded [...] module_register_init: MOD_LOAD (vesa, 0xffffffff812545f0, 0) error 19 [...] random: registering fast source Intel Secure Key RNG [...] random: fast provider: "Intel Secure Key RNG" [...] WARNING: Device "spkr" is Giant locked and may be deleted before FreeBSD 14.0. [...] WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 14.0. [...] kbd1 at kbdmux0 [...] 000.000152 [4337] netmap_init netmap: loaded module [...] mlx5en: Mellanox Ethernet driver 3.6.0 (December 2020) [...] nexus0 [...] vtvga0: <VT VGA driver> on motherboard [...] cryptosoft0: <software crypto> on motherboard [...] aesni0: No AES or SHA support. [...] acpi0: <ALASKA A M I> on motherboard [...] acpi0: Power Button (fixed) [...] cpu0: <ACPI CPU> on acpi0 [...] hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 [...] Timecounter "HPET" frequency 14318180 Hz quality 950 [...] Event timer "HPET" frequency 14318180 Hz quality 550 [...] Event timer "HPET1" frequency 14318180 Hz quality 440 [...] Event timer "HPET2" frequency 14318180 Hz quality 440 [...] Event timer "HPET3" frequency 14318180 Hz quality 440 [...] Event timer "HPET4" frequency 14318180 Hz quality 440 [...] Event timer "HPET5" frequency 14318180 Hz quality 440 [...] Event timer "HPET6" frequency 14318180 Hz quality 440 [...] atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0 [...] atrtc0: Warning: Couldn't map I/O. [...] atrtc0: registered as a time-of-day clock, resolution 1.000000s [...] Event timer "RTC" frequency 32768 Hz quality 0 [...] attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0 [...] Timecounter "i8254" frequency 1193182 Hz quality 0 [...] Event timer "i8254" frequency 1193182 Hz quality 100 [...] Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 [...] acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0 [...] pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 [...] pci0: <ACPI PCI bus> on pcib0 [...] pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0 [...] pci1: <ACPI PCI bus> on pcib1 [...] mps0: <Avago Technologies (LSI) SAS2008> port 0xe000-0xe0ff mem 0xf7dc0000-0xf7dc3fff,0xf7d80000-0xf7dbffff irq 16 at device 0.0 on pci1 [...] mps0: Firmware: XXX.XXX.XXX.XXX, Driver: XXX.XXX.XXX.XXX-fbsd [...] mps0: IOCCapabilities: 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc> [...] vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xf7800000-0xf7bfffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0 [...] vgapci0: Boot video device [...] xhci0: <Intel Lynx Point USB 3.0 controller> mem 0xf7e00000-0xf7e0ffff irq 21 at device 20.0 on pci0 [...] xhci0: 32 bytes context size, 64-bit DMA [...] xhci0: Port routing mask set to 0xffffffff [...] usbus0 on xhci0 [...] usbus0: 5.0Gbps Super Speed USB v3.0 [...] pci0: <simple comms> at device 22.0 (no driver attached) [...] ehci0: <Intel Lynx Point USB 2.0 controller USB-B> mem 0xf7e18000-0xf7e183ff irq 20 at device 26.0 on pci0 [...] usbus1: EHCI version 1.0 [...] usbus1 on ehci0 [...] usbus1: 480Mbps High Speed USB v2.0 [...] hdac0: <Intel Lynx Point HDA Controller> mem 0xf7e10000-0xf7e13fff irq 22 at device 27.0 on pci0 [...] pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 [...] pci2: <ACPI PCI bus> on pcib2 [...] pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 [...] pci3: <ACPI PCI bus> on pcib3 [...] re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xd000-0xd0ff mem 0xf7c00000-0xf7c00fff,0xf0000000-0xf0003fff irq 18 at device 0.0 on pci3 [...] re0: Using 1 MSI-X message [...] re0: ASPM disabled [...] re0: Chip rev. 0x4c000000 [...] re0: MAC rev. 0x00000000 [...] miibus0: <MII bus> on re0 [...] rgephy0: <RTL8251/8153 1000BASE-T media interface> PHY 1 on miibus0 [...] rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow [...] re0: Using defaults for TSO: 65518/35/2048 [...] re0: Ethernet address: ... [...] re0: netmap queues/slots: TX 1/256, RX 1/256 [...] ehci1: <Intel Lynx Point USB 2.0 controller USB-A> mem 0xf7e17000-0xf7e173ff irq 23 at device 29.0 on pci0 [...] usbus2: EHCI version 1.0 [...] usbus2 on ehci1 [...] usbus2: 480Mbps High Speed USB v2.0 [...] isab0: <PCI-ISA bridge> at device 31.0 on pci0 [...] isa0: <ISA bus> on isab0 [...] ahci0: <Intel Lynx Point AHCI SATA controller> port 0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf090-0xf097,0xf080-0xf083,0xf060-0xf07f mem 0xf7e16000-0xf7e167ff irq 19 at device 31.2 on pci0 [...] ahci0: AHCI v1.30 with 4 6Gbps ports, Port Multiplier not supported [...] ahcich0: <AHCI channel> at channel 0 on ahci0 [...] ahcich1: <AHCI channel> at channel 1 on ahci0 [...] ahciem0: <AHCI enclosure management bridge> on ahci0 [...] acpi_button0: <Power Button> on acpi0 [...] acpi_tz0: <Thermal Zone> on acpi0 [...] acpi_tz1: <Thermal Zone> on acpi0 [...] atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 [...] atkbd0: <AT Keyboard> irq 1 on atkbdc0 [...] kbd0 at atkbd0 [...] atkbd0: [GIANT-LOCKED] [...] coretemp0: <CPU On-Die Thermal Sensors> on cpu0 [...] est0: <Enhanced SpeedStep Frequency Control> on cpu0 [...] p4tcc0: <CPU Frequency Thermal Control> on cpu0 [...] ZFS filesystem version: 5 [...] ZFS storage pool version: features support (5000) [...] Timecounters tick every 1.000 msec [...] iSCSI boot driver version 0.3.2 [...] NIC0: IP address: XXXX:XXXX:XXXX:XXXX:XXXX:XXXX:XXXX:XXXX [...] NIC0: Prefix: 0 [...] NIC0: MAC address: XXX [...] TGT0: Target IP address: XXXX:XXXX:XXXX:XXXX:XXXX:XXXX:XXXX:XXXX [...] TGT0: Target Port: 0 [...] TGT0: Target LUN: 0 [...] Boot NIC: lo0 [...] Configure IPv6 by NIC0 [...] in6_control error [...] IP set error [...] ugen0.1: <0x8086 XHCI root HUB> at usbus0 [...] ugen1.1: <Intel EHCI root HUB> at usbus1 [...] uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 [...] uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 [...] lo0: link state changed to UP [...] ugen2.1: <Intel EHCI root HUB> at usbus2 [...] uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2 [...] hdacc0: <Realtek ALC887 HDA CODEC> at cad 0 on hdac0 [...] hdaa0: <Realtek ALC887 Audio Function Group> at nid 1 on hdacc0 [...] pcm0: <Realtek ALC887 (Rear Analog)> at nid 20 and 24,26 on hdaa0 [...] pcm1: <Realtek ALC887 (Front Analog)> at nid 27 and 25 on hdaa0 [...] pcm2: <Realtek ALC887 (Internal Digital)> at nid 17 on hdaa0 [...] Trying to mount root from ufs:/dev/md0 []... [...] uhub0: 17 ports with 17 removable, self powered [...] uhub2: 2 ports with 2 removable, self powered [...] uhub1: 2 ports with 2 removable, self powered [...] ugen2.2: <vendor 0x8087 product 0x8000> at usbus2 [...] uhub3 on uhub2 [...] uhub3: <vendor 0x8087 product 0x8000, class 9/0, rev 2.00/0.05, addr 2> on usbus2 [...] ugen1.2: <vendor 0x8087 product 0x8008> at usbus1 [...] uhub4 on uhub1 [...] uhub4: <vendor 0x8087 product 0x8008, class 9/0, rev 2.00/0.05, addr 2> on usbus1 [...] uhub4: 4 ports with 4 removable, self powered [...] uhub3: 6 ports with 6 removable, self powered [...] ugen0.2: <SMART USB 8GB 3> at usbus0 [...] umass0 on uhub0 [...] umass0: <SMART USB 8GB 3, class 0/0, rev 2.10/1.10, addr 1> on usbus0 [...] umass0: SCSI over Bulk-Only; quirks = 0x8100 [...] umass0:4:0: Attached to scbus4 [...] ses0 at ahciem0 bus 0 scbus3 target 0 lun 0 [...] ses0: <AHCI SGPIO Enclosure 2.00 0001> SEMB S-E-S 2.00 device [...] ses0: SEMB SES Device [...] ada0 at ahcich0 bus 0 scbus1 target 0 lun 0 [...] ada0: <P300-MTFDDAC100SAL 0004> ACS-2 ATA SATA 3.x device [...] ada0: Serial Number... [...] ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) [...] ada0: Command Queueing enabled [...] ada0: 95396MB (195371568 512 byte sectors) [...] ses0: pass8,ada0 in 'Slot 00', SATA Slot: scbus1 target 0 [...] ada1 at ahcich1 bus 0 scbus2 target 0 lun 0 [...] ada1: <P300-MTFDDAC100SAL 0004> ACS-2 ATA SATA 3.x device [...] ada1: Serial Number... [...] ada1: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) [...] ada1: Command Queueing enabled [...] ada1: 95396MB (195371568 512 byte sectors) [...] ses0: pass9,ada1 in 'Slot 01', SATA Slot: scbus2 target 0 [...] da8 at umass-sim0 bus 0 scbus4 target 0 lun 0 [...] da8: <SMART USB 8GB 3 0110> Removable Direct Access SPC-4 SCSI device [...] da8: Serial Number... [...] da8: 40.000MB/s transfers [...] da8: 7552MB (15466496 512 byte sectors) [...] da8: quirks=0x2<NO_6_BYTE> [...] da7 at mps0 bus 0 scbus0 target 16 lun 0 [...] da7: <ATA WDC WD10EFRX-68P 1A01> Fixed Direct Access SPC-4 SCSI device [...] da7: Serial Number... [...] da7: 600.000MB/s transfers [...] da7: Command Queueing enabled [...] da7: 953869MB (1953525168 512 byte sectors) [...] da7: quirks=0x8<4K> [...] da3 at mps0 bus 0 scbus0 target 12 lun 0 [...] da3: <ATA ST1000NM0033-9ZM SN03> Fixed Direct Access SPC-4 SCSI device [...] da3: Serial Number... [...] da3: 600.000MB/s transfers [...] da3: Command Queueing enabled [...] da3: 953869MB (1953525168 512 byte sectors) [...] da0 at mps0 bus 0 scbus0 target 8 lun 0 [...] da0: <ATA ST1000NM0011 PT05> Fixed Direct Access SPC-4 SCSI device [...] da0: Serial Number... [...] da0: 600.000MB/s transfers [...] da0: Command Queueing enabled [...] da0: 953869MB (1953525168 512 byte sectors) [...] da6 at mps0 bus 0 scbus0 target 15 lun 0 [...] da6: <ATA ST1000NM0033-9ZM SN03> Fixed Direct Access SPC-4 SCSI device [...] da6: Serial Number... [...] da6: 600.000MB/s transfers [...] da6: Command Queueing enabled [...] da6: 953869MB (1953525168 512 byte sectors) [...] da2 at mps0 bus 0 scbus0 target 10 lun 0 [...] da2: <ATA ST3000DM001-1ER1 CC26> Fixed Direct Access SPC-4 SCSI device [...] da2: Serial Number... [...] da2: 600.000MB/s transfers [...] da2: Command Queueing enabled [...] da2: 2861588MB (5860533168 512 byte sectors) [...] da2: quirks=0x8<4K> [...] da5 at mps0 bus 0 scbus0 target 14 lun 0 [...] da5: <ATA ST3000DM001-1ER1 CC26> Fixed Direct Access SPC-4 SCSI device [...] da5: Serial Number... [...] da5: 600.000MB/s transfers [...] da5: Command Queueing enabled [...] da5: 2861588MB (5860533168 512 byte sectors) [...] da5: quirks=0x8<4K> [...] da4 at mps0 bus 0 scbus0 target 13 lun 0 [...] da4: <ATA Hitachi HUA72201 I52H> Fixed Direct Access SPC-4 SCSI device [...] da4: Serial Number... [...] da4: 300.000MB/s transfers [...] da4: Command Queueing enabled [...] da4: 953869MB (1953525168 512 byte sectors) [...] da1 at mps0 bus 0 scbus0 target 9 lun 0 [...] da1: <ATA Hitachi HUA72201 I52H> Fixed Direct Access SPC-4 SCSI device [...] da1: Serial Number... [...] da1: 300.000MB/s transfers [...] da1: Command Queueing enabled [...] da1: 953869MB (1953525168 512 byte sectors) [...] re0: link state changed to DOWN